CL630-CRM System Board User’s Manual A21720234
Copyright This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders. This publication is provided for informational purposes only.
FCC and DOC Statement on Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.
1 Introduction Table of Contents Copyright ........................................................................................... 2 Trademarks ........................................................................................ 2 FCC and DOC Statement on Class B .............................................. 3 About this Manual ............................................................................. 6 Warranty .................................................................................
Introduction 1 I/O Connectors ............................................................................ 45 S/PDIF Connector..................................................................... 45 Digital I/O Connectors .............................................................. 46 SATA (Serial ATA) Connectors .................................................... 47 Cooling Fan Connectors............................................................. 48 Chassis Instrusion Connector ....................
1 Introduction About this Manual An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click “User’s Manual” on the main menu. Warranty 6 1. Warranty does not cover damages or failures that arised from misuse of the product, inability to use the product, unauthorized replacement or alteration of components and product specifications. 2.
Introduction 1 Static Electricity Precautions It is quite easy to inadvertently damage your PC, system board, components or devices even before installing them in your system unit. Static electrical discharge can damage computer components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up. 1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are ready to install it. 2.
1 Introduction About the Package The system board package contains the following items. If any of these items are missing or damaged, please contact your dealer or sales representative for assistance.
Introduction 1 Chapter 1 - Introduction Specifications Processor • LGA 1155 socket for: Chipset • Intel® C216 Express chipset System Memory • Four 240-pin DDR3 DIMM sockets • Supports DDR3 1333/1600MHz (3rd generation processors) Supports DDR3 1066/1333MHz (2nd generation processors) • Supports dual channel memory interface • Supports up to 32GB system memory • DRAM device technologies: 1Gb, 2Gb and 4Gb DDR3 DRAM technologies are supported for x8 and x16 devices, unbuffered, ECC • 2 PCIe x16 slots -
1 Introduction LAN Serial ATA • Intel®® WG82579LM with iAMT8.0 Gigabit Ethernet Phy • Intel WG82574L PCI Express Gigabit Ethernet controller • Integrated 10/100/1000 transceiver • Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab • 6 Serial ATA ports - 2 SATA 3.0 ports with data transfer rate up to 6Gb/s - 4 SATA 2.
Introduction BIOS • AMI BIOS • 64Mbit SPI BIOS Energy Efficient Design • • • • Damage Free Intelligence • Monitors CPU/system temperature and overheat alarm • Monitors VCORE/5V/3.
1 Introduction Features Watchdog Timer The Watchdog Timer function allows your application to regularly “clear” the system at the set time interval. If the system hangs or fails to function, it will reset at the set time interval so that your system will continue to operate. DDR3 DDR3 delivers increased system bandwidth and improved performance. It offers peak data transfer rate of up to 21 Gb/s bandwidth.
Introduction 1 Serial ATA Serial ATA is a storage interface that is compliant with SATA 1.0a specification. SATA 3.0 supports speed up to 6Gb/s while SATA 2.0 supports speed up to 3Gb/s. This improves hard drive performance faster than the standard parallel ATA whose data transfer rate is 100MB/s. The board supports RAID 0/1/5/10. Gigabit LAN The Intel WG82579LM PHY and Intel WG82574L PCI Express Gigabit controllers support up to 1Gbps data transmission. USB The system board supports the new USB 3.0.
1 Introduction RTC Timer The RTC installed on the system board allows your system to automatically power-on on the set date and time. ACPI STR The system board is designed to meet the ACPI (Advanced Configuration and Power Interface) specification. ACPI has energy saving features that enables PCs to implement Power Management and Plug-and-Play with operating systems that support OS Direct Power Management. ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM function.
Hardware Installation 2 Chapter 2 - Hardware Installation System Board Layout COM 2 RS232/ Power select (JP7) PS2 KB/MS Power select (JP1) USB 8-9 Power 1 1 2 select (JP4) PS/2 KB/ MS USB 8-9 1 6 5 USB 2.
2 Hardware Installation Important: Electrostatic discharge (ESD) can damage your system board, processor, disk drives, add-in boards, and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis.
Hardware Installation 2 The system board supports the following memory interface. Single Channel (SC) Data will be accessed in chunks of 64 bits (8B) from the memory channels. Dual Channel (DC) Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides better system performance because it doubles the data transfer rate. Single Channel DIMMs are on the same channel. DIMMs in a channel can be identical or completely different.
2 Hardware Installation Installing the DIM Module Note: The system board used in the following illustrations may not resemble the actual board. These illustrations are for reference only. 1. Make sure the PC and all other peripheral devices connected to it has been powered down. 2. Disconnect all power cords and cables. 3. Locate the DIMM socket on the system board. 4. Push the “ejector tabs” which are at the ends of the socket to the side. Ejector tab Ejector tab 5.
Hardware Installation 6. Grasping the module by its edges, position the module above the socket with the “notch” in the module aligned with the “key” on the socket. The keying mechanism ensures the module can be plugged into the socket in only one way. 7. Seat the module vertically, pressing it down firmly until it is completely seated in the socket. 8. The ejector tabs at the ends of the socket will automatically snap into the locked position to hold the module in place.
2 Hardware Installation CPU The system board is equipped with a surface mount LGA 1155 socket. This socket is exclusively designed for installing a LGA 1155 packaged Intel CPU. Important: 1. Before you proceed, make sure (1) the LGA 1155 socket comes with a protective cap, (2) the cap is not damaged and (3) the socket’s contact pins are not bent. If the cap is missing or the cap and/or contact pins are damaged, contact your dealer immediately. 2. Make sure to keep the protective cap.
Hardware Installation 2 Installing the CPU 1. Make sure the PC and all other peripheral devices connected to it has been powered down. 2. Disconnect all power cords and cables. 3. Locate the LGA 1155 CPU socket on the system board. Important: The CPU socket must not come in contact with anything other than the CPU. Avoid unnecessary exposure. Remove the protective cap only when you are about to install the CPU. 4.
2 Hardware Installation 5. Lifting the load lever will at the same time lift the load plate. Lift the load lever up to the angle shown on the photo. 6. Load lever Load plate Remove the protective cap from the CPU socket. The cap is used to protect the CPU socket against dust and harmful particles. Remove the protective cap only when you are about to install the CPU.
Hardware Installation 7. 2 Insert the CPU into the socket. The gold triangular mark on the CPU must align with the corner of the CPU socket shown on the photo. Gold triangular mark The CPU’s notch will at the same time fit into the socket’s alignment key. Alignment key Important: The CPU will fit in only one orientation and can easily be inserted without exerting any force.
2 Hardware Installation 8. Close the load plate then push the load lever down. While closing the load plate, make sure the front edge of the load plate slides under the retention knob. 9. Hook the load lever under the retention tab.
