Specifications

Important: Before using this equipment,
read all safety precautions and instruc-
tions. Keep for future use.
Halogenated Hydrocarbon Sol-
vents - for example: 1, 1, 1 -
trichloroethane and methylene
chloride can react with the alu-
minum in this cup and cause an
explosion hazard. Read the data
sheet for the material you intend
to spray. Do not use spray mate-
rials containing these solvents
with this cup.
DESCRIPTION
Two models are available:
120175 ( GFC-502 )1 Liter Cup
802199 ( GFC-504 ) 20 oz. Cup
This cup is designed to be used with or
without the DeVilbiss disposable cup liner.
The cup liner allows painting in any
position and simplifies clean up.
The cup is constructed from durable
aluminum to provide trouble-free opera-
tion. The cup insert is electroless nickel
plated brass. The disposable cup lid is
recyclable and is constructed with
recycled polyethylene. The lid has a unique
drip check to prevent paint from dripping
out of the vent in the lid.
ASSEMBLY OF CUP TO GUN
1. Remove one of the cup gaskets
(#4 (White) for GFG and GFHV guns)
(#4A (Blue) for GTI, FLG, M1-G and
Compact guns) from the poly bag.
2. Place this cup gasket in the fluid inlet
of the gun body. See Cup Drawing.
3. Store remaining cup gasket in a safe
place for future use.
4. Place filter (3) in cup outlet at this time
if desired. See Cup Drawing.
5. Assemble cup to gun and tighten hand
tight.
FILLING WITH PAINT
Fill the cup with paint to the full mark.
Do not overfill.
INSTALLING THE LID
Place plastic lid on the top of the cup, and
push in the center of the lid to assemble
lid. Fold vent cap and push onto center
portion of lid (if vent cap is not already
assembled).
CLEANING
Note
For routine cleaning, it is not nec-
essary to remove cup from gun.
Do not remove washer (4) from
gun. If washer (4) is removed, it
must be replaced.
Do not soak the lid in solvent for
extended periods of time. Doing
so could cause cup/lid sealing
problems and leakage.
SERVICE BULLETIN
SB-4-043-K
Replaces SB-4-043-J
120175 (GFC-502) & 802199 (GFC-504)
Aluminum Gravity Feed Cups
3
4
1 (1 Liter)
1A (20 oz.)
2
Full Mark
4A
For GFG & GFHV
guns (White)
For GTI, FLG,
M1-G, PRI &
GFG PLUS
guns (Blue)
Cup Drawings
Cup Fitting
Gun Body
Cup Gasket
(4) (4A)
Filter (3)
Drain Hole
The cup lid is designed to be disposable
but may be cleaned and reused if slightly
contaminated with overspray. If lid be-
comes tight, or does not fit, it is due to
extended soaking in solvent. Let lid air
dry overnight and the lid should return to
its original size and fit.
Remove lid and properly dispose of any
excess paint. Pour in a small amount of
clean solvent. The amount will vary with
different coatings and solvents. Reinstall
lid. Shake cup to wash down the inside
surfaces. Hold lid while shaking to
prevent lid from coming off. Pull trigger
to allow some solvent to be flushed
through gun. Remove lid and pour out
dirty solvent. Add a small amount of
clean solvent and repeat procedure.
Wipe exterior of lid with a clean cloth
and clean solvent.
If a paint filter was used in the bottom of
the cup outlet, it should be removed and
cleaned or replaced at this time. Dispose
of used cup lid if contaminated and
replace with new.
Ref. Replacement
No. Part No. Description
1 GFC-502 Metal Gravity Feed Cup (1Liter)
1A GFC-504 Metal Gravity Feed Cup (20 oz.)
2 GFC-404-K2 Disposable Lid Kit (Kit of 2)
3 KGP-5-K5 Filter Kit (Kit of 5)
4 KGP-12-K5 Cup Gasket (White) (Kit of 5)
4A KGP-13-K5 Cup Gasket (Blue) (Kit of 5)
PARTS LIST