Pressure OPERATOR'S Washers MANUAL SAFETY "ASSEMBLY "OPERATION "MAINTENANCE TROUBLESHOOTING "QUICK FACTS Register your product www.devap.com "STORAGE" on line at Read Operator's Manual. Do not operate equipment until you have read this Operator's Manual for Safety, Assembly, _, and Maintenance instructions. D22322 Rev.
SAFETY GUIDELINES - DEFINITIONS ........... IMPORTANT SAFETY INSTRUCTIONS ........ 2 Quick Connect 3-4 .................... 11 How to Siphon Chemicals/Cleaning Solvents..12 FREQUENTLY ASKED QUESTIONS ............ 5 Starting ............................. 12 OWNER'S RESPONSIBILITIES ................ 6 Shutting Down Your Pressure Washer ....... 13 PRESSURE WASHER SERVICE POLICY ......... 6 BOX CONTENTS .......................... 7 Engine .............................. 13 ASSEMBLY ........
iMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT iN SERIOUS iNJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING. HAZARD WHAT CAN HAPPEN o RiSK OF EXPLOSION Spilled gasoline and it's vapors can become ignited from cigarette sparks, electrical arcing, exhaust gases, and hot engine components such