Hardware Installation 2 Installing the Fan and Heat Sink The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circulation across the CPU and heat sink, the CPU will overheat damaging both the CPU and system board. Note: A boxed Intel® processor already includes the CPU fan and heat sink assembly. If your CPU was purchased separately, make sure to only use Intel®-certified fan and heat sink. 1.
2 Hardware Installation 4. Rotate each push-pin according to the direction of the arrow shown on top of the pin. Push down two pushpins that are diagonally across the heat sink. Perform the same procedure for the other two push-pins. Heat sink “Unlocked” position of push-pin “Locked” position of push-pin 5. 26 Connect the CPU fan’s cable to the CPU fan connector on the system board.
Hardware Installation 2 Jumper Settings Clear CMOS Data 1 2 3 JP12 1-2 On: Normal (default) 1 2 3 2-3 On: Clear CMOS Data If you encounter the following, a) CMOS data becomes corrupted. b) You forgot the supervisor or user password. you can reconfigure the system with the default values stored in the ROM BIOS. To load the default values stored in the ROM BIOS, please follow the steps below. 1. Power-off the system and unplug the power cord. 2. Set JP12 pins 2 and 3 to On.
2 Hardware Installation PS/2 Power Select JP1 1 2 3 1-2 On: +5V (default) 1 2 3 2-3 On: +5V_standby JP1 is used to select the power of the PS/2 keyboard and PS/2 mouse ports. Selecting +5V_standby will allow you to use the PS/2 keyboard or PS/2 mouse to wake up the system. Important: The +5VSB power source of your power supply must support ≥720mA.
Hardware Installation USB Power Select 2 USB 8-9 (JP4) 1 2 3 1-2 On: +5V (default) USB 0-1/2-3 (JP5) 1 2 3 2-3 On: +5V_standby 3 3 2 1 2 1 1-2 On: +5V 2-3 On: (default) +5V_standby 3 3 2 1 2 1 1-2 On: +5V 2-3 On: (default) +5V_standby USB 5-6 (JP11) USB 10-13 (JP9) 1 2 3 1-2 On: +5V (default) 1 2 3 2-3 On: +5V_standby These jumpers are used to select the power of the USB ports. Selecting +5V_standby will allow you to use a USB device to wake up the system.
2 Hardware Installation Power-on Select 1 2 3 JP13 1-2 On: Power-on via power button (default) 1 2 3 2-3 On: Power-on via AC power JP13 is used to select the method of powering on the system. If you want the system to power-on whenever AC power comes in, set JP13 pins 2 and 3 to On. If you want to use the power button, set pins 1 and 2 to On.
Hardware Installation 2 COM1/COM2 RS232/RS422/RS485 Select JP2 JP10 COM 1 COM 2 JP2 (for COM1) and JP10 (for COM2) are used to configure the COM ports to RS232, RS422 (Full Duplex) or RS485. The pin function of the COM ports will vary according to the jumper’s setting. JP2/JP10 2 4 6 1 3 5 1-2 On: RS232 (default) 2 4 6 2 4 1 3 5 1 3 5 3-4 On: RS422 Full Duplex 6 5-6 On: RS485 DCDRD TD DTRGND RXD+ RXDTXD+ TXDN.C. DATA+ DATAN.C. N.C. N.C.
2 Hardware Installation COM1/COM2 RS232/Power Select JP7 JP3 1 2 3 4 5 6 1-3 (RI), 2-4 (DCD) On: RS232 (default) 1 2 3 4 5 6 3-5 (+5V), 4-6 (+12V) On: RS232 with power 32
Hardware Installation 2 PCIE2 x4/ x1 Setting JP6 3 12 3 12 1 10 1 10 2-5-8-11, 3-6-9-12 On: PCIE2 signal from CPU (for x4 PCIe card) (default) 1-4-7-10, 2-5-8-11 On: PCIE2 signal from PCH (for x1 PCIe card) Note: 1. When JP6 is set to no signal, ignore JP8. (Supports Mini PCIe) If JP6 is set to x1, make sure JP8 is set to x1, too. (Mini PCIe not supported) 2. Use JP6’s default settings to avail the best configurations of the PCI Express slots.
2 Hardware Installation PCIE2/ Mini PCIe Setting JP8 3 12 3 12 1 10 1 10 1-4-7-10, 2-5-8-11 On: Mini PCIe slot (default) 2-5-8-11, 3-6-9-12 On: PCIE2 signal from PCH (for x1 PCIe card) Note: 1. When JP6 is set to no signal, ignore JP8. (Supports Mini PCIe) If JP6 is set to x1, make sure JP8 is set to x1, too. (Mini PCIe not supported) 2. Use JP8’s default settings to avail the best configurations of the PCI Express slots. However, not all processors provide 20 lanes of PCI Express bus.
Hardware Installation 2 Rear Panel I/O Ports PS/2 KB/MS COM DVI-I (DVI-D signal only) LAN LAN Line-in Line-out Mic-in USB 2.0 HDMI DVI-I USB 3.0 USB 3.
2 Hardware Installation PS/2 Mouse and PS/2 Keyboard Ports PS/2 Keyboard/Mouse These ports are used to connect a PS/2 mouse and a PS/2 keyboard. The PS/2 mouse port uses IRQ12. Wake-On-PS/2 Keyboard/Mouse The Wake-On-PS/2 Keyboard/Mouse function allows you to use the PS/2 keyboard or PS/2 mouse to power-on the system. To use this function: • Jumper Setting JP1 must be set to “2-3 On: +5V_standby”. Refer to “PS/2 Power Select” in this chapter for more information.
Hardware Installation 2 COM (Serial) Ports COM 2 COM 1 COM 1, COM2 : RS232/422/485 COM 3 to COM 6: RS232 2 1 COM 3 9 COM 5 COM 4 COM 6 COM 3 to COM 6 are fixed at RS232. The pin function of COM 1 and COM 2 ports will vary according to JP3/JP7’s setting. Refer to “COM1/COM2 RS232/RS422/RS485 Select” in this chapter for more information.
2 Hardware Installation HDMI Port HDMI The HDMI port which carries both digital audio and video signals is used to connect a LCD monitor or digital TV that has the HDMI port.
Hardware Installation 2 DVI-I Port DVI-I (DVI-D signal only) DVI-I The DVI-I port is used to connect an LCD monitor. This port supports DVI-D signal only. Connect the display device’s cable connector to the DVI-I port. After you plug the cable connector into the port, gently tighten the cable screws to hold the connector in place. BIOS Setting Configure the display device in the Chipset menu (“North Bridge Configuration” submenu) of the BIOS. Refer to chapter 3 for more information.
