Product Overview

5
ORDERING INFORMATION
www.elcoconstruction.com
©2021 ELCO – REV. A
ORDERING INFORMATION
Alumi-Flex Self-Drilling Structural Screws
Cat. No.
5
Description
(Diameter- TPI x
Nominal Length)
Point Type Finish
Maximum
Load-Bearing
Length
1
(in.)
Minimum
Protrusion
Length
2
Nominal Head
Diameter
3
(in.)
Nominal Head
Height
4
(in.)
Qty / Carton
#10 Diameter, 5/16" Hex Washer Head
EAH430-I #10-16 X 1/2" #3 Stalgard GB 0.063 7/16" 0.400 0.140 8,000
EAH445-I #10-16 X 3/4" #3 Stalgard GB 0.250 1/2" 0.400 0.140 6,000
EAH460-I #10-16 X 1" #3 Stalgard GB 0.500 1/2" 0.400 0.140 5,000
#10 Diameter, #2 Phillips Undercut Flat Head
EBM160-I #10 - 16 x 1" #3 Stalgard GB 0.500 1/2" 0.350 0.075 10,000
#12 Diameter, 5/16" Hex Washer Head
EAH630-I #12 - 14 x 3/4" #3 Stalgard GB 0.250 1/2" 0.415 0.180 5,000
EAH650-I #12 - 14 x 1" #3 Stalgard GB 0.500 1/2" 0.415 0.180 5,000
EAH680-I #12 - 14 x 1-1/2" #3 Stalgard GB 1.000 1/2" 0.415 0.180 3,000
1/4" Diameter, 3/8" Hex Washer Head
EAH800-I 1/4" - 14 x 3/4" #3 Stalgard GB 0.188 9/16" 0.500 0.220 3,500
EAH820-I 1/4" - 14 x 1" #3 Stalgard GB 0.438 9/16" 0.500 0.220 3,000
EAH870-I 1/4" - 20 x 1" #4 Stalgard GB 0.375 5/8" 0.500 0.220 2,000
EAH835-I 1/4" - 14 x 1-1/2" #3 Stalgard GB 0.938 9/16" 0.500 0.220 2,000
EAH880-I 1/4" - 20 x 1-1/2" #4 Stalgard GB 0.875 5/8" 0.500 0.220 2,000
1/4" Diameter, #3 Phillips Undercut Flat Head
EBM260-I 1/4" - 14 x 1" #3 Stalgard GB 0.438 9/16" 0.480 0.100 4.500
1. The Maximum Load Bearing Length is calculated by subtracting the Minimum Protrusion Length from the Nominal Length of the fastener.
2. Minimum Protrusion Length is the length that allows three full threads to protrude out of the back side of the supporting material.
3. Nominal head diameter is the diameter of the integral washer on hex washer head fasteners.
4. Nominal head height includes the thickness of the integral washer on hex washer head fasteners.
Load Bearing Area
Hex Washer Head Undercut Flat Head
Screwguns
Cat. No. Description Screw Diameter
DW268 2,500 RPM VSR VERSA-CLUTCH
™
Screwgun #10
DW267 2,000 RPM VSR VERSA-CLUTCH
™
Screwgun #12 & 1/4"
DCF622M2 20V MAX* XR
®
VERSA-CLUTCH™ Adjustable Torque Screwgun Kit #10-1/4"
*For 20V MAX* Maximum initial battery voltage measured without a workload is 20 volts. Nominal voltage is 18.
Fasteners must be installed perpendicular to the work surface using a maximum 2500 RPM screw gun with a torque sensing
nose piece.
Guidance on installation RPM of particular screw diameters can be found on page 1.
Impact tools are not recommended for the installation of Alumi-Flex fasteners.
Accessories
Cat. No. Description
DW2046 2" Bit Tip Holder
DWA1PH2IR2 #2 Phillips Bit Tip (2 Pack)
DWA1PH3IR2 #3 Phillips Bit Tip (2 Pack)
DW2219IR 5/16" Impact Ready
®
Nut Driver
DW2223IR 3/8" Impact Ready
®
Nut Driver
DWA2SLS30 Screwdriving Set
DWA2FTS25IR Screwdriving Set
ALUMI-FLEX
®