5418096 Metal Bunk Bed TM Twin/Full Silver Weight Limit: Upper Bed: 200 Lbs / 91 Kgs Lower Bed: 450 Lbs / 204 Kgs Thank you for purchasing from DHP! DO NOT RETURN TO THE STORE ! If parts are missing or damaged, we will gladly ship your replacement parts free of charge. Visit www.dhpfurniture.com/eng/support-home or call Toll-Free 1-800-267-1739 Date of Purchase Lot Number THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. C.W.
Warranty Information Read Before Beginning Assembly DHP warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect. This warranty covers one year from the date of original purchase. This is solely limited to the repair or replacement of defective parts and assembly labor is not included. This warranty does not apply to any product which has been improperly assembled, subjected to misuse or abuse or which has been altered or repaired in any way.
Parts C B A D E X Replacement Parts, Visit www.dhpfurniture.com/eng/support-home All in 1 big box! There are inner box(es) that include components required to complete this assembly. Post T917190 Post T917200 X1 X1 Post T917220 Post T917210 X1 X1 Before you throw the package, please use the Check Box to identify the parts and ensure that you have all the parts needed for the assembly.
1 2 4 3 Hardware Pack 5 Hardware Pack #: T5418096-09 ST 4.2 X 14mm X2 1/4" X 1 1/16" X8 5/16" X 3/4" 1/4" X 3/4" X 16 X 24 1/4" X 2 3/8" X2 7 6 8 1/4" X8 Wrench X1 4mm X1 Please do not completely tighten all the hardware, until the entire assembly is complete, unless otherwise indicated in the step-by-step instructions. The screw(s), bolt(s) to be used at each step are shown in actual size in the lower right corner of the page.
Step 1 Attach I to A/B and C/D with Attach T to A/B and C/D with . Please do not completely tighten the bolts of Part I & T, in order to easily assemble Parts M in Step 2. I I .
Step 2 Insert M x 2 onto A/B and C/D, then properly tighten the BOLTS from Step 1. These two holes are in the same side.
Step 3 Wide side of the slot should be facing up ! G Attach G x 2 to B/C and A/D with . Attach J x 2 to B/C and A/D with .
Step 4 M E 4.1 Attach E x 2 to A/D/M and B/C/M E 4 G with . 4.2 Then attach E x 2 to G x 2 with . 1 C 4.2 4.
Step 5 6 Attach Z x 2 to I x 2 and T x 2 with 2 and .
Step 6 Attach X to T x 2 with .
G 1 Step 7 G 1 2 Y 2 3 Insert O into G as illustrated. Then lock O into place with Y. Insert P into J as illustrated. Then lock P into place with Y.
O Step 8 Q W W 8.1 8.1 Attach W to O/P. 8.2 Attach Q to W alternating left and right. For better performance, attach the Slat Spacers Q at equal spaces. (Approximately = 17.5 inches or 445 mm for lower bed). 8.2 17.5" 17.5" 17.
Weight Limit: Upper Bed: 200 Lbs / 91 Kgs Lower Bed: 450 Lbs / 204 Kgs Helpful Hints ● Move your new furniture carefully, with two people lifting and carrying the unit to its new location. ● Your DHP furniture can be disassembled and reassembled to move. ● Clean the product with your favorite furniture polish and soft cloth. DO NOT use harsh chemicals or abrasive cleaners.
WARNINGS for Bunk Bed ● Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed. ● Always use the recommended size mattresses or mattress supports, or both, to help prevent the likelihood of entrapment or falls. ● Use only a twin mattress which is 74"-75" long and 37 1/2"-38 1/2" wide on upper bunk and a full mattress which is 74"-75" long and 53 1/2"-54 1/2" wide on lower bunk. ● Surface of mattress must be at least 5 in.
5418096 NO LO REGRESE A LA TIENDA ! Metal Bunk Bed Si le faltan piezas o las que se incluyen están dañadas, con mucho gusto le enviaremos sus piezas de reemplazo sin cargo extra. Twin/Full Visite www.dhpfurniture.com/spa/support-home o llame gratis al 1-800-267-1739 Plata Fecha de compra N mero de lote ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD. POR FAVOR LEA Y GUARDE PARA SU REFERENCIA FUTURA.
Lea antes de comenzar a ensamblar ● Llame a nuestro número gratuito si necesita asistencia. ● Trabaje en un área espaciosa y cerca de donde su producto será utilizado, preferiblemente sobre una alfombra o utilice el cartón del empaque para proteger su piso y su producto. ● El número de personas recomendadas para el montaje de este producto es: 2 (sin embargo es recomendable contar con ayuda adicional). Tiempo estimado de ensamble es 1.5 horas. ● Asegúrese de que todas las partes están incluidas.
Límites de peso:200 Lbs / 91 Kgs en la cama superior; 450 Lbs / 204 Kgs en la cama inferior. Instrucciones Paso 1 Una I en A/B y C/D con . Precauc on Una T en A/B y C/D con . Por favor, no apretar completamente los pernos en Parte I & T, para facilitar el montaje de las Partes M en Paso 2. Paso 2 Insertar M x 2 en A/B y C/D, apriete completamente todos los PERNOS del Paso 1. Paso 3 Una G x 2 en B/C y A/D con . Una J x 2 en B/C y A/D con . Paso 4 4.1 Una E x 2 en A/D/M y B/C/M con . 4.
5418096 NE RETOURNEZ PAS AU MAGASIN ! Metal Bunk Bed Si une pièce est manquante ou endommagée, nous vous expédierons avec plaisir vos pièces de remplacement gratuitement. Twin/Full Visitez www.dhpfurniture.
Avant de commencer l'assemblage Si vous avez besoin d'aide, appelez notre service la client le sans frais. Travailler dans un endroit spacieux et près du lieu où l'unité sera utilisée, préférablement sur un tapis, ou sur un morceau de l'emballage pour protéger le plancher et le produit. Nombre de personnes recommand pour l'assemblage: 2 (cependant il vaut mieux toujours d'avoir une main suppl mentaire). Le temps d'assemblage estim est de 1.5 heures. Assurez-vous que toutes les pi ces sont incluses.
Limite de Poids: 200 Lbs / 91 Kgs sur le lit supérieur; 450 Lbs / 204 Kgs sur le lit inférieur. Instructions tape 1 Attacher I à A/B et C/D avec Avertissement . Attacher T à A/B et C/D avec . Veuillez ne pas serrer complètement le boulon sur I & T, afin de faciliter l'assemblage de M dans l' tape 2. tape 2 Insérer M x 2 à A/B et C/D, serrez complètement tous les BOULONS de tape 1. tape 3 Attacher G x 2 à B/C et C/D avec . Attacher J x 2 à B/C et C/D avec . tape 4 4.