2 Hardware Installation RJ45 LAN Ports LAN 1 LAN 2 Features • Intel 82579LM with iAMT8.0 Gigabit Ethernet Phy • Intel 82574L PCI Express Gigabit Ethernet controller The LAN ports allow the system board to connect to a local area network by means of a network hub. BIOS Setting Configure the onboard LAN in the Chipset menu (“South Bridge Configuration” submenu) of the BIOS. Refer to chapter 3 for more information. Driver Installation Install the LAN drivers. Refer to chapter 4 for more information.
Hardware Installation 2 USB Ports USB 2.0 USB 9 USB 8 USB 1 USB 3.0 USB 3.0 USB 0 USB 3 USB 2 USB 2.0 GND +Data -Data VCC Key USB 12-13 USB 5-6 1 10 2 USB 10-11 N. C. GND +Data -Data VCC 9 USB allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals. The system board is equipped with four onboard USB 3.0/2.0/1.1 ports (USB 0-3) and two onboard USB 2.0/1.1 ports (USB 8-9).
2 Hardware Installation Driver Installation You may need to install the proper drivers in your operating system to use the USB device. Refer to your operating system’s manual or documentation for more information. Wake-On-USB Keyboard/Mouse The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse to wake up a system from the S3 (STR - Suspend To RAM) state. To use this function: • Jumper Setting JP4, JP5, JP9 and/or JP11 must be set to “2-3 On: 5V_standby”.
Hardware Installation 2 Audio Rear audio Mic-in Line-in Line2-R Mic2-R Mic2-L Front_IO_Sense Line2-L Line-out 9 10 Front audio GND Line2-JD Key Mic2-JD Presence Signal 1 2 Rear Audio The system board is equipped with 3 audio jacks. A jack is a one-hole connecting interface for inserting a plug. • Mic-in Jack (Light Blue) This jack is used to connect an external microphone.
2 Hardware Installation Front Audio The front audio connector allows you to connect to the second line-out and micin jacks that are at the front panel of your system. BIOS Setting Configure the onboard audio in the Chipset menu (“South Bridge” submenu) of the BIOS. Refer to chapter 3 for more information. Driver Installation Install the audio driver. Refer to chapter 4 for more information.
Hardware Installation 2 I/O Connectors S/PDIF Connector S/PDIF 1 5 SPDIF in Ground +5V Key SPDIF out The S/PDIF connector is used to connect an external S/PDIF port. Your S/PDIF port may be mounted on a card-edge bracket. Install the card-edge bracket to an available slot at the rear of the system chassis then connect the audio cable to the S/PDIF connector. Make sure pin 1 of the audio cable is aligned with pin 1 of the S/PDIF connector.
2 Hardware Installation Digital I/O Connectors 19 2 1 DIO The 8-bit Digital I/O connector provides powering-on function to external devices that are connected to these connectors.
Hardware Installation 2 SATA (Serial ATA) Connectors 1 GND RXP RXN GND TXN TXP GND 7 SATA 3.0 6Gb/s SATA 1 SATA 0 SATA 3 SATA 2 SATA 5 SATA 4 SATA 2.
2 Hardware Installation Cooling Fan Connectors CPU fan 4 1 Ground Speed Control Power Sense System fan_1 Ground Power Sense 1 3 1 3 System fan_2 Sense Ground Power The fan connectors are used to connect cooling fans. The cooling fans will provide adequate airflow throughout the chassis to prevent overheating the CPU and system board components. BIOS Setting The Advanced menu (“Hardware Health Configuration” submenu) of the BIOS will display the current speed of the cooling fans.
Hardware Installation 2 Chassis Intrusion Connector 1 2 Ground Chassis signal The board supports the chassis intrusion detection function. Connect the chassis intrusion sensor cable from the chassis to this connector. When the system’s power is on and a chassis intrusion occurred, an alarm will sound. When the system’s power is off and a chassis intrusion occurred, the alarm will sound only when the system restarts. MyGuard Hardware Monitor Install the “MyGuard Hardware Monitor” utility.
2 Hardware Installation Power Connectors 12 24 COM +3.3VDC +12VDC +5VDC +12VDC +5VDC +5VSB +5VDC NC PWR_OK COM COM +5VDC COM COM COM PS_ON# +5VDC COM COM -12VDC +3.3VDC +3.3VDC +3.3VDC 1 13 ATX power 8 4 Ground 12V 5 1 12V power Use a power supply that complies with the ATX12V Power Supply Design Guide Version 1.1. An ATX12V power supply unit has a standard 24-pin ATX main power connector that must be inserted into the 24-pin connector.
Hardware Installation 2 Standby Power LED Standby Power LED This LED will light red when the system is in the standby mode. It indicates that there is power on the system board. Power-off the PC and then unplug the power cord prior to installing any devices. Failure to do so will cause severe damage to the motherboard and components.
2 Hardware Installation Front Panel Connectors 1 2 PWR-LED HDD-LED PWR-BTN RESET-SW 11 12 HDD-LED - HDD LED This LED will light when the hard drive is being accessed. RESET SW - Reset Switch This switch allows you to reboot without having to power off the system. PWR-BTN - Power Switch This switch is used to power on or off the system. PWR-LED - Power/Standby LED When the system’s power is on, this LED will light.
Hardware Installation 2 Expansion Slots PCI Express x16 PCI Express x4 PCI Express x16 PCI 1 PCI 2 Mini PCI Express PCI 3 PCI Express x16 Slot Install PCI Express x16 graphics card, that comply to the PCI Express specifications, into the PCI Express x16 slot. To install a graphics card into the x16 slot, align the graphics card above the slot then press it down firmly until it is completely seated in the slot. The retaining clip of the slot will automatically hold the graphics card in place.
2 Hardware Installation CD-in Internal Audio Connector 4 Right audio channel Ground Ground Left audio channel 1 The CD-in connector is used to receive audio from a CD-ROM drive, TV tuner or MPEG card.
Hardware Installation 2 IDE Connector 2 1 40 39 The IDE connector is used to connect hard drives. The connector on the IDE cable can be inserted into this connector only if pin 1 of the cable is aligned with pin 1 of this connector. The IDE connector supports 2 devices, a Master and a Slave. Use an IDE ribbon cable to connect the drives to the system board. An IDE ribbon cable has 3 connectors on them, one that plugs into the IDE connector on the system board and the other 2 connects to IDE devices.
2 Hardware Installation Note: Refer to your disk drive user’s manual for information about selecting proper drive switch settings. Adding a Second IDE Disk Drive When using two IDE drives, one must be set as the master and the other as the slave. Follow the instructions provided by the drive manufacturer for setting the jumpers and/or switches on the drives. The system board supports Enhanced IDE or ATA-2, ATA/33, ATA/66, ATA/100 and ATA/133 hard drives.
