Data Sheet

www. vkelcom.com
14
VK2828U7G5LF DataSheet
V.KEL Communications Equipment(SHENZHEN）Co., Ltd
VK-162 说明书
深圳市微科通讯设备有限公司
V1.0
G-M OUS E
8. Protocols for Setting U-blox Parameters
You can send commands through serial port to modify the settings. The HEX must be selected when you
send commands through the serial port of PC software.
It will cost 300ms to start the U-blox for the first time. Please send the following commands to set the
parameters after it starts.
8.1 Disable Outputting Commands
24 45 49 47 50 51 2c 44 54 4d 2a 33 42 0d 0a b5 62 06 01 03 00 f0 0a 00 04 23 -> Disable GPDTM
24 45 49 47 50 51 2c 47 42 53 2a 33 30 0d 0a b5 62 06 01 03 00 f0 09 00 03 21 -> Disable GPGBS
24 45 49 47 50 51 2c 47 47 41 2a 32 37 0d 0a b5 62 06 01 03 00 f0 00 00 fa 0f -> Disable GPGGA
24 45 49 47 50 51 2c 47 4c 4c 2a 32 31 0d 0a b5 62 06 01 03 00 f0 01 00 fb 11 -> Disable GPGLL
24 45 49 47 50 51 2c 47 52 53 2a 32 30 0d 0a b5 62 06 01 03 00 f0 06 00 00 1b -> Disable GPGRS
24 45 49 47 50 51 2c 47 53 41 2a 33 33 0d 0a b5 62 06 01 03 00 f0 02 00 fc 13 -> Disable GPGSA
24 45 49 47 50 51 2c 47 53 54 2a 32 36 0d 0a b5 62 06 01 03 00 f0 07 00 01 1d -> Disable GPGST
24 45 49 47 50 51 2c 47 53 56 2a 32 34 0d 0a b5 62 06 01 03 00 f0 03 00 fd 15 -> Disable GPGSV
24 45 49 47 50 51 2c 52 4d 43 2a 33 41 0d 0a b5 62 06 01 03 00 f0 04 00 fe 17 -> Disable GPRMC
24 45 49 47 50 51 2c 56 54 47 2a 32 33 0d 0a b5 62 06 01 03 00 f0 05 00 ff 19 -> Disable GPVTG
24 45 49 47 50 51 2c 5a 44 41 2a 33 39 0d 0a b5 62 06 01 03 00 f0 08 00 02 1f -> Disable GPZDA
8.2 Enable Outputting Commands
24 45 49 47 50 51 2c 44 54 4d 2a 33 42 0d 0a b5 62 06 01 03 00 f0 0a 01 05 24 -> Enable GPDTM
24 45 49 47 50 51 2c 47 42 53 2a 33 30 0d 0a b5 62 06 01 03 00 f0 09 01 04 22 -> Enable GPGBS
24 45 49 47 50 51 2c 47 47 41 2a 32 37 0d 0a b5 62 06 01 03 00 f0 00 01 fb 10 -> Enable GPGGA
24 45 49 47 50 51 2c 47 4c 4c 2a 32 31 0d 0a b5 62 06 01 03 00 f0 01 01 fc 12 -> Enable GPGLL
24 45 49 47 50 51 2c 47 52 53 2a 32 30 0d 0a b5 62 06 01 03 00 f0 06 01 01 1c -> Enable GPGRS
24 45 49 47 50 51 2c 47 53 41 2a 33 33 0d 0a b5 62 06 01 03 00 f0 02 01 fd 14 -> Enable GPGSA
24 45 49 47 50 51 2c 47 53 54 2a 32 36 0d 0a b5 62 06 01 03 00 f0 07 01 02 1e -> Enable GPGST
24 45 49 47 50 51 2c 47 53 56 2a 32 34 0d 0a b5 62 06 01 03 00 f0 03 01 fe 16 -> Enable GPGSV
24 45 49 47 50 51 2c 52 4d 43 2a 33 41 0d 0a b5 62 06 01 03 00 f0 04 01 ff 18 -> Enable GPRMC
24 45 49 47 50 51 2c 56 54 47 2a 32 33 0d 0a b5 62 06 01 03 00 f0 05 01 00 1a -> Enable GPVTG
24 45 49 47 50 51 2c 5a 44 41 2a 33 39 0d 0a b5 62 06 01 03 00 f0 08 01 03 20 -> Enable GPZDA
8.3 Set Baud Rate
 Set baud rate to 4800
b5 62 06 00 14 00 01 00 00 00 d0 08 00 00 c0 12 00 00 07 00 07 00 00 00 00 00 d3 fc b5 62 06 00 01 00 01 08 22
 Set baud rate to 9600
b5 62 06 00 14 00 01 00 00 00 d0 08 00 00 80 25 00 00 07 00 07 00 00 00 00 00 a6 cd b5 62 06 00 01 00 01 08 22