P/N 8514-220-001PR MODEL T1450 90 LB CAPACITY COMPUTER CONTROL OPL WASHER DEXTER LAUNDRY, INC.
Please read this information and retain for reference. WARNING - THIS WASHER IS EQUIPPED WITH DEVICES AND FEATURES RELATING TO ITS SAFE OPERATION. TO AVOID INJURY OR ELECTRICAL SHOCK, DO NOT PERFORM ANY SERVICING UNLESS QUALIFIED TO DO SO. IT IS THE RESPONSIBILITY OF THE OWNER TO CHECK THIS EQUIPMENT ON A FREQUENT BASIS TO ASSURE ITS SAFE OPERATION. A machine should not be allowed to operate if any of the following occur: • • • • Excessively high water level.
INSTALLATION INSTRUCTIONS All washers must be installed in accordance with all local, state, and national building, electrical, plumbing and other codes in effect. WARNING - THESE INSTALLATION AND SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED PERSONNEL ONLY. TO AVOID INJURY AND ELECTRIC SHOCK, DO NOT PERFORM ANY SERVICING UNLESS QUALIFIED. FOUNDATION REQUIREMENTS This machine is designed for use on or over bare concrete floor - not to be used above combustible flooring.
T1450 INDUSTRIAL WASHER MOUNTING DIMENSIONS 2 15/16 41 1/2 X 7 1/4 42 1/4 17 7/8 16 1/8 3 3/16 9 1 Load laundry, close and latch door 2 Add detergent and fabric softener into dispenser on front of machine 3 Select desired wash CYCLE w ith 4 Press START POWER TERM. Detergent and button. 5 If bleach is requi red, add when ADD BLEACH l ight comes on. buttons.
ELECTRICAL ╔════════════════════════════════════════════════════════════════════╗ ║ WARNING ║ ║ SHUT OFF POWER AND WATER BEFORE OPENING ANY SERVICE PANELS. ║ ╚════════════════════════════════════════════════════════════════════╝ Dexter T1450 washing machines are intended to be permanently installed appliances. The machine should be connected to an individual branch circuit not shared by lighting or other equipment.
CHEMICAL INJECTION Dexter T1450 washing machines are intended to be permanently installed appliances. The machine is intended to have a chemical injection system operating with it. There are convenient electrical connection points for the injection pumps shown in Figure 3. Up to four (4) independent pumps can be controlled through the signals A, B, C and D. The injection pump signals are 24 VAC. The COM shown in Figure 3 is the common or return for these injection signals.
MODEL WCND90HCX-12SZ CAPACITY 90LBS/13.7 CUBIC FT. (40.8 kg/388 l) ELECTRICAL 208-240 VAC, 60 HERTZ, 1 OR 3 PHASE EXTRACTION FORCE 200 G’S WASH SPEED SPIN SPEED 39 R.P.M. 615 R.P.M.
OPERATING CONTROLS There are four (4) switches that control the washer operation. shown below, followed by an explanation of each switch. Each switch is Figure 7 - Push-button Control Switches STOP (RED) Push-button - Depress momentarily. Stops the washer during the cycle. All washer cycle information is retained, the door remains locked, and the water remains in the tub. STOP (RED) Push-button - Depress and hold for 3 seconds or longer. Stops the washer and clears the cycle.
OPERATING INSTRUCTIONS 1. Ensure that power is turned on to the washer. 2. Ensure that the ADVANCE/RUN/PROGRAM key lock is in the RUN position. 3. Load the clothes loosely in the cylinder, and latch the door securely. Be sure clothing does not get caught between the door gasket and tub front when closing the door. NOTE: To begin closing the door, the handle must be in the horizontal position.
END OF CYCLE At the end of the cycle, the machine stops, the END CYCLE LED lights, the alarm sounds, and the loading door unlocks allowing unloading of the machine. SAFETY DOOR LOCK This machine is equipped with a safety door lock, which prevents opening the door if power is interrupted, until it is safe to do so. If power failure occurs, it will be necessary to wait 2 to 3 minutes before the door can be opened. MOTOR DRIVE INDICATORS There are three small red L.E.D.s located on the upper drive cover.
