www. .
Figure 1 d c f e b a i k g h h j Figure 2 j k l 1
m Figure 3 n Figure 4 Figure 5 Figure 6 c c Figure 8 Figure 7 f 2 Figure 9
ENGLISH CORDLESS COMPACT 13 mm (1/2") DRILL/DRIVER DCD730, DCD780 CORDLESS COMPACT 13 mm (1/2") DRILL/DRIVER/ HAMMERDRILL DCD735, DCD785 Congratulations! You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users. Technical Data Voltage Type Battery Type Power output No-load speed 1st gear 2nd gear Impact rate 1st gear 2nd gear Max.
EN GLI S H Vibration emission value ah Screwdriving ah,ID = Uncertainty K = m/s² m/s² < 2.5 1.5 2.5 1.5 The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. VDC Ah kg Charger Mains voltage Battery type Approx. charging time min Weight kg Fuses Europe U.K. & Ireland DCB140 Li-Ion 14.4 3.0 0.
ENGLISH EC-Declaration of Conformity MACHINERY DIRECTIVE DCD730, DCD735, DCD780, DCD785 DEWALT declares that these products described under Technical Data are in compliance with: 2006/42/EC, EN 60745-1, EN 60745-2-1, EN 60745-2-2. These products also comply with Directive 2004/108/EC and 2011/65/EU. For more information, please contact DEWALT at the following address or refer to the back of the manual.
EN GLI S H d) e) f) g) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.
ENGLISH • Wear safety goggles or other eye protection. Hammering and drilling operations cause chips to fly. Flying particles can cause permanent eye damage. • Accessories and tool may get hot during operation. Wear gloves when handling them if performing heat producing applications such as hammerdrilling and drilling metals. • Do not operate this tool for long periods of time. Vibration caused by hammer action may be harmful to your hands and arms.
EN GLI S H • Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock or electrocution. • When operating a charger outdoors, always provide a dry location and use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. 2. Insert the battery pack (j) into the charger, making sure the pack is fully seated in the charger.
ENGLISH Important Safety Instructions for All Battery Packs When ordering replacement battery packs, be sure to include the catalog number and voltage. The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below and then follow the charging procedures outlined. READ ALL INSTRUCTIONS • Do not charge or use the battery pack in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
EN GLI S H 3 Li-Ion battery packs (M3, L3, C3 models) Read instruction manual before use. 1 Li-Ion battery pack (M1, L1, C1 models) 1 Kitbox 1 Instruction manual Charging. Fully charged. x 1 Exploded drawing NOTE: Battery packs, chargers and kitboxes are not included with N-models. Hot/cold pack delay. • Check for damage to the tool, parts or accessories which may have occurred during transport. Problem pack or charger.
ENGLISH Electrical Safety The electric motor has been designed for one voltage only. Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains. Your DEWALT charger is double insulated in accordance with EN 60335; therefore no earth wire is required. If the supply cord is damaged, it must be replaced by a specially prepared cord available through the DEWALT service organisation.
EN GLI S H NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on start up. This is normal and does not indicate a problem. Torque Adjustment Collar (fig. 1) Your tool has an adjustable torque screwdriver mechanism for driving and removing a wide array of fastener shapes and sizes and in some models, a hammer mechanism for drilling into masonry. Circling the collar (c) are numbers, a drill bit symbol, and in some models, a hammer symbol.
ENGLISH To move belt hook or bit clip, remove the screw (h) that holds it in place then reassemble on the opposite side. Be sure to securely tighten the screw. OPERATION Instructions for Use WARNING: Always observe the safety instructions and applicable regulations. WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. Proper Hand Position (fig.
EN GLI S H NOTE: A smooth, even flow of dust from the hole indicates proper drilling rate. Screwdriver Operation (fig. 6) 1. Select the desired speed/torque range using the dual range gear selector to match the speed and torque of the planned operation. 2. Turn the torque adjustment collar (c) to the desired position. Lower numbers indicate lower torque settings; higher numbers indicate higher torque settings. 3. Insert the desired fastener accessory into the chuck as you would any drill bit. 4.
ENGLISH advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. You can check the location of your nearest authorised repair agent by contacting your local DEWALT office at the address indicated in this manual. Alternatively, a list of authorised DEWALT repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com.
Belgique et Luxembourg België en Luxemburg Black & Decker - DEWALT Nieuwlandlaan 7, IZ Aarschot B156 B-3200 Aarschot Danmark DEWALT Sluseholmen 2-4 2450 København SV Tlf: 70201511 Fax: 70224910 www.dewalt.dk Deutschland DEWALT Richard Klinger Str. 11 65510 Idstein Tel: 06126-21-1 Fax: 06126-21-2770 www.dewalt.de Ελλάς Black & Decker (Ελλάς) Α.Ε. Στράβωνος 7 & Βουλιαγμένης 159 Γλυφάδα 16674, Αθήνα España DEWALT Parque de Negocios “Mas Blau” Edificio Muntadas, c/Bergadá, 1, Of.