Hardware Installation 2 Battery Battery The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source of power when the main power is shut off. Safety Measures • Danger of explosion if battery incorrectly replaced. • Replace only with the same or equivalent type recommend by the manufacturer. • Dispose of used batteries according to local ordinance.
3 BIOS Setup Chapter 3 - BIOS Setup Overview The BIOS is a program that takes care of the basic level of communication between the CPU and peripherals. It contains codes for various advanced features found in this system board. The BIOS allows you to configure the system and save the configuration in a battery-backed CMOS so that the data retains even when the power is off.
BIOS Setup 3 Legends Keys Function Right and Left arrows Moves the highlight left or right to select a menu. Up and Down arrows Moves the highlight up or down between submenus or fields. Exits to the BIOS Setup Utility. + (plus key) Scrolls forward through the values or options of the highlighted field. - (minus key) Scrolls backward through the values or options of the highlighted field. Tab Selects a field. Displays General Help. Saves and exits the Setup program.
3 BIOS Setup AMI BIOS Setup Utility Main The Main menu is the first screen that you will see when you enter the BIOS Setup Utility. Main Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Event & Log Boot Security Save & Exit Chipset BIOS Information BIOS Vendor Core Version Compliancy Project Version Build Date and Time American Megatrends 4.6.5.3 UEFI 2.3; PI 1.2 1APTJ 0.
BIOS Setup 3 Advanced The Advanced menu allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference. Important: Setting incorrect field values may cause the system to malfunction. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
3 BIOS Setup ACPI Power Management Configuration This section is used to configure the ACPI Power Management. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced ACPI Power Management Configuration ACPI Sleep State S3 Video Repost Resume by PME Resume by Ring Resume by USB Resume by PS2 KB (S1,S3) Resume by PS2 MS (S1,S3) [S3 only(Suspend to ....
BIOS Setup 3 Resume by PS2 KB (S1, S3) About resume by PS2 KB (S1, S3); Options are enabled or disabled. Resume by PS2 MS (S1, S3) About resume by PS2 MS (S1, S3); Options are enabled or disabled. Wake system with Fixed Time Enable or disable the system wake on alarm event. When enabled, system will wake on the hr::min::sec specified.
3 BIOS Setup PC Health Status This section displays the SIO hardware health monitor. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Smart Fan Function System Hardware Monitor Smart Fan Function Case Open Beep [Disabled] CPU Temperature System Temperature CPU FAN Speed System FAN Speed System FAN2 Speed VCore +5.0V +12V VDIMM +3.3V VS5V : : : : : : : : : : : +40 C +26 C 2946 RPM N/A N/A +1.080V +5.032 V +12.320V +1.536 V +3.376 V +5.
BIOS Setup 3 CPU Smart Fan Control When this feature is set to Automatic, the CPU’s fan speed will rotate according to the CPU’s temperature. The higher the temperature, the faster the speed of rotation. Boundary 1 to Boundary 4 The range is from 0-127. Speed Count 1 to Speed Count 5 The range is from 1-100. Case Open Beep Set this field to Enabled to allow the system to alert you of a chassis intrusion event.
3 BIOS Setup Trusted Computing (optional) This section configures settings relevant to Trusted Computing innovations. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Configuration TPM Support [Disabled] Current Status Information No Security Device Found Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. Select Screen Select Item Enter: Select +/-: Change Opt.
BIOS Setup 3 CPU Configuration This section is used to configure the CPU. It will also display the detected CPU information. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced CPU Configuration Intel (R) Core (TM) i3-3220 CPU @ 3.
3 BIOS Setup Intel Virtualization Technology When this field is set to Enabled, the VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.
BIOS Setup 3 SATA Configuration This section is used to configure SATA functions. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
3 BIOS Setup If AHCI or RAID is selected in the SATA Mode Selection, it will display the following information: SATA Controller(s) SATA Mode Selection [Enabled] [AHCI] Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Determines how SATA controller(s) operate.
BIOS Setup 3 Intel TXT (LT) Configuration This section is used to configure the Intel Trusted Execution technology. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Intel Trusted Execution Technology Configuration Intel TXT support only can be enabled/disabled if SMX is enabled. VT and VT-d support must also be enabled prior to TXT. Secure Mode Extension (SMX) Disabled Intel TXT(LT) Support [Disabled] Select Screen Select Item Enter: Select +/-: Change Opt.
3 BIOS Setup Intel AMT Configuration Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced [Enabled] [Disabled] Intel AMT Disable ME Enable/ Disable Intel (R) Active Management Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires addition firmware in the SPI device. Select Screen Select Item Enter: Select +/-: Change Opt.
BIOS Setup 3 USB Configuration This section is used to configure USB. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced USB Configuration USB Devices: 2 Hubs Legacy USB Support XHCI Hand-off EHCI Hand-off Port 60/64 Emulation [Enabled] [Enabled] [Disabled] [Enabled] USB hardware delayss and time-outs: Device power-up delay [Auto] Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected.
3 BIOS Setup F81217 Second Super IO Configuration This section is used to configure the serial port functions. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Set Parameters of Serial Port 0 (COMA) F81217 Second Super IO Configuration F81217 Second Super IO Chip Port 3 Configuration Port 4 Configuration Port 5 Configuration Port 6 Configuration Serial Serial Serial Serial F81217 Second IO Select Screen Select Item Enter: Select +/-: Change Opt.
BIOS Setup 3 F71879 Super IO Configuration This section is used to configure the I/O functions supported by the onboard Super I/O chip. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Restore AC Power Loss help.
3 BIOS Setup Serial Port 0 Configuration to Serial Port 1 Configuration Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Serial Port 0 Configuration Serial Port Device Settings [Enabled] IO=3F8h; IRQ=4; Change Settings [Auto] Enable or Disable Serial Port (COM) Select Screen Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
BIOS Setup 3 JMB36X ATA Controller Configuration This section is used to configure the serial port functions. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced PATA Primary Master PATA Primary Slave Not Present Not Present JMB 368 ATA Controller [IDE Mode] Select an operative mode for ATA controller Select Screen Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219.
3 BIOS Setup Chipset Configures relevant chipset functions. Main Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Event & Log Chipset Boot Security Save & Exit PCH-IO Configuration System Agent (SA) Configuration PCH Parameters Select Screen Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
BIOS Setup 3 PCH-IO Configuration Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Chipset Intel PCH RC Version Intel PCH SKU Name Intel PCH Rev ID USB PCH 1.1.0.0 C216 04/C1 USB Coniguration settings. Configuration Azalia Configuration PCH LAN Controller Wake on LAN [Enabled] [Enabled] Select Screen Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219.
