Technical data

ManualsBrandsDeVillbiss Air Power Company ManualsAir Compressor38301-9615

INSTRUCTIONS–P

ARTS LIST

308–185

Rev. F

Supercedes

Rev

. E

110/230V, 15/7.5A, ONE CYLINDER, COMPACT OIL–LESS

Compressor

GRACO Part No. 236–526, Series A

DeVILBISS Part No. CAC–4093

EQUIPMENT MISUSE HAZARD

Equipment

misuse can cause the equipment to rupture or malfunction and result in serious injury



This equipment is for professional use only



Read all instruction manuals, tags, and labels before operating the equipment.



Use the equipment only for its intended purpose. If you are not sure, call Graco T

echnical Assis

tance at 1–800–543–0339.



Do not expose the system to rain. Always store the system indoors.



Do not alter or modify this equipment.



Check equipment daily

. Repair or replace worn or damaged parts immediately



Do not exceed the maximum working pressure of the lowest rated component in your system.

This equipment has a

100 psi (7 bar) maximum working pressure at 100 psi (7 bar) maxi

mum incoming air pressure.



The system is for use only with water-based simulated acoustic and wall texture materi

als.

Use fluids and solvents compatible with the equipment wetted parts. Refer to the

Technical

Data

section of all equipment manuals. Read the fluid and solvent manufacturer

’

s warnings.



Never directly inhale compressed air

. Compressed air may contain toxic vapors.

 W

ear appropriate clothing, eye protection, and breathing apparatus for the material sprayed.

 T

o reduce the risk of serious injury

, including electric shock and splashing fluid in the eyes, follow

the

Pressure Relief Procedure

on page 2 before checking or repairing the compressor

FIRE AND EXPLOSION HAZARD

Improper

grounding, poor ventilation, open flames or sparks can cause a hazardous condition and

result in a fire or explosion and serious injury



Locate the sprayer at least 20 ft (6.1 m) away from any explosive vapors, due to arcing parts.



Use a time delay fuse or circuit breaker protected electrical circuit of the specified voltage and

amperage. In the U.S. and Canada, the fuse must be marked with a T



Comply with all applicable local, state, and national fire, electrical, and safety regulations.

WARNING

INSTRUCTIONS

GRACO INC. P.O. BOX 1441

MINNEAPOLIS, MN

55440–1441

COPYRIGHT

1991, GRACO INC.

This manual contains important

warnings and information.

READ AND RETAIN FOR REFERENCE

Summary of content (4 pages)

PAGE 1
INSTRUCTIONS–PARTS LIST 308–185 Rev. F This manual contains important warnings and information. READ AND RETAIN FOR REFERENCE Supercedes Rev. E 110/230V, 15/7.5A, ONE CYLINDER, COMPACT OIL–LESS Compressor GRACO Part No. 236–526, Series A DeVILBISS Part No. CAC–4093 WARNING WARNING EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury. INSTRUCTIONS This equipment is for professional use only.
PAGE 2
General Information Air intake filter replacement WARNING To reduce the risk of serious injury, including electric shock and splashing fluid in the eyes, follow the Pressure Relief Procedure before checking or repairing the compressor. Pressure Relief Procedure 1. Shut off the sprayer. Remove and wash both air intake filters every time you flush the system. A dirty filter will not allow the compressor to operate at full capacity. Replace the filters if they are worn.
PAGE 3
Rebuilding the Compressor 2 4 B 3 10 22 A C 7 8 9 Torque to 30–45 in-lb (3.4–5 N.m) Torque to 75–90 in-lb (8.5–10 N.m) For Series B compressor: Use button head capscrew and torque to 75–90 in-lb (8.5–10 N.m) For Series A compressor: use hex screw and torque to 30–35 in-lb (3.4–3.9 N.m) 12,13 14 16 Using cross pattern, torque to 84–120 in-lb (9.5–13.5 N.m) 1. Remove the fan (14). 2. Disassemble the compressor head (3) as shown.
PAGE 4
Parts 1* 2 4 5 6 3 22* 10* 20 7 19 8 11 9 Torque to 30–45 in-lb (3.4–5 N.m) 14 For Series B compressor: Use button head capscrew and torque to 75–9 0 in-lb (8.5–10 N.m) 18 17 For Series A compressor: use hex screw and torque to 30–35 in-lb (3.4–3.9 N.m) 12,13 Using cross pattern, torque to 84–120 in–lb (9.5–13.5 N.m) Manual Change Summary 21 Ref DeVILBISS No. Part No. GRACO Part No.