FIGURE 9 - BATH SETTING LIMITS Settings for Setting Limits Description each bath Cycle Time 0 to 30 minutes (1 min. increments) The Cycle time (tumble) settings are 0 min. to 30 min. in 1 min. increments for each bath. If the setting is 0, then that bath is skipped over. For the Final Rinse /Extract bath, the minimum time must be 1 min. The water temperature setting is displayed as HH = hot, CH = warm, CC = cold and EE = No Water HOT, WARM, Temp. COLD and NO water bath.
required segments are edited. The previously stored parameters will appear as each part of the segment data is reviewed. 6. Push the green ENTER button. The Cycle Time LED lights, (lower row of LED's), and the segment LED is out. The tumble time for this segment will be shown on the display. If no change is required, then continue to the next instruction.
11. Push the green ENTER button. (The extract time has now been entered.) Once depressed, the Spin Time LED is out, and the editing of one segment is complete. The next sequential cycle segment LED lights, unless the segment edited above was the Final Rinse/Extract segment. If the Final Rinse/Extract segment is edited, after step eleven, the cycle programming is complete, and the machine will return to the Programming Mode awaiting a cycle select (Step 3).
To end the test, push STOP and the machine will return to the programming mode with cycle 31 displayed. The sequence of operation for the diagnostic cycle is explained below: • All indicators are lit and "00" is on the display. the washer is active. • Push the SCROLL UP button. For each number in the START button is pushed by pushing and holding move from one function No other function of The display will show 01. test, the function will be active momentarily when the and released.
• Step 12 - Intermediate spin. The I/O interface outputs labeled Reverse and Speed1 will be active (the two RED LED’s will light). • Step 13 - Full speed spin. The I/O interface outputs labeled Reverse, Speed1 and Speed2 will be active (the three RED LED’s will light). DO NOT USE STEP 14 IF YOU HAVE CUSTOMIZED CYCLES PROGRAMMED, AS THIS WILL SET THE CYCLES BACK TO THE FACTORY PRESETS. • Step 14 - Preset Cycles. Push START and hold, then push SCROLL UP.
Notes: The cycle cannot be advanced during the “open drain” step of the bathes. The cycle cannot be advanced when the hot and cold water valves to the tub are on after advancing during or after a chemical injection. The cycle cannot be advanced again while the hot and cold water valves to the tub are on after advancing when the water temperature was 65 to 90. The Rapid Advance mode may only be entered after a cycle is started.
OPL 90 POUND WASHER COMPUTER CONTROLLED PRESET CYCLE INFORMATION APPLICATION Shirt/Laundry CYCLE # 1 2 DESCRIPTION Shirts (No Starch) Shirts (Starch) Hotel/Motel 3 4 5 6 7 8 9 10 11 12 White Sheets White Pillowcases White Towels, Bath Mats, Wash Cloths Colored Sheets and Towels Delicate Wash Housekeeping Rags and Mops Housekeeping Uniforms Stain Treatment Reclaim Part 1 Part 2 Health Care 13 14 15 16 17 Sheets and Pillowcases Towels Diapers and Pads Personals Delicate Food & Beverage 18 19 20 21 2
CYCLE 1 Shirt/Laundry Shirts (No Starch) Segment Cycle Time Water Temp Water Level Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final 12 2 2 2 HH CH CH CH LO HI HI HI 4 CH LO Inject Source Spin Time Detergent/Bleach1 3 Total Time: 25 minutes excluding the tub fill time. Notes: 1. Use only oxygen bleach in shirt laundries. DO NOT USE CHLORINE BLEACH.
CYCLE 3 Hotel/Motel White Sheets Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time 7 7 2 2 Water Temp Water Level Inject Source HH HH CH CH LO LO HI HI Detergent Bleach 4 CH LO Sour/Soft Spin Time 1 4 Total Time: 27 minutes excluding the tub fill time.
