Use and Care Manual
4.
Press
the
forward
or
back arrow
to
select
OFF or ON.
TIME STAMP TIME STAMP
OFF
ON
OFF
ON
5. Press
the OK
button
to
save changes.
6. Press
the
main menu button
to
exit.
To Format Micro
SD
Card
NOTICE:
Formatting
the
micro
SD
card will erase
ail data.
1.
Press
the
main menu button
to
show
the
Main Menu.
2.
Press
the
forward
or
back arrow
to
select
the
Format Disk option.
FORMAT DISK
Caution:
Formatting will erase all data
NO
YES
FORMAT DISK
Are you sure you want to format disk?
NO
YES
5. Press
the OK
button
to
save changes
and
exit.
To Change Default Setup
NOTICE:
Changing
to
default setup will erase current settings
and restore factory
settings.
1.
Press
the
main menu button
to
show
the
Main Menu.
2.
Press
the
forward
or
back arrow
to
select
the
Default Setup
option.
03
Date/Time
Language
I U Format Disk
'3
Default Setup
01
Time Stamp
•
Folder
tn
DEWALT
Copyright
3. Press
the OK
button
to
navigate
to the
next screen.
4.
Press
the
forward
or
back arrow
to
select
NO or YES.
03
Date/Tlme
•P Language
U
Formal Disk
Default Setup
0
Time Stamp
•
Folder
CD
DEWALT
Copyright
r
3. Press
the OK
button
to
navigate
to the
next screen.
16
4.
Press
the
forward
or
back arrow
to
select
NO or YES.
DEFAULT SETUP
Caution:
Will restore factory settings
NO
YES
DEFAULT SETUP
Caution:
Will restore factory settings
NO
YES
5. Press
the OK
button
to
save changes
and
exit.
Operating Tips
•
Use
only
DEWALT
12V
Max* lithium
ion
battery.
• Ensure
the
DEWALT
battery
is In
good working condition.
If the low
battery Indicator light
on the
screen
is
flashing,
the
battery needs
to
be
recharged.
•
To
extend battery life, make sure
to
turn both
the
screen
and the
handle
set off
when
not in use.
• Make sure
the
screen
is
fully charged before operation.
MAINTENANCE
Cleaning
AwARNING: Blow dirt
and
dust
off
with
clean,
dry air at
least once
a
week. To
minimize
the
risk
of eye injury,
always wear ANSI
287.1
approved
eye
protection when performing
this.
AWARNING: Never
use
solvents
or
other harsh chemicals
for
cleaning
the
non-metallic parts
of the tool.
These chemicals
may
weaken
the
plastic materials used
In
these
parts. Use a
cloth
dampened only with water
and
mild
soap.
Never
let any
liquid
get
inside
the tool;
never Immerse
any
part
of the
tool Into
a liquid.
CHARGER GLEANING INSTRUCTIONS
AWARNING: Shock
hazard.
Disconnect
the
charger from
the AC
outlet before
cleaning.
Dirt
and
grease
may be
removed from
the
exterior
of the
charger using
a
cloth
or
soft non-metallic
brush.
Do
not
use
water
or any
cleaning solutions.
n-oubleshooting
• Make sure
the 12V
Max* battery
Is
charged.
• Make sure
the
screen
is
fully charged.
• Make sure
the
screen
is
always attached
to the
handle
set. The
picture
may
freeze
If you
attempt
to
remove
the
(screen) from
the
handle
set
while taking
a
photo
or
video.
• Make sure
the
battery
Is
installed
on the
handle
set
when
in use.
• Make sure
the
camera cable
is
attached
to the
handle
set
properly.
• Make sure
the
handle
set is
turned
on as
well
as the
screen.
• Make sure
the
back
of the
handle
set is not
covered with debris
so
the screen slides
on
easily
and no
damage
to the
screen occurs.
•
If the
screen freezes
or
won't turn
on.
Insert
a
small object
(i.e.,
paper clip
end)
Into
the
reset button located
on the
back
of the
screen.
•
If the
picture
Is dim,
roll
the
brightness control switch
to
brighten
the
LED
light.
Accessories
AWARNING: Since accessories, other than those offered
by
DFWALT,
have
not
been tested with this
product, use of
such
accessories with this tool could
be
hazardous.
To
reduce
the
risk
of
Injury,
only DFWALT recommended accessories should
be
used with
this
product.
17