3 BIOS Setup USB Configuration Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Chipset Enable or disable XHCI pre-boot driver support. USB Configuration XHCI Pre-Boot Driver xHCI Mode [Enabled] [Smart Auto] EHCI1 [Enabled] EHCI2 [Enabled] Select Screen Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
BIOS Setup 3 System Agent (SA) Configuration Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Chipset System Agent Bridge Name System Agent RC Version VT-d Capability IvyBridge 1.1.0.0 unsupported Config Graphics Settings. Graphics Configuration NB PCIe Configuration Memory Configuration Select Screen Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219.
3 BIOS Setup Internal Graphics Keep IGD enabled based on the setup options. DVMT Pre-Allocated Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the internal graphics device. DVMT Total Gfx Memory Select DVMT 5.0 total Graphics Memory size used by the internal graphics device. Gfx low power mode This option is applicable for SFF only. Grafics Performance Analyzers Enable or Disabel Intel Grafics Performance Analyzers Counters.
BIOS Setup 3 NB PCIe Configuration Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Chipset NB PCIe Configuration PEG0 PEG0 - Gen X PEG0 ASPM PEG3 PEG3 - Gen X PEG3 ASPM Not Present [Auto] [Auto] Not Present [Auto] [Auto] Configure PEG B0:D1:F0 Gen1-Gen3 Select Screen Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
3 BIOS Setup Memory Information Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Chipset Memory Information Memory RC Version Memory Frequency Total Memory DIMM#0 DIMM#1 DIMM#2 DIMM#3 CAS Latency (tCL) Minimum delay time CAS to RAS (tRCDmin) ROW precharge (tRPmin) Active to Precharge (tRASmin) XMP Profile 1 XMP Profile 2 1.1.0.
BIOS Setup 3 Boot Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Chipset Security Save & Exit Event & Log Boot Advanced Main Boot Configuration Setup Prompt Timeout Bootup NumLock State 1 [On] Quiet Boot Fast Boot [Disabled] [Disabled] CSM16 Module Version 07.69 GateA20 Active Option ROM Messages INT19 Trap Response [Upon Request] [Force BIOS] [Immediate] Boot Option Priorities CSM Parameters Number of seconds to wait for setup activation key.
3 BIOS Setup Option ROM Messages Set display mode for option ROM. Int19 Trap Response BIOS reaction on Int19 trapping by option ROM. CSM Parameters Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Boot Launch CSM Boot Option Filter Launch PXE OpROM policy Launch Storage OpROM policy Launch Video OpROM policy [Always] [UEFI and Legancy] [Do not launch] [Legacy only] [Legacy only] This option controls if CSM will be launched.
BIOS Setup 3 Security Main Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Save & Exit Event & Log Chipset Boot Security Advanced Password Description If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights.
3 BIOS Setup Save & Exit Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Event & Log Reset the system after saving the changes. Save Options Save Changes Discard Changes Restore Defaults Save as User Defaults Restore User Defaults Boot Override Launch EFI Shell from filesystem device Select Screen Select Item Enter: Select +/-: Change Opt.
BIOS Setup 3 Event & Log Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Main Change Advanced Chipset Boot Security Save & Exit Smbios Event Log Settings View Smbios Event Log View System Event Log Event & Log Press to change the Smbios Event Log Configuration. Select Screen Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219.
3 BIOS Setup Change Smbios Event Log Settings Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Event & Log Enabling/Disabling Options Smbios Event Log [Enabled] Erasing Settings Erase Event Log When Log is Full [No] [Do nothing] Smbios Event Log Standard Settings Log System Boot Event MECI METW [Enabled] 1 60 Custom Options Log OEM Codes Convert OEM Codes [Enabled] [Disabled] Note: All values changed here do not take effect until computer is restarted.
BIOS Setup 3 Log OEM Codes Enable or disable the logging of EFI Status Codes as OEM Codes (if not already converted to legacy). Convert OEM Codes Enable or disable the converting of EFI Status Codes to Standard Smbios Types (Not all may be translated).
3 BIOS Setup Updating the BIOS To update the BIOS, you will need the new BIOS file and a flash utility, AFUDOS. EXE. Please contact technical support or your sales representative for the files. To execute the utility, type: A:> AFUDOS BIOS_File_Name /b /p /n then press . C:\AFU\AFUDOS>afudos filename /B /P /N +--------------------------------------------------------------------------------------------------------+ | AMI Firmware Update Utility(APTIO) v2.
Supported Software 4 Chapter 4 - Supported Software The CD that came with the system board contains drivers, utilities and software applications required to enhance the performance of the system board. Insert the CD into a CD-ROM drive. The autorun screen (Mainboard Utility CD) will appear. If after inserting the CD, “Autorun” did not automatically start (which is, the Mainboard Utility CD screen did not appear), please go directly to the root directory of the CD and double-click “Setup”.
4 Supported Software Auto Run Pages (for Windows 7) 94
Supported Software 4 Microsoft .NET Framework 3.5 (for Windows XP only) Note: Before installing Microsoft .NET Framework 3.5, make sure you have updated your Windows XP operating system to Service Pack 3. To install the driver, click “Microsoft .NET Framework 3.5” on the main menu. 1. Read the license agreement carefully. Click “I have read and accept the terms of the License Agreement” then click Install. 2. Setup is now installing the driver.
4 Supported Software 3. 96 Click Exit.
Supported Software 4 Intel Chipset Software Installation Utility The Intel Chipset Software Installation Utility is used for updating Windows INF files so that the Intel chipset can be recognized and configured properly in the system. To install the utility, click “Intel Chipset Software Installation Utility” on the main menu. 1. Setup is ready to install the utility. Click Next. 2. Read the license agreement then click Yes.
4 98 Supported Software 3. Go through the readme document for more installation tips then click Next. 4. Click Finish to exit setup.
Supported Software 4 Microsoft DirectX 9.0C (for Windows XP only) To install the driver, click “Microsoft DirectX 9.0C” on the main menu. 1. Click “I accept the agreement” then click Next. 2. To start installation, click Next. 3. Click Finish. Reboot the system for DirectX to take effect.
4 Supported Software Intel Graphics Drivers (for Windows 7) To install the driver, click “Intel Graphics Drivers” on the main menu. 1. Setup is now ready to install the graphics driver. Click Next. By default, the “Automatically run WinSAT and enable the Windows Aero desktop theme” is enabled. With this enabled, after installing the graphics driver and the system rebooted, the screen will turn blank for 1 to 2 minutes (while WinSAT is running) before the Windows Vista desktop appears.
Supported Software 3. Go through the readme document for system requirements and installation tips then click Next. 4. Setup is now installing the driver. Click Next to continue. 5. Click “Yes, I want to restart this computer now” then click Finish. 4 Restarting the system will allow the new software installation to take effect.