CYCLE 5 Hotel/Motel White Towels Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 7 1 7 2 2 HH HH HH CH CH LO HI LO HI HI Detergent 4 CH LO Sour/Soft Bleach Spin Time 1 5 Total Time: 29 minutes excluding the tub fill time.
CYCLE 7 Hotel/Motel Delicate Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level 8 2 2 2 CH HH CH CH HI HI HI HI 4 CH LO Inject Source Spin Time Detergent/Bleach Sour/Soft 4 Total Time: 22 minutes excluding the tub fill time.
CYCLE 9 Hotel/Motel Uniforms Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 2 CH HI 7 7 2 2 HH HH CH CH LO LO HI HI Detergent Bleach 4 CH LO Sour/Soft Spin Time 1 4 Total Time: 29 minutes excluding the tub fill time.
CYCLE 11 Hotel/Motel Reclaim (Part 1) Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 20 3 HH HH LO HI Manual 3 HH HI Spin Time 1 Total Time: 27 minutes excluding the tub fill time.
CYCLE 13 Health Care Sheets and Pillowcases Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 3 2 7 7 2 2 CH CH HH HH CH CH HI HI LO LO HI HI Detergent Bleach 4 CH LO Sour/Soft Spin Time 1 4 Total Time: 32 minutes excluding the tub fill time.
CYCLE 15 Health Care Diapers Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time 3 2 2 7 2 7 2 2 4 Water Temp Water Level CH CH CH HH HH HH CH CH CH HI HI HI LO HI LO HI HI LO Inject Source Spin Time Detergent Bleach Sour/Soft 1 4 Total Time: 36 minutes excluding the tub fill time.
CYCLE 17 Health Care Delicate Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level 2 CH HI 7 2 2 2 CH CH CH CH HI HI HI HI 4 CH HI Inject Source Spin Time Detergent/Bleach Sour/Soft 3 Total Time: 22 minutes excluding the tub fill time.
CYCLE 19 Food and Beverage Colored Cotton Linen Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 2 CH HI 10 7 2 2 HH HH CH CH LO LO HI HI Detergent Bleach 4 CH LO Sour/Starch Spin Time 1 4 Total Time: 32 minutes excluding the tub fill time.
CYCLE 21 Food and Beverage Colored 100% Polyester Linen Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 2 CH HI 10 7 2 2 HH HH CH CH LO LO HI HI Detergent Bleach 4 CH LO Sour/Starch Spin Time 1 4 Total Time: 32 minutes excluding the tub fill time.
CYCLE 23 Food and Beverage Kitchen Rags Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 5 2 8 2 7 2 HH HH HH HH HH CH LO HI LO HI LO HI Detergent 2 CH HI Detergent Bleach Spin Time 1 1 5 Total Time: 35 minutes excluding the tub fill time.
CYCLE 25 Food and Beverage White/Colored 100% Polyester Linen Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 2 CH HI 10 1 2 2 2 HH HH HH CH CH LO HI LO HI HI Detergent/Bleach 4 CH LO Sour/Starch Spin Time 4 Total Time: 27 minutes excluding the tub fill time.
CYCLE 27 Food and Beverage Kitchen Rags Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 5 2 10 1 2 2 HH HH HH HH HH CH LO HI LO HI HI HI Detergent 2 CH HI Spin Time Detergent/Bleach 1 5 Total Time: 30 minutes excluding the tub fill time.
CYCLE 29 Other Oxygen Bleach Terry (No Iron) Segment Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level 3 2 10 2 2 2 CH CH HH HH CH CH HI HI LO HI HI HI 4 CH LO Inject Source Spin Time Detergent/Bleach 1 Sour/Soft 5 Total Time: 31 minutes excluding the tub fill time.
CYCLE Segment Cycle Time Water Temp Water Level Inject Source Spin Time Inject Source Spin Time Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Total Time: Notes: CYCLE Segment Cycle Time Water Temp Water Level Flush Pre-wash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Total Time: Notes: 34