User Manual

12
ENGLISH
Proper hand position requires one hand on the auxiliary
handle
7
with the other hand on the main handle
14
.
Variable Speed Trigger Switch (Fig.A)
The variable speed trigger switch permits speed control from 0
to 2200RPM.
To turn the tool on, squeeze the trigger switch
5
. The farther
you depress the trigger, the faster it will operate. Releasing the
trigger turns the tooloff.
Use lower speeds for applying compounds, and higher speeds
forpolishing.
Trigger Locking Button
The tool can be locked on for continuous use by squeezing
the trigger switch
5
fully and depressing the lock button
11
shown in FigureA. Hold the lock button in as you gently release
the triggerswitch.
To turn the tool off from a locked-on position, squeeze and
release the trigger switchonce.
Proper Hand Position (Fig. E)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicableregulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.
NOTE: The trigger switch can only be locked on with the tool
running at the maximum RPM designated by the speed control
wheel
3
.
Speed Control Wheel (Fig.A)
The maximum speed of your tool can be changed by rotating
the speed control wheel
3
to the desired setting. For added
versatility, the trigger switch
5
may be locked in its full on
position and tool speed changed by means of the speed control
wheelalone.
The speed control wheel can be set for any speed between
800and 2200 RPM and the variable speed trigger switch will
then control tool speed from zero to the wheel setting. For
example: A control wheel setting of 2200 RPM will allow the
variable speed trigger switch to operate the tool between
zero and 2200 RPM, depending on how far the trigger switch
isdepressed.
Electronic Speed Control
The electronic speed control feature functions whenever the
trigger switch is fully depressed and the tool is running at the
selected speed determined by the setting of the controlwheel.
As you load the tool by pushing it down on the work surface,
the tool will compensate for the loading and maintain the
selected speed. If the speed selected by the control wheel is
2200 RPM, the tool will maintain 2200 RPM, as it isloaded.
• The electronic speed control operates only when the trigger
switch
5
is fullydepressed.
• The effect of electronic speed control is much easier to
observe at lower speed settings (1400 RPM and below), than
at highspeeds.
A conventional polisher running at a typical no-load speed of
2200 RPM slows down to about 1800 RPM under a polishing
load. Your polisher will continue to run at 2200 RPM (or any
speed you select with the control wheel) as a load is applied.
If the speed is too great, slow the tool down with either the
trigger switch or the controlwheel.
Polishing (Fig.E)
1. Without turning the tool on, grasp the handles of the tool
and pick itup.
2. Keep the tool away from your body and depress the
triggerswitch.
3. Make sure you have a firm grip on thehandles.
4. Move the tool evenly over the surface of the workpiece,
without applyingpressure.
5. Switch off the machine before taking the tool from
thesurface.
6. Check your work at shortintervals.
The auxiliary handle
7
can be easily changed to either side of
the tool for left-handed or right-handedoperation.
Use utmost care when power polishing around or over sharp
objects and contours. It is very important to use the correct
pressure while polishing various sections of an automobile
body. For example, light pressure should be applied when
To Attach Polishing Pad With Hook And Loop
Backing Pad (Fig. A, D)
1. Insert the centring tube
19
into the centre hole in the hook
and loop backing pad
21
.
2. Line up the centre hole on the hook and loop pad
20
with
the centring tube
19
and attach the pad to the hook and
loop backing pad
21
.
3. Screw backing pad
21
onto spindle
8
, while depressing
spindle lock button
6
.
To Remove Pads
Turn the pads by hand in the opposite direction from normal
rotation to allow lock button to engage spindle, then unscrew
pads in normal direction for right-handthread.
Prior to Operation
1. Be sure the polishing pad is mountedcorrectly.
2. Make sure the pad rotates in the direction of the arrows on
the accessory and thetool.
3. Make sure any dirt is washed off the workpiecesurface.