4 Supported Software Intel Graphics Drivers (for Windows XP) To install the driver, click “Intel Graphics Drivers” on the main menu. 102 1. Setup is ready to install the graphics driver. Click Next. 2. Read the license agreement then click Yes. 3. Go through the readme document for more installation tips then click Next.
Supported Software 4. Setup is currently installing the driver. After installation has completed, click Next. 5. Click “Yes, I want to restart this computer now.” then click Finish. 4 Restarting the system will allow the new software installlation to take effect.
4 Supported Software Audio Drivers To install the driver, click “Audio Drivers” on the main menu. 1. Setup is ready to install the driver. Click Next. 2. Click “Yes, I want to restart my computer now” then click Finish. Restarting the system will allow the new software installation to take effect.
Supported Software 4 Intel LAN Drivers To install the driver, click “Intel LAN Drivers” on the main menu. 1. Setup is ready to install the driver. Click Next. 2. Click “I accept the terms in the license agreement” then click “Next”. 3. Select the program featuers you want installed then click Next.
4 106 Supported Software 4. Click Install to begin the installation. 5. After completing installation, click Finish.
Supported Software 4 Intel USB 3.0 (for Windows 7 only) To install the driver, click “Intel USB 3.0” on the main menu. 1. Setup is ready to install the graphics driver. Click Next. 2. Read the license agreement then click Yes. 3. Go through the readme document for more installation tips then click Next.
4 108 Supported Software 4. Setup is currently installing the driver. After installation has completed, click Next. 5. After completing installation, click Finish.
Supported Software 4 Intel Management Engine Drivers To install the driver, click “Intel Management Engine Driver” on the main menu. 1. Setup is ready to install the driver. Click Next. 2. Read the license agreement then click Yes.
4 110 Supported Software 3. Setup is currently installing the driver. After installation has completed, click Next. 4. After completing installation, click Finish.
Supported Software 4 MyGuard Hardware Monitor 1. Locate for the MyGuard folder in the provided disc. 2. In the MyGuard folder, right-click on the “setup” file. 3. Select Run As Administrator. 4. Double-click Setup. Important: Perform steps 1-3 only when using Windows 7 or Windows Vista. 5. Setup is ready to install the utility. Click Next. 6. Click Install to begin installation.
4 112 Supported Software 7. Setup is currently installing the utility. 8. After completing installation, click Finish to exit setup.
Supported Software 4 Intel Rapid Storage Drivers To install the driver, click “Intel Rapid Storage Drivers” on the main menu. Note: Windows Vista is not supported. 1. Setup is ready to install the driver. Click Next. 2. Read the license agreement then click Yes.
4 Supported Software 3. Go through the readme document for more installation tips then click Next. 4. Setup is currently installing the driver. After installation has completed, click Next. 5. Click “Yes, I want to restart this computer now.” then click Finish. Restarting the system will allow the new software installlation to take effect.
Supported Software 4 F6 Floppy This is used to create a floppy driver diskette needed when you install Windows® XP using the F6 installation method. This will allow you to install the operating system onto a hard drive when in AHCI mode. 1. Insert a blank floppy diskette. 2. Locate for the drivers in the CD then copy them to the floppy diskette. The CD includes drivers for both 32-bit and 64-bit operating systems. The path to the drivers are shown below.
4 Supported Software Infineon TPM Driver and Tool (optional) To install the driver, click “Infineon TPM driver and tool (option)” on the main menu. 116 1. TPM requires installing the Microsoft Visual C++ package prior to installing the driver. Click Install. 2. The setup program is preparing to install the driver. 3. The setup program is ready to install the driver. Click Next.
Supported Software 4. Click “I accept the terms in the license agreement” and then click “Next”. 5. Enter the necessary information and then click Next. 6. Select a setup type and then click Next.
4 118 Supported Software 7. Click Install. 8. The setup program is currently installing the driver. 9. Click Finish.
Supported Software 10. 4 Click Yes to restart the system. Restarting the system will allow the new software installation to take effect.
4 Supported Software Adobe Acrobat Reader 9.3 To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu. 120 1. Click Next to install or click Change Destination Folder to select another folder. 2. Click Install to begin installation. 3. Click Finish to exit installation.
RAID 5 Chapter 5 - RAID The system board allows configuring RAID on Serial ATA drives. It supports RAID 0, RAID 1, RAID 5 and RAID 10. RAID Levels RAID 0 (Striped Disk Array without Fault Tolerance) RAID 0 uses two new identical hard disk drives to read and write data in parallel, interleaved stacks. Data is divided into stripes and each stripe is written alternately between two disk drives. This improves the I/O performance of the drives at different channel; however it is not fault tolerant.
5 RAID Settings To enable the RAID function, the following settings are required. 1. Connect the Serial ATA drives. 2. Configure Serial ATA in the AMI BIOS. 3. Configure RAID in the RAID BIOS. 4. Install the RAID driver during OS installation. 5. Install the Intel Rapid Storage Drivers. Step 1: Connect the Serial ATA Drives Refer to chapter 2 for details on connecting the Serial ATA drives. Important: 1.
RAID 5 Step 4: Install the RAID Driver During OS Installation The RAID driver must be installed during the Windows® XP or Windows® 2000 installation using the F6 installation method. This is required in order to install the operating system onto a hard drive or RAID volume when in RAID mode or onto a hard drive when in AHCI mode. 1. Start Windows Setup by booting from the installation CD. 2.
5 RAID Step 5: Install the Intel Rapid Storage Technology Utility The Intel Rapid Storage Technology Utility can be installed from within Windows. It allows RAID volume management (create, delete, migrate) from within the operating system. It will also display useful SATA device and RAID volume information. The user interface, tray icon service and monitor service allow you to monitor the current status of the RAID volume and/or SATA drives.
RAID 5. Read the license agreement then click Yes. 6. Go through the readme document to view system requirements and installation information then click Next. 7. Click “Yes, I want to restart my computer now” then click Finish.
6 Intel AMT Settings Chapter 6 - Intel AMT Settings Overview Intel Active Management Technology (Intel® AMT) combines hardware and software solution to provide maximum system defense and protection to networked systems. The hardware and software information are stored in non-volatile memory. With its built-in manageability and latest security applications, Intel® AMT provides the following functions.
Intel AMT Settings 6 Enable Intel® AMT in the AMI BIOS 1. Power-on the system then press to enter the main menu of the AMI BIOS. 2. In the Advanced menu, select AMT Configuration. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
6 Intel AMT Settings 4. In the Save & Exit menu, select Save Changes and Reset then select OK. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Save Changes and Reset Discard Changes and Reset Security Save & Exit Reset the system after saving the changes.
