Product Overview

ManualsBrandsDewalt ManualsAir Conditioning Installation Parts#12 - 14 x 1-1/2" Alumi-Flex Hex Washer Head Screws (Box of 3000)

PERFORMANCE DATA

www.elcoconstruction.com

Ultimate Tension Pull-Out Capacity of Screw Connections in Aluminum, lbf

1,2

Diameter Point Type

Aluminum Thickness: 6061-T6

1/16" 3/32" 1/8" 3/16" 1/4" 5/16"

#10-16 #3 300 745 1,280 - - -

#12-14 #3 305 750 1,340 2,065 - -

1/4"-14 #3 340 835 1,450 2,805 2,825 -

1/4"-20 #4 - 1,055 1,615 2,880 2,880 2,885

1. Ultimate strengths are based on laboratory tests.

2. Ultimate load capacities must be reduced by a minimum safety factor to determine allowable loads (ASD) or by a load resistance factor to determine strength design capacities (LRFD).

Allowable Tension Pull-Out Capacity of Screw Connections in Aluminum, lbf

1,2,3,4,5

Diameter Point Type

Aluminum Thickness: 6061-T6

1/16" 3/32" 1/8" 3/16" 1/4" 5/16"

#10-16 #3 100 250 425 - - -

#12-14 #3 100 250 445 690 - -

1/4"-14 #3 115 280 485 935 940 -

1/4"-20 #4 - 350 540 960 960 960

1. Allowable (ASD) capacities are based on a safety factor,  = 3.00 in accordance with AC491.

2. Allowable (ASD) capacities are based on 6061-T6 aluminum members with a minimum tensile strength of F

= 42 ksi and a minimum yield strength of F

= 35 ksi.

3. Allowable (ASD) pull-out capacities for other member thicknesses may be determined by interpolating within the table.

4. For aluminum with a minimum tensile strength F

≥ 45 ksi and a minimum yield strength of F

= 40 ksi, multiply tabulated values by 1.14.

5. For ASD tension connections, the lower of the ASD tension strength, ASD pull-out strength and ASD pull-over strength must be used for design.

Design (LRFD) Tension Pull-Out Capacity of Screw Connections in Aluminum, lbf

1,2,3,4,5

Diameter Point Type

Aluminum Thickness: 6061-T6

1/16" 3/32" 1/8" 3/16" 1/4" 5/16"

#10-16 #3 150 370 640 - - -

#12-14 #3 150 375 670 1,035 - -

1/4"-14 #3 170 420 725 1,400 1,410 -

1/4"-20 #4 - 530 810 1,440 1,440 1,445

1. Design (LRFD) capacities are based on a resistance factor,

=0.50 in accordance with AC491.

2. Design (LRFD) capacities are based on 6061-T6 aluminum members with a minimum tensile strength of F

= 42 ksi and a minimum yield strength of F

= 35 ksi.

3. Design (LRFD) pull-out capacities for other member thicknesses may be determined by interpolating within the table.

4. For aluminum with a minimum tensile strength F

≥ 45 ksi and a minimum yield strength of F

= 40 ksi, multiply tabulated values by 1.14.

5. For LRFD tension connections, the lower of the LRFD tension strength, LRFD pull-out strength and LRFD pull-over strength must be used for design.

ALUMI-FLEX