User's Manual

Please make sure all the devices are properly connected and receiver is not in
standby mode before you follow the troubleshooting guide below.
No video
1、Check the status of LED, and check if the HD media
player works normally.
2、Check if the joints and wires are damaged and make
sure they are correctly connected to corresponding
interface.
3、Ensure there is video on output devices.
4、Check the receiver is correctly connected to display
equipment.
5、Make sure all devices are working on supported
distance. Draw them closer and try it again.
Power LED off
1、 Make sure the power adaptor is correctly connected
and the voltage is 5V3A
2、 Make sure the power supply would not be interrupted.
3、 Make sure transmitter is fully powered.
"Receiver video
indicating LED
abnormal "
1、 Make sure video and audio signals can be transmitted
to receiver successfully.
2、 If there are video and audio signal on output devices,
please check the indicating LED to see if something got
wrong with it.
3、 Make sure the device is working within the supported
distance.
Bad picture
1、Ensure there is video on output devices.
2、Check if the receiver is correctly connected to display
equipment and there is no damage on joints and wires.
3、Make sure all devices are working on supported
distance. Draw them closer and try it again.
"No sound or
bad sound"
1、Restart the transmitter and connect it again
2、Make sure there is no disturbance from the same
frequency (4.9 ～ 5.9GHz) within 1 meter."
Other
problems
If any other problems occur, please restart the device
and make connections again.
8 Safety instructions
Keep this product away from metal furniture or explosive materials. Put it on
steady places and make sure there is no safety hazard around joints.
Do not use this product near water or on environments with a lot of dust.
Avoid exposing it on too low or too high temperatures.
Always use the DC power adaptors supplied, if there is a need of replacement
,ensure the alternatives have the same output rating of 5V 3A .
Do not let any heavy stuffs rest on this product. Ensure a proper ventilation is
provided at installation site. Never insert any objects into holes or ventilation
slots.
To save energy, please turn off the switches on the power adaptor leads or
unplug the power adaptor from the power sockets when the product is not
working.
Restart the device if it is damaged in any way or if it does not work normally.
And if it still cannot work, please power off and consult the dealer. Do not
open the equipment and repair it without authorization.
Cleaning：Turn off and unplug the product before performing any cleaning
and use only a lightly dampened soft cloth to wipe it. Do not use chemical
solvents or strong detergents as these may damage the surface.
● To prevent electric shock, do not remove any cover.
● Any maintenance should ask professionals for help.
● Do not expose this equipment to dripping or splashing.
● Never use this product near fire or any heat source.
● Do not let kids play with this product.
9 FCC & IC ID Warning
This device complies with Part 15 of the FCC Rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
Le présentappareilestconforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitationestautorisée aux deux
conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi,
mêmesi le brouillageest susceptible d'encompromettre le fonctionnement.
This equipment is portable device. The output power of this device is less than
20mW.
The SAR test is not required.
Declaration：W208 system is composed of two parts: transmitter and receiver.
Receiver has been tested to comply with FCC Part15.407 and IC rules. Test is
required for transmitter only.
-10--9-
Changes or modifications made to this equipment not expressly
approved by DFINE Technology Co., Ltd. may void the FCC authorization
to operate this equipment.