User's Manual
Table Of Contents
- Important Safety Instruction
- Relevant Indications
- Panel Description
- Connections Quick Guide
- Quick Guide
- Before You Start to Play
- Connecting the AC Adaptor
- Connecting the Pedals
- Connecting External Audio Amplifier
- Listening Through Headphones
- Connecting Digital Player devices
- Connecting the VIVO S7/S3 to MIDI devices
- Connecting the VIVO S7/S3 to Your Computer
- Connecting an USB Memory (commercially available)
- Installing Music Rest
- Ground Terminal
- Turning the Power On/Off
- Demo of the VIVO S7/S3
- Basic Operation
- Selecting Tones
- Additional Sound - USER Sound
- Sound Effects
- Personalizing Your Sounds
- Other Functions
- Practice with Song Player
- Recording Your Performance
- Working with the Memories
- About the Memories and Memory Set structure.
- Saving Your Settings in the Internal Memory
- Recalling your Settings from Internal Memory
- Saving Your Settings in the USB Memory (commercially available)
- Recalling your settings from an USB Memory
- Renaming a Memory
- Exporting a Memory Set in the USB Memory
- Importing a Memory Set from the USB Memory.
- Playing with Audio Backing Tracks
- Wireless Function
- Master Equalizer
- Master Keyboard Functions
- MENU Options (Advanced Section)
- Appendix
- Troubleshooting
- Specifications
- Index
- Switch
- SETTING Parameters Group
- T2L EDITOR
- EFFECTS
- CONTROL
- TUNING
- MEMORY
- USB REMOVE
- AUDIO INPUT
- BLUETOOTH
- MIDI
- GLOBAL
- VERSION INFO
19
Installing Music Rest
Safely Remove the USB Memory
NOTE
You should always safely eject the USB Memory before
physically unplugging it from USB socket. Before to unplug the
USB Memory use the "USB REMOVE" function.
1. Press the "MENU" button.
2. Use the [] [] buttons to scroll the list and select the
"USB REMOVE" function.
3. Press the [] buttons to access the function.
The display shows:
1. Press the "YES" Function button to safely remove the USB
Memory.
Now you can unplug the USB Memory safely.
Installing Music Rest
Install the included music rest as shown in the illustration below.
Ground Terminal
Depending on the circumstances of a particular setup, you could
feel a tingling sensation at the point where touch this device.
You can eliminate this sensation connecting the ground terminal
with an external ground.
VIVO S7/S3 REAR SIDE
1. Use the screw-type ground terminal to connect to ground
or to connect to the chassis of the mixer, preamp, or other
device in your system.
Turning the Power On/O
Once everything is properly connected, be sure to follow the
procedure below to turn on their power.
1. Rotate the [VOLUME] the knob toward the left position to
minimize the volume.
NOTE
Before turning the VIVO S7/S3 on/o, always be sure to turn the
volume down. Even with the volume turned down, you might
hear some sound when switching the VIVO S7/S3 on/o.
However, this is normal and does not indicate a malfunction.
2. Press the VIVO S7/S3’s [ " ] button located on the right
panel to switch it on.
The power will turn on, a progress bar appear in the VIVO S7/S3’s
display,.
After a brief interval, the main page will appear. and VIVO S7/S3 will
be ready to produce sound.
3. Use the [VOLUME] knob to adjust the volume.
NOTE
This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will
operate normally.
Turning the Power O
1. Rotate the [VOLUME] the knob toward the left position to
minimize the volume.
NOTE
To avoid malfunctions, never disconnect the AC/DC adapter
while the instrument is turned on.
2. Press the VIVO S7/S3’s [ " ] switch.
A power o conrmation message appears: