www. .
Copyright DEWALT 2
Figure 1 q a d b dd q c e f s i g j DW771 cc y p k l ff o h m n Figure 2 r x w dd z bb aa y v v t ff u v 1
Figure 3 hh Figure 4 ii jj kk ll jj oo nn mm mm Figure 5 Figure 6 pp nn rr qq Figure 7 Figure 8 bb aa z Figure 9 b ss gg h e f g 2 Figure 10 q
Figure 11 Figure 12 e vv uu tt n Figure 13 Figure 14 n yy i p m o ww l Figure 16 Figure 15 h a3 ee t xx 3
Figure 17 h xx Figure 19 Figure 18 a4 a3 a2 t zz u a1 ee Figure 20 4 a2
Figure 21 Figure 22 Figure 23 Figure 24 5
EN GL I S H DW771, DW777 CROSS-CUT MITRE SAW Congratulations! You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users. Technical data Voltage (U.K. & Ireland only) Power input Blade diameter Blade bore Max. blade speed Mitre (max. positions) Bevel (max.
ENGLI SH Safety instructions WARNING! When using electric tools basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury including the following. Read all these instructions before attempting to operate this product and save these instructions. SAVE THIS MANUAL FOR FUTURE REFERENCE General Safety Rules 1. Keep work area clear. Cluttered areas and benches invite injuries. 2. Consider work area environment. Do not expose the tool to rain.
EN GL I S H • Consider applying specially designed noise-reduction blades. • Do not use HSS blades. • Do not use cracked or damaged saw blades. • Do not use any abrasive discs. • Never use your saw without the kerf plate. • Check for damage to the tool, parts or accessories which may have occurred during transport. • Take the time to thoroughly read and understand this manual prior to operation. Description (fig. 1, 2, 9) WARNING: Never modify the power tool or any part of it.
ENGLI SH pp. Roller table • The plug fitted should be comply with BS EN 60309 (BS4343), 16 Amps, earthing contact position 4h. qq. Dust extraction tubes WARNING: Always ensure that the cable clamp is correctly and securely fitted to the sheath of the cable. rr. Three-way connector Electrical safety The electric motor has been designed for one voltage only. Always check that the power supply corresponds to the voltage on the rating plate.
EN GL I S H where the mounting screw holes are located. Clamping at any other point will interfere with the proper operation of the saw. 3. To prevent binding and inaccuracy, be sure the mounting surface is not warped or otherwise uneven. If the saw rocks on the surface, place a thin piece of material under one saw foot until the saw is firm on the mounting surface. Mounting the saw blade (fig.
ENGLI SH Instructions for use WARNING: Always observe the safety instructions and applicable regulations. The attention of UK users is drawn to the “woodworking machines regulations 1974” and any subsequent amendments. Prior to operation WARNING: • Install the appropriate saw blade. Do not use excessively worn blades.The maximum rotation speed of the tool must not exceed that of thesaw blade. • Do not attempt to cut excessively small pieces. • Allow the blade to cut freely. Do not force.
EN GL I S H WARNING: If the cutting angle varies from cut to cut, check that the bevel clamp handle and the mitre clamping knob are securely tightened. These must be tightened after making any changes in bevel or mitre. • The chart shown below will assist you in selecting the proper bevel and mitre settings for common compound mitre cuts. • To use the chart, select the desired angle “A” (fig. 24) of your project and locate that angle on the appropriate arc in the chart.
ENGLI SH WARNING: To reduce the risk of injury, regularly clean the dust collection system. Optional accessories WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT, recommended accessories should be used with this product. The roller table (pp) makes the handling of large and long pieces of wood very easy (fig. 5).
Belgique et Luxembourg België en Luxemburg Black & Decker - DEWALT Nieuwlandlaan 7, IZ Aarschot B156 B-3200 Aarschot Tel: +32 (0)015 - 15 47 9211 Fax: +32 (0)015 - 15 47 9210 www.dewalt.be Danmark DEWALT Sluseholmen 2-4 2450 København SV Tlf: 70201511 Fax: 70224910 www.dewalt.dk Deutschland DEWALT Richard-Klinger-Straße 65510 Idstein Tel: 06126-21-1 Fax: 06126-21-2770 www.dewalt.de Ελλάς Black & Decker (Hellas) S.A.
