user manual TM TM www.diablopaintball.com .68 CALIBER ELECTRONIC PAINTBALL MARKER Meets or exceeds ASTM standards.
TABLE OF CONTENTS: Page Topic(s) 1 Warning and Rules Safe Marker Handling Warranty Information Welcome Initial Assembly Battery Installation Attaching Propellant Source Attaching Feeder/Hopper Loading Paintballs Parts Key Exploded Diagram De-Gassing Chronographing Maintenance Storage Trouble Shooting Guide Notes Warranty Registration 2 3 4 9 10 11 12 14 15 17 WARNING: This is not a toy. Misuse may cause serious injury or death.
WARRANTY INFORMATION STANDARD WARRANTY: The manufacturer warranties to the original customer that this product is free from defects in material and workmanship under normal use and service for a period of 90 days from the original date of purchase by the initial owner/purchaser. The manufacturer agrees to repair or replace (at its discretion) any product within a reasonable period of time.
Numbers shown in parentheses following part names correspond to the numbers on the Parts key located on the centerfold pages of this manual. INITIAL ASSEMBLY 1. 2. 3. 4. Screw Barrel (23) hand tight into the Main Body (34) making sure the Barrel O-Ring (16) is properly seated between the Barrel and the Main Body to prevent the Barrel from vibrating loose during rapid firing.
Battery Saver 1. With the LCD screen reading: TIMER 00:00 2. Point the marker in a safe direction. 3. Make sure the barrel blocking device is properly installed. 4. Press and release Command Button screen will read: POWER AUTO This indicates that the marker will automatically shut down after 30 minutes if not fired. Eyes 1. 2. 3. 4. With the LCD screen reading: POWER AUTO Point the marker in a safe direction. Make sure the barrel blocking device is properly installed.
Turning OFF the Battery saver 1. With the LCD screen reading: 2. 3. 4. 5. POWER AUTO Point the marker in a safe direction. Make sure the barrel blocking device is properly installed. Press and release Adjustment Button screen will read: POWER ON (Flashing) ATTACHING PROPELLANT SOURCE 1. 2. 3. 4. 5. Press and release the Command Button. 6. Note: The marker will not automatically shut off in this mode.
16 25A 33 16 25 Meets or exceeds ASTM standards. .68 CALIBER ELECTRONIC PAINTBALL MARKER TM 26 Part Name Hammer Main Spring Recoil Pad Spring Strut Quick Strip Pin A. Cotter Pin Gas Valve Cup Seal Valve Spring Valve Gas Plug Valve Stop Pin Vertical Feed Neck A. ClampFeed Adjustment Velocity Adjuster A. Anti-Vibration O-Ring B. Locking Set Screw Ball Detent Tank Adapter A.
2. Point marker in a safe direction and load paintballs in the Feeder/Hopper. If you are using a non-motorized hopper, be sure to leave some room in the hopper for the balls to feed properly. CHRONOGRAPHING Never operate your marker without first checking the velocity and confirming that you are firing below that required on the field of play. At no time should the marker fire paintballs in excess of 300 feet per second.
MAINTENANCE Bolt 1. 2. 3. 4. 5. 6. 7. Pull the Bolt Pull Pin (28A) upwards until it “clicks”. Pull the Bolt Pull Pin rearward until the Bolt (28) comes out of the back of the Main Body (34). Clean the bolt thoroughly to include rinsing in warm water if needed. Lubricate the bolt with non-corrosive lubricant such as Empire Lube or Empire Oil. Return the bolt to the rear of the Main Body making sure to put the open end in first.
NOTES ON MONGOOSE: WARRANTY REGISTRATION: To assist us in providing the best customer service possible and to increase your warranty from 90 days to one year at no additional cost Complete and mail this to: Paintball Solutions 570 Mantua Blvd. Sewell, NJ 08080 Or register online at www.paintballsolutions.