Intel AMT Settings 6 Enable Intel ® AMT in the Intel ® Management Engine BIOS Extension (MEBX) Screen 1. When the system reboots, the following message will be displayed. Press as soon as the message is displayed; as this message will be displayed for only a few seconds. American Megatrends Version 2. 14. 1219. Copyright (C) 2011 American Megatrends, Inc. BIOS Date: 02/17/2012 18:13:29 Ver: 1APTJ Press to enter MEBS setup menu Press or to enter setup 2.
6 Intel AMT Settings 3. Enter a new password in the space provided under Intel(R) ME New Password then press Enter. The password must include: • • • • • 8-32 characters Strong 7-bit ASCII characters excluding : , and ” characters At least one digit character (0, 1, ...9) At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;) Both lower case and upper case characters Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.
Intel AMT Settings 4. 6 You will be asked to verify the password. Enter the same new password in the space provided under Verify Password then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. Main Menu MEBx Login > Intel (R) ME General Settings > Intel (R) AMT Configuration MEBx Exit Verify Password Intel (R) ME Password [] = Move highlight 5.
6 Intel AMT Settings 6. Select Change Intel(R) ME Password then press Enter. You will be prompted for a password. The default password is “admin”. Enter the default password in the space provided under Intel(R) ME New Password then press Enter. • • • • • 8-32 characters Strong 7-bit ASCII characters excluding : , and ” characters At least one digit character (0, 1, ...9) At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g.
Intel AMT Settings 7. 6 Select Local FW Update then press Enter. Select Enabled then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. INTEL (R) ME PLATFORM CONFIGURATION > Change ME Password Local FW Updtate > Power Control Disabled Enabled Password Protected = Complete Entry 8.
6 Intel AMT Settings 9. In the Intel(R) ME Power Control menu, select Intel(R) ME ON in Host Sleep States then press Enter. Select an option then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
Intel AMT Settings 11. 6 Select Previous Menu until you return to the Main Menu. Select Intel(R) AMT Configuration then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. INTEL (R) AMT CONFIGURATION Manageability Feature Selection > SOL/ IDER/ KVM > User Consent Password Policy > Network Setup Activate Netwok Access Unconfigure Network Access > Remote Setup And Configuration [] = Move highlight 12.
6 Intel AMT Settings 13. In the Intel(R) AMT Configuration menu, select SOL/IDER/KVM then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. SOL/ IDER/ KVM Username and password SOL IDER KVM Feature Selection Legacy Redirection Mode < Enabled> Menu for FW Redirection Configuration [] = Move highlight 14.
Intel AMT Settings 15. 6 In the SOL/IDER/KVM menu, select SOL then press Enter. Select disabled then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. SOL/ IDER/ KVM Username and password SOL IDER KVM Feature Selection Legacy Redirection Mode < Enabled> Disabled Enabled = Complete Entry 16.
6 Intel AMT Settings 17. In the SOL/IDER/KVM menu, select KVM then press Enter. Select disabled then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. SOL/ IDER/ KVM Username and password SOL IDER KVM Feature Selection Legacy Redirection Mode < Enabled> Disabled Enabled = Complete Entry 18.
Intel AMT Settings 19. 6 Select Enabled then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. SOL/ IDER/ KVM Username and password SOL IDER KVM Feature Selection Legacy Redirection Mode < Enabled> Disabled Enabled = Complete Entry 20. [ESC]= Discard Changes Select Previous Menu until you return to the Intel(R) AMT Configuration menu.
6 Intel AMT Settings 21. In the User Consent Configuration menu, select User Opt-in then press Enter. Select None then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. USER CONSENT User Opt-in Opt-in Configuration from Remote IT < KVM> < Enabled> NONE KVM ALL = Complete Entry 22.
Intel AMT Settings 23. 6 Select Previous Menu until you return to the Intel(R) AMT Configuration menu. Select Password Policy then press Enter. You may choose to use a password only during setup and configuration or to use a password anytime the system is being accessed. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
6 Intel AMT Settings 25. In the Intel(R) Network Setup menu, select Intel(R) ME Network Name Settings then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. INTEL (R) ME NETWORK SETUP > Intel (R) ME Network Name Settings > TCP/ IP Settings [] = Move highlight 26. [ENTER] = Select Entry [ESC]= Exit In the Intel(R) ME Network Name Settings menu, select Host Name then press Enter.
Intel AMT Settings 27. 6 Select Domain Name then press Enter. Enter the computer’s domain name then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. INTEL (R) ME NETWORK NAME SETTINGS Host Name Domain Name Shared/ Dedicated FQDN Dynamic DNS Update _ _ Computer Domain Name = Complete Entry 28. [ESC]= Discard Changes Select Shared/Dedicated FQDN then press Enter.
6 Intel AMT Settings 29. Select Dynamic DNS Update then press Enter. Select Enabled or Disabled then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. INTEL (R) ME NETWORK NAME SETTINGS Host Name Domain Name Shared/ Dedicated FQDN Dynamic DNS Update _ _ Disabled Enabled = Complete Entry 30.
Intel AMT Settings 31. 6 In the TCP/IP Settings menu, select Wired LAN IPV4 Configuration then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. WIRED LAN IPV4 CONFIGURATION DHCP Mode Disabled Enabled = Complete Entry 32. [ESC]= Discard Changes Select Previous Menu until you return to the Intel(R) AMT Configuration menu. Select Activate Network Access then press Enter.
6 Intel AMT Settings 33. In the Intel(R) AMT Configuration menu, select Unconfigure Network Access then press Enter. Type Y then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
Intel AMT Settings 35. 6 In the Intel(R) Automated Setup And Configuration menu, select Current Provisioning Mode then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. INTEL (R) AUTOMATED SETUP AND CONFIGURATION Current Provisioning Mode Provisioning Record Provisioning Server IPV4/IPV6 _ Provisioning Server FQDN _ > RCFG > TLS PSK Provisioning Mode:PKI > TLS PKI [] = Move highlight 36.
6 Intel AMT Settings 37. Select Previous Menu until you return to the Intel(R) Automated Setup And Configuration menu. Select Provisioning Server IPV4/IPV6 then press Enter. Type server address then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
Intel AMT Settings 39. 6 In the Intel(R) Remote Configuration menu, select Start Configuration then press Enter. Type Y then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. INTEL (R) REMOTE CONFIGURATION Start Configuration This will activate Remote Configuration. Continue: (Y/N) [ESC] = Exit [] = Move highlight 40.
6 Intel AMT Settings 41. In the Intel(R) Remote Configuration menu, select Set PID and PPS ** then press Enter. Type PID code then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. INTEL (R) TLS PSK CONFIGURATION Set PID and PPS ** Delete PID and PPS ** _ Enter PID (e.g. ABCD-1234) = Complete Entry 42.
