Data Sheet

4/5
Detent feeling has to remains
Contact resistance 200ΩMax
all items is shall be
for 1.5H,After which measurements shall be made.
all items is shall be
all items is shall be
Application time of soldering iron:within 3S
solder shall cover75% minimum
of the surface being immersed.
常温、常湿放置1.5小时后测试.
Specifications in clause
所有项应满足初期规格。
Specifications in clause
satisfied.
温度85±3℃的恒温箱中放置96±4小时,
in a thermostatic chamber.And the encoder shall
be subjected to standard atmospheric conditions
encoder shall be stored at temperature of40 ±2℃
with relative humidity of 90% to95% for96±4H
Cold
Resistance
heat
to Soldering
7-5.焊锡耐热性 使用基板:t=1.6mm的单面覆铜板.
measurements shall be made.
、形变、损破的体缘绝有得不.gniredlos piD 焊槽
Electrical characteristics
接触无异常.
7-6.焊锡性
Printed wiring board:single-sided copper clad
laminate board with thickness of 1.6mm.
Preheating:1.Surface temperature of board:100℃.
Soldering:Solder temperature:260±5℃ or less
shall be satisfied No
焊接:温度260±5℃或以下,时间3秒以内.
mechanical abnormality.预热:基板表面温度100℃以下,时间1分钟以内.
Solderability
The terminals shall be immersed into solder bath A new uniform coating of
温度300℃以下,时间3秒以内.
at 260℃for 3S±0.5S.
浸渍面须有75%以上焊锡附着
85±3℃for 96±4H in a thermostatic chamber.And
The encoder shall be stored at a temperature of
life
7 耐久性能 Endurance Characteristics
(5000 to 8000 continuous cycles for 24 hours.）
7-1.回转寿命
The shaft of encoder shall be rotated at a speed of
在无负荷条件下轴以600～1000周/小时速度回转，
600～1000cycles/H without electrical load,after with
条件
EC11正向系列规格书
规格项目
一日连续5000～8000次.
温度40±2℃,湿度90～95%的恒温恒湿槽中放置96±4
小时后,在常温、常湿中放置1.5小时后测试. The
7-2.耐湿性
Damp heat
7-3.耐热性
measurements shall be made.
尚余有轻微定位感.
CONDITIONS
EC11 FORWARD DIRECTION SERIES SPECIFICATION
Rotational
ITEM
The encoder shall be stored at a temperature of
所有项应满足初期规格。
Dry heat
-40±3℃for 96±4H in a thermostatic chamber.And 7-4.低温特性
measurements shall be made.
then the encoder.shall be subjected to standard
温度-40±3℃的恒温箱中放置96±4小时,
手焊 Manual soldering.
or less 2.Preheating time:within 1 minute.
Immersion time:within 3S
所有项应满足初期规格
Chattiring t1,t3≤5mS.Bounce t2≤3mS.
satisfied.
atmospheric conditions for 1.5H,After which
15,000±200cycles per above 100gf.cm.
■在力矩≤100gf.cm时30,000±200周
SPECIFICATIONS
端子间接触阻抗200Ω以下
□在力矩＞100gf.cm时15,000±200周.
30,000±200cycles per below 100gf.cm.
振荡 t1,t3≤5mS.突跳 t2≤3mS.
esualc ni snoitacificepS.试测后时小5.1置放湿常、温常
satisfied.
then the encoder.shall be subjected to standard
atmospheric conditions for 1.5H,After which
Bit temperature of soldering iron:300℃less than
端子在260℃±5℃温度的焊锡槽内浸锡3秒±0.5秒.