www. .
Dansk (oversat fra original brugsvejledning) 4 Deutsch (übersetzt von den Originalanweisungen) 13 English (original instructions) 23 Español (traducido de las instrucciones originales) 31 Français (traduction de la notice d’instructions originale) 41 Italiano (tradotto dalle istruzioni originali) 51 Nederlands (vertaald vanuit de originele instructies) 61 Norsk (oversatt fra de originale instruksjonene) 71 Português (traduzido das instruções originais) 80 Suomi (käännetty alkuperäisestä kä
Figure 1 c d a b Figure 2 g j i h f e 1
Figure 3 k Figure 4 c l 2
Figure 5 a b Figure 6 3
E N GL I SH STRAIGHT GRINDER DW882 Congratulations! An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users.
EN G LIS H EC-Declaration of Conformity MACHINERY DIRECTIVE DW882 DEWALT declares that these products described under “technical data” are in compliance with: 2006/42/EC, EN 60745-1, EN 60745-2-3. These products also comply with Directive 2004/108/EC. For more information, please contact DEWALT at the following address or refer to the back of the manual. The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of DEWALT.
E N GL I SH d) e) f) g) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.
EN G LIS H After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time. h) Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses.
E N GL I SH Safety Warnings Specific for Grinding Operations a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe. b) The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator.
EN G LIS H Electrical Safety The electric motor has been designed for one voltage only. Always check that the power supply corresponds to the voltage on the rating plate. Machine is grounded (class I) in accordance with EN 60745, therefore earth connection is required. If the supply cord is damaged, it must be replaced by a specially prepared cord available through the DEWALT service organization. Mains Plug Replacement (U.K.
E N GL I SH WARNING: ALWAYS wear working gloves while operating this tool. WARNING: The gear case becomes very hot during use. WARNING: • Ensure all materials to be ground are secured in place. • Apply only a gentle pressure to the tool. Do not exert side pressure on the disc. • Avoid overloading. Should the tool become hot, let it run a few minutes under no load condition. Proper Hand Position (fig. 1, 7) WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown.
EN G LIS H Optional Accessories WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT, recommended accessories should be used with this product. Consult your dealer for further information on the appropriate accessories. Spare wheel part no.: 403216-00 Protecting the Environment Separate collection.
