KS200/201/202 Touch Panel PC User’s Manual A23200228 1 Chapter 1 Introduction www.dfi.
Copyright FCC and DOC Statement on Class B This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
Table of Contents Copyright �������������������������������������������������������������������������������������������������������������2 Trademarks ��������������������������������������������������������������������������������������������������������2 FCC and DOC Statement on Class B ����������������������������������������������������� 2 About this Manual ������������������������������������������������������������������������������������������4 Warranty ������������������������������������������������
About this Manual Static Electricity Precautions An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click “User’s Manual” on the main menu. It is quite easy to inadvertently damage your PC, system board, components or devices even before installing them in your system unit.
Safety Precautions About the Package • Use the correct DC input voltage range. The package contains the following items. If any of these items are missing or damaged, please contact your dealer or sales representative for assistance. • Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord. • 1 • 1 • 3 • 1 • 1 • 1 • Danger of explosion if battery incorrectly replaced.
Chapter 1 Chapter 1 - Introduction Overview KS200 KS201 6 Chapter 1 Introduction www.dfi.
Chapter 1 KS202 Key Features • • • • TI® AM3517 Sitara ARM Cortex-A8 7" WVGA Touch Screen Fanless Panel PC 512MB DDR2 onboard 512MB NAND Flash onboard KS200 SD/MMC 1 SD/MMC card socket LAN 1 COM port COM 2 COM ports USB 2 Type A USB 2.0/1.1 ports GPIO 12-bit GPIO connector KS201 KS202 4 Customizable function keys Open Frame 7 Chapter 1 Introduction www.dfi.
Chapter 1 Specifications KS200 Processor System I/O Ports • TI® AM3517 Sitara ARM Cortex-A8 Memory • 512MB DDR2 onboard - 4 DDR2 64Mx16 RAM LCD and Touch Screen • 7” (800x480) WVGA TFT touch screen LCD • Supports touch screen - TI® TSC2004 touch screen controller • 400 NITS • 4-Wire Resistive type Storage • 1 SD/MMC card socket • 512MB NAND Flash - Samsung K9F4G08U0D flash memory 512Mx 8bit (512MB) • Front - 1 Power LED • Top - 1 SD/MMC card socket • Bottom - 12-bit GPIO (2 7-pole terminal blo
Chapter 1 Specifications KS201 Processor System Memory • 512MB DDR2 onboard - 4 DDR2 64Mx16 RAM LCD and Touch Screen • 7” (800x480) WVGA TFT touch screen LCD • Supports touch screen - TI® TSC2004 touch screen controller • 400 NITS • 4-Wire Resistive type Storage • 1 SD/MMC card socket • 512MB NAND Flash - Samsung K9F4G08U0D flash memory 512Mx 8bit (512MB) Ethernet I/O Ports • TI® AM3517 Sitara ARM Cortex-A8 • LAN8710 10/100Mbps LAN chip • 1 LAN port • Supports 10BASE-T and 100BASE-T Audio • 1
Chapter 1 Specifications KS202 Processor System I/O Ports • TI® AM3517 Sitara ARM Cortex-A8 Memory • 512MB DDR2 onboard - 4 DDR2 64Mx16 RAM LCD and Touch Screen • 7” (800x480) WVGA TFT touch screen LCD • Supports touch screen - TI® TSC2004 touch screen controller • 400 NITS • 4-Wire Resistive type Storage • 1 SD/MMC card socket • 512MB NAND Flash - Samsung K9F4G08U0D flash memory 512Mx 8bit (512MB) • Front - 1 Power LED • Top - 1 SD/MMC card socket • Bottom - 12-bit GPIO (2 7-pole terminal blo
Chapter 1 Getting to Know the KS200/201/202 Front View Bottom View RS232 COM Function Keys Line-Out 12-bit GPIO USB LAN 14-30V DC-in Power Switch RS232/422/485 COM COM Ports Used to connect serial devices. Power LED USB Ports Used to connect USB 2.0/1.1 devices. Power LED Indicates the power status of the system. LAN Port Used to connect the system to a local area network. Function Keys (KS201) Used to navigate through the pages. GPIO Supports 12-bit digital output and input.
Chapter 1 Mechanical Dimensions KS200 KS201 214.60 214.60 Top View Top View Left View 150.00 150.00 235.00 Right View 235.00 Left View Front View 40.80 Front View Right View 40.80 Bottom View Bottom View 12 Chapter 1 Introduction www.dfi.
Chapter 1 KS202 214.60 Top View Left View 95.00 90.00 190.00 Front View 11.20 35.80 75.00 75.00 93.40 (V,A FOR T/P) 133.00 90.00 20.99 4.49 142.32 65.85 20.20 92.04 (A,A FOR T/P) Ø3.50 125.60 230.40 221.00 190.00 154.40 (V,A FOR T/P) 153.00 (A,A FOR T/P) Right View 20.20 Bottom View 13 Chapter 1 Introduction www.dfi.
Chapter 2 Chapter 2 - Installation 2. Plug the terminal block into the DC-in connector and then tighten the screws to secure the terminal block in place. Connecting Cables to Terminal Blocks Important: DC-in connector When installing the touch panel PC, make sure the power is off. Failure to turn off, may cause severe damage to the system. Screws 1. Insert the cable end of the power adaptor to the terminal block.
Chapter 3 Chapter 3 - Ports and Connectors SD/MMC Top Panel I/O Port SD/MMC The front panel I/O port consist of the following: SD/MMC • 1 SD/MMC slot This expansion port is used to insert a Secure Digital (SD) or Multimedia Card (MMC) device. Aside from storing data files, an SD card is also capable of storing powerful software applications. 15 Chapter 3 Ports and Connectors www.dfi.
Chapter 3 GPIO Bottom Panel I/O Ports RS232 COM Line-Out 12-bit GPIO USB LAN 14-30V DC-in Power Switch RS232/422/485 COM 8 14 1 7 The bottom panel I/O ports consist of the following: • • • • • • 1 1 1 1 1 2 12-bit GPIO Line-Out jack RS232 COM port RS232/422/485 COM port LAN port USB ports The Digital I/O connector provides powering-on function to an external device that is connected to this connector.
Chapter 3 RS232 COM 1 Line-out COM 1: RS232 This jack is used to connect a headphone or external speakers. DCD RXD TXD DTR GND COM 1 is fixed at RS232. 12345 DSR RTS CTS RI 6 7 8 9 17 Chapter 3 Ports and Connectors www.dfi.
Chapter 3 RS232/422/485 COM 2 LAN Port COM 2: RS232/422/485 The LAN port allows the system board to connect to a local area network by means of a network hub. 6789 DATA+ DATAN.C. N.C. GND 6789 N.C. N.C. N.C. N.C. 1 2 34 5 DSR RTS CTS RI 1 2 34 5 12 345 6789 N.C. N.C. N.C. N.C. RX+ RXTX+ TXGND DCD RXD TXD DTR GND COM 2 18 Chapter 3 Ports and Connectors www.dfi.
Chapter 3 USB Ports USB 1-2 USB allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals. The system board is equipped with two onboard USB 2.0/1.1 ports (USB 1-2). 19 Chapter 3 Ports and Connectors www.dfi.
Chapter 4 Chapter 4 - Mounting Options 3. Attach the other bracket (wall mount bracket 2) to the rear of the Panel PC. Wall Mount The wall mount kit includes the following: Mounting screw • • Wall mount bracket 2 2 Wall mount brackets Bracket screws Hooks 4. Using the hooks on “bracket 2”, slide the Panel PC to “bracket 1”. Wall mount bracket 1 Wall mount bracket 2 Wall mount bracket 2 1. Select a place on the wall where you will mount the Panel PC. 2.
Panel Mount The panel mounting kit includes the following: • 6 mounting clamps 1. Select a place on the panel where you will mount the Panel PC. 2. Cut out a shape on the panel that corresponds to the Panel PC’s rear dimensions (217.6mm x 128.6mm). 128.60 21 7.6 0 3. Stick the poron foam on the rear panel. Poron foam Poron foam 21 Chapter 4 Mounting Options www.dfi.
Chapter 4 4. Slide the Panel PC through the hole until it is properly fitted against the panel. 5. Position the mounting clamps along the rear edges of the Panel PC, fitting them into the slits that are around the Panel PC. Mounting clamp 128.60 Slit for mounting the clamp 21 7.6 0 White plastic cap 6. The first and second clamps must be positioned and secured diagonally prior to mounting the rest of the clamps.