Intel AMT Settings 43. 6 Select Previous Menu until you return to the Intel(R) Automated Setup And Configuration menu. Select TLS PKI then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. INTEL (R) AUTOMATED SETUP AND CONFIGURATION Current Provisioning Mode Provisioning Record Provisioning Server IPV4/IPV6 Provisioning Server FQDN > RCFG > TLS PSK > TLS PKI [] = Move highlight 44.
6 Intel AMT Settings 45. In the Intel(R) Remote Configuration menu, select PKI DNS Suffix then press Enter. Type PKI DNS Suffix then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. INTEL (R) REMOTE CONFIGURATION Remote Configuration ** PKI DNS Suffix > Manage Hashes _ Enter PKI DNS Suffix = Complete Entry 46.
Intel AMT Settings 47. 6 Select Previous Menu until you return to the Main Menu. Select Exit then press Enter. Type Y then press Enter. Intel(R) Management Engine BIOS Extension v8.0.0.0061/Intel(R) ME v8.0.4.1441 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
A NLITE and AHCI Installation Guide Appendix A - NLITE and AHCI Installation Guide nLite nLite is an application program that allows you to customize your XP installation disc by integrating the RAID/AHCI drivers into the disc. By using nLite, the F6 function key usually required during installation is no longer needed. Note: The installation steps below are based on nLite version 1.4.9. Installation procedures may slightly vary if you’re using another version of the program. 1.
NLITE and AHCI Installation Guide 4. Insert the XP installation disc into an optical drive. 5. Launch nLite. The Welcome screen will appear. Click Next. 6. Click Next to temporarily save the Windows installation files to the designated default folder. A If you want to save them in another folder, click Browse, select the folder and then click Next.
A 156 NLITE and AHCI Installation Guide 7. Click Next. 8. In the Task Selection dialog box, click Drivers and Bootable ISO. Click Next.
NLITE and AHCI Installation Guide 9. 10. A Click Insert and then select Multiple driver folder to select the drivers you will integrate. Click Next. Select only the drivers appropriate for the Windows version that you are using and then click OK. Integrating 64-bit drivers into 32-bit Windows or vice versa will cause file load errors and failed installation.
A 158 NLITE and AHCI Installation Guide 11. If you are uncertain of the southbridge chip used on your motherboard, select all RAID/AHCI controllers and then click OK. 12. Click Next.
NLITE and AHCI Installation Guide 13. The program is currently integrating the drivers and applying changes to the installation. 14. When the program is finished applying the changes, click Next.
A NLITE and AHCI Installation Guide 15. To create an image, select the Create Image mode under the General section and then click Next. 16. Or you can choose to burn it directly to a disc by selecting the Direct Burn mode under the General section. Select the optical device and all other necessary settings and then click Next.
NLITE and AHCI Installation Guide 17. A You have finished customizing the Windows XP installation disc. Click Finish. Enter the BIOS utility to configure the SATA controller to RAID/AHCI. You can now install Windows XP.
A NLITE and AHCI Installation Guide AHCI The installation steps below will guide you in configuring your SATA drive to AHCI mode. 1. Enter the BIOS utility and configure the SATA controller to IDE mode. 2. Install Windows XP but do not press F6. 3. Download relevant RAID/AHCI driver files supported by the motherboard chipset from Intel’s website. Transfer the downloaded driver files to C:\AHCI. 4.
NLITE and AHCI Installation Guide 5. In the Hardware Update Wizard dialog box, select “No, not this time” then click Next. 6. Select “Install from a list or specific location (Advanced)” and then click Next. 7. Select “Don’t search. I will choose the driver to install” and then click Next.
A NLITE and AHCI Installation Guide 8. Click “Have Disk”. 9. Select C:\AHCI\iaAHCI.inf and then click Open. 10. 164 Select the appropriate AHCI Controller of your hardware device and then click Next.
NLITE and AHCI Installation Guide 11. A A warning message appeared because the selected SATA controller did not match your hardware device. Ignore the warning and click Yes to proceed. 12. Click Finish. 13. The system’s settings have been changed. Windows XP requires that you restart the computer. Click Yes. 14. Enter the BIOS utility and modify the SATA controller from IDE to AHCI. By doing so, Windows will work normally with the SATA controller that is in AHCI mode.
B Watchdog Timer Appendix B - Watchdog Sample Code ;Software programming example: ;--------------------------------------------;(1) Enter Super IO Configuration mode ;--------------------------------------------MOV DX,2EH MOV AL,87H OUT DX,AL OUT DX,AL ;------------------------------------------------------------------------------------------;(2) Configuration Logical Device 7, register CRF5/CRF6 (WDT Control /WDT timer) ;------------------------------------------------------------------------------------
System Error Message C Appendix C - System Error Message When the BIOS encounters an error that requires the user to correct something, either a beep code will sound or a message will be displayed in a box in the middle of the screen and the message, PRESS F1 TO CONTINUE, CTRL-ALT-ESC or DEL TO ENTER SETUP, will be shown in the information box at the bottom. Enter Setup to correct the error.
C System Error Message Hard Disk(s) fail (20) HDD initialization error. Hard Disk(s) fail (10) Unable to recalibrate fixed disk. Hard Disk(s) fail (08) Sector Verify failed. Keyboard is locked out - Unlock the key The BIOS detects that the keyboard is locked. Keyboard controller is pulled low. Keyboard error or no keyboard present Cannot initialize the keyboard. Make sure the keyboard is attached and no keys are being pressed during the boot.
Troubleshooting D Appendix D - Troubleshooting Troubleshooting Checklist This chapter of the manual is designed to help you with problems that you may encounter with your personal computer. To efficiently troubleshoot your system, treat each problem individually. This is to ensure an accurate diagnosis of the problem in case a problem has multiple causes. Some of the most common things to check when you encounter problems while using your system are listed below. 1.
D Troubleshooting The picture seems to be constantly moving. 1. The monitor has lost its vertical sync. Adjust the monitor’s vertical sync. 2. Move away any objects, such as another monitor or fan, that may be creating a magnetic field around the display. 3. Make sure your video card’s output frequencies are supported by this monitor. The screen seems to be constantly wavering. 1. If the monitor is close to another monitor, the adjacent monitor may need to be turned off.
Troubleshooting D Hard Drive Hard disk failure. 1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS. 2. If the system is configured with two hard drives, make sure the bootable (first) hard drive is configured as Master and the second hard drive is configured as Slave. The master hard drive must have an active/bootable partition. Excessively long formatting period.
D Troubleshooting System Board 172 1. Make sure the add-in card is seated securely in the expansion slot. If the add-in card is loose, power off the system, re-install the card and power up the system. 2. Check the jumper settings to ensure that the jumpers are properly set. 3. Verify that all memory modules are seated securely into the memory sockets. 4. Make sure the memory modules are in the correct locations. 5.
