Operating Guide

ENGLISH
10
Be sure to tighten chuck with one hand on the chuck sleeve
and one hand holding the tool for maximumtightness.
To release the accessory, repeat steps 1 and 2above.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can causeinjury. Exception—Tool
Connect™ functions and mode adjustments require
battery to beinstalled.
Mode Selector (Fig. A, J)

WARNING: To reduce the risk of injury, remove
accessories from the tool chuck before using the
modeselector.
Your tool is equipped with a mode selector that allows 3
modes to be customized using the Tool Connect™ app.
Home settings are active when the home indicator
13
is
lit. The following 3 features can becustomized. For more
information, refer to Table 1below.
Once configured, pressing the mode selector button
12
on
the foot of the tool will cycle through the modes
14
.
If you are unsure of the current configuration, press the
mode selector button
12
to set the tool to the Home
setting (home indicator
13
is lit).
12
Fig. J
13 14
DeWALT
Tool Connect™

WARNING: To reduce the risk of injury, remove
accessories from the tool chuck before any Tool
Connect™interaction.
NOTICE: Always check the tool configuration prior
to use. If you are unsure of the current configuration,
press the mode selector button
12
(Fig. J) to set the
tool to the Home setting as described on the label and
thismanual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://
www.bluetooth.com/Pages/Bluetooth-Smart-Devices-List.
aspx)
DeWALT
Tool Connect™ is an application for your smart
device (such as a smart phone or tablet) that connects the
device to your tool to allow you to configure specific tool
functions. Refer to ModeSelector.
NOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use
of such marks by
DeWALT
is under license. Other trademarks
and trade names are those of their respectiveowners.
NOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobileapplication.
Download the
DeWALT
Tool Connect™ applicationat:
• Follow the instructions in the app to create your Tool
Connect™account.
• On the Home screen of the app, select "+ Tool" to begin
the process of adding your tool to the app.
• To connect your tool with the
DeWALT
Tool Connect™
app, at the appropriate screen, press the mode selector
button
12
for 3–5 seconds, then wait for the tool to
connect. The tool can only be connected to one Tool
Connect™ account at a time.
• Once the tool has been connected, you can confirm that
you would like to register the product.
For more information on
De
WALT Tool Connect™
functionality and features, please call 1–800–4-
DeWALT
(1–800–433–9258), visit www.dewalt.com or view
the FAQ page and help screens located inside the
mobileapplication.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your
local
DeWALT
service center. Do not attempt to replace the
coin cell batteryyourself.

WARNING: Danger of explosion if battery is
incorrectlyreplaced.

WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/
button cell battery. If the coin/button cell battery is
Table 1
Customizable Features Home
Factory Presets
Customizable RangeMode 1 Mode 2 Mode 3
Worklight brightness MED OFF MED HIGH OFF–HIGH
Worklight delay off 20 secs 20 secs 20 secs 20 minutes 0–20 minutes
Maximum speed (RPM) Speed 1
Speed 2
550
2000
550
2000
550
2000
550
2000
180–550
600–2000