Specifications

ManualsBrandsDeVilbiss ManualsPaint SprayerHVLP Gravity Feed Spraygun

4 • GRAVITY FEED SPRAY GUNS

ACCESSORIES

The Ultimate HVLP

Base Coat/Clearcoat Gun

• Excellent value

• Three guns in one

GTi

Millennium Gravity Feed

Order No. Fluid Inlet Air

Model No. Tip (mm) Pressure Applications

170156 1.3 & 1.4 20-25 PSI Base coats

GTI-620G 25-30 PSI High solids clearcoats,

(Includes single stages

1.3 mm,

1.4 mm, and 1.5 20-25 PSI Base coats

1.5 mm 25-30 PSI Low solids clearcoats,

ﬂuid tips) single stages

GTi

Millennium Gravity Feed HVLP Air Cap

#2000 air cap Base coats, clearcoats, primers, single

stage, and low VOC

Air cap pattern 4-10 PSI (air cap) 12.5-16.0 CFM

@ 30 PSI inlet

Gravity Tips: 1.2 mm, 1.3 mm, 1.4 mm,

1.5 mm, 1.6 mm, 1.8 mm,

2.0 mm, 2.2mm

Air Cap Order No. 192136

Air Cap Model No. GTI-407-2000

Included tip sizes shown in bold

For complete

parts breakdown

please see

page 38

GTi

Millennium

HVLP

GRAVITY

FEED

Gun Order No.

170156

Model No.

GTI-620G

130095

HAF-507-K2

Whirlwind ﬁlter

192246

BXX-1250

Single gun case

GTi

Gravity Gun

Includes:

• 1.3 mm, 1.4 mm, and

1.5 mm ﬂuid tips

• 1-Liter aluminum cup

with push on lid

• High output air adjusting

valve with gauge

• Spray lube, ﬂuid ﬁlter,

gun hook

220052

HA-5867

⁄8˝ HVLP air hose

assy. (35´)

12˝

802187

DGI-501-PSI

Digital pressure gauge

120175

GFC-502

1-Liter aluminum

gravity cup

Summary of content (10 pages)

PAGE 1
GTi® Millennium The Ultimate HVLP Base Coat/Clearcoat Gun Hvlp Gravity Feed • Excellent value Gun Order No. • Three guns in one 170156 Model No. GTI-620G GTi® Millennium Gravity Feed HVLP Air Cap #2000 air cap Base coats, clearcoats, primers, single stage, and low VOC Air cap pattern 4-10 PSI (air cap) Gravity Tips: 12˝ GTi® Gravity Gun Includes: • 1.3 mm, 1.4 mm, and 1.
PAGE 2
Customer Service 1-800-445-3988 Refer to Service Bulletin: SB-2-168 16 GTi Millennium HVLP Gravity Feed Spray Gun ® 15 17 14 13 10 18 12 170156 (GTI-620G) HVLP Gravity Feed 32 33 34 35 11 36 7 6 192140 (KK-5060) Air Cap Cleaning Kit 38 Consists of: 5 4 5 4 Fan Air Port 3 Center Air Port 1 2 brushes & 1 wirepick. Helps keep air cap clean and performing properly. 2 8 (See DETAIL #8) Fluid Tip (Torque to 15-20 ft.lbs.
PAGE 3
SERVICE BULLETIN SB-2-168-K Replaces SB-2-168-J Repair Kit KK-5058-2 GTI HIGH VOLUME LOW PRESSURE GRAVITY FEED SPRAY GUN #2000 Millennium Air Cap PSI / CFM Information INLET PRESSURE at handle of gun (PSI) CAP PRESSURE fan fully open (PSI) CFM FLOW (CFM) 8 14.5 20 24.5 30 2 4 6 8 10 7.5 10.5 12.5 14.5 15.5 INSTALLATION OPERATION For maximum transfer efficiency, do not use more pressure than is necessary to atomize the material being applied.
PAGE 4
Page 2 SB-2-168-K SAFETY PRECAUTIONS This manual contains information that is important for you to know and understand. This information relates to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the following symbols. Please pay particular attention to these sections. NOTE Important safety information - A hazard that may cause serious injury or loss of life.
PAGE 5
SB-2-168-K To clean fluid passages, remove excess material from cup, then flush with a suitable solvent. Wipe gun exterior with a solvent dampened cloth. Never completely immerse in solvent as this is detrimental to the lubricants and packings. Chart 1 PARTS REPLACEMENT Figure 1 Air Cap Fluid Tip No. Air Cap No. No. 2000 NOTE When replacing the fluid tip or fluid needle, replace both at the same time. Using worn parts can cause fluid leakage. See Chart 1. Also, replace the needle packing at this time.
PAGE 6
Page 4 SB-2-168-K 18 17 16 14 15 13 12 10 11 32 33 34 35 36 6 7 5 4 *26 Air Inlet Nipple 1/4" NPS(M) (Torque to 15 ft.lbs.) 2 1 9 3 Fluid Tip (Torque to 15-20 ft.lbs.) 19 Use medium strength thread sealant (i.e. Devcon #2242 Blue, or equal) on threads 8 29 28 12 21 24 23 22 31 27 20 30 25 PARTS LIST Ref. No. Replacement Part No.
PAGE 7
SB-2-168-K TROUBLESHOOTING CONDITION Heavy top or bottom pattern CAUSE CORRECTION Horn holes plugged. Obstruction on top or bottom of fluid tip. Cap and/or tip seat dirty. Clean. Ream with non-metallic point. Clean. Page 5 Clean. Heavy right or left side pattern Left or right side horn holes plugged. Dirt on left or right side of fluid tip. Clean. Ream with non-metallic point. Clean. Remedies for the top-heavy, bottom-heavy, right-heavy, and left-heavy patterns: 1.
PAGE 8
Page 6 SB-2-168-K TROUBLESHOOTING (continued) CONDITION CAUSE CORRECTION Fluid dripping or leaking from bottom of cup Cup loose on gun. Cup gasket worn or missing below cup. Cup threads dirty. Tighten. Replace cup gasket. Clean. Runs and sags Too much material flow. Material too thin. Gun tilted on an angle, or gun motion too slow. Adjust gun or reduce fluid flow. Mix properly or apply light coats. Hold gun at right angle to work and adapt to proper gun technique.
PAGE 9
SERVICE BULLETIN SB-4-043-K Replaces SB-4-043-J 120175 (GFC-502) & 802199 (GFC-504) Aluminum Gravity Feed Cups Important: Before using this equipment, read all safety precautions and instructions. Keep for future use. FILLING WITH PAINT Fill the cup with paint to the full mark. Do not overfill. INSTALLING THE LID Halogenated Hydrocarbon Solvents - for example: 1, 1, 1 trichloroethane and methylene chloride can react with the aluminum in this cup and cause an explosion hazard.
PAGE 10
Page 2 SB-4-043-K ACCESSORIES OMX-70-K48 PAINT CUP LINER KIT (Not for use with GFC-503 cups) Allows quick and easy clean-up. Consists of : 1 - Piercing Tool 48 - Disposable Liners 48 - Drain Bushings WARRANTY This product is covered by DeVilbiss' 1 Year Limited Warranty. DeVilbiss Worldwide Sales and Service Listing: www.devilbiss.com ITW Industrial Finishing ITW Automotive Refinishing DeVilbiss has authorized distributors throughout the world.