Datasheet

2-25
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: [phone] • FAX: [phone] •www.dialight.com
2
3 x 5mm Rectangular
®
Optopipe
TM
Optical Light Pipe, 2 Array (RJ45 Jack)
515-1070
19.05
[.750]
13.98
[.550]
2.54
[.100]
5.08
[.200]
2 PLCS
3.05
[.120]
1.91
[.075]
C.L. LEDS
27.94
[1.100]
35.26
[1.388]
3.66
[.144]
.71
[.028]
1.50
[.059]
.99
[.039]
.99
[.039]
2.01
[.079]
1.57
[.062]
1.35
[.053]
13.98
[.550]
6.99
[.275]
27.94
±
.05
[1.100
±
.002]
2X Ø 2.87
±
.05
[.113
±
.002]
RECOMMENDED SOLDER PAD/HOLES LAYOUT
FOR BI-COLOR LEDS
C.L. MOUNTING
PIN #1
3.56
[.140]
20.57
[.81]
31.24
[1.23]
DIFFUSED
FRONT
SURFACE
27.43
[1.080]
7.62
±
.15
[.300
±
.006
]
1.57
[.062]
DIRECTION
OF LIGHT
3.93
[.155]
29.0
[1.142]
FRONT
PANEL
Dimensions in mm [inches]
Recommended
MicroLED SMT LEDs
for use with 515-1070
PART NO. COLOR PAGE #
597-3001-1xx Red 1-19
597-3111-1xx AlGaAs Red 1-19
597-3111-5xx AlGaAs Red 1-30
597-3211-1xx Orange 1-19
597-3211-5xx Orange 1-30
597-3301-1xx Green 1-19
597-3301-5xx Green 1-30
597-3401-1xx Yellow 1-19
597-3401-5xx Yellow 1-30
597-7701-1xx Red/Green 1-20
597-7701-5xx Red/Green 1-31
597-7721-1xx Yellow/Green 1-20
597-7721-5xx Yellow/Green 1-31
597-7731-1xx Red/Yellow 1-20
Features
• Complements Dialight’s 515-1022 Four Array Optopipe
Light Pipe
• Allows indicators to be positioned above corresponding
RJ45 jack or D-Subminiature
• High transmissivity polycarbonate material
• UL94V-0 compliance
• ESD protection (circuit isolation from front panel)
• Wide viewing angle
• Arrays reduce insertion costs
• Secures to PCB by press-fit
LED Data
For absolute maximum ratings and other
electrical and optical data on the recommended
LEDs, refer to LED data sheets.
Dialight Optopipe Light Pipe Description
This light pipe’s two 3 x 5mm rectangular light emitting surfaces appear bright and are optically well isolated. The light
pipe is reliably held in place by 2 press-fit pins located at either end of the light pipe array. This Optopipe™ functions as a
through-the-case indicator by conducting the light over the top of connectors or switches. A textured finish on the 2 light
emitting surfaces maximizes the viewing angle. The recommended light sources are Dialight's 597 Series PLCC-2 or
PLCC-4 Type SMT LEDs. The LEDs are mounted in a straight line on an 0.550" pitch. The light pipe material is water
clear transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index.
Dialight can provide custom Optopipe™ solutions for your applications.
Operating/Storage Temperature
–30°C to +100°C
NOTE: designed for
post-reflow
PC board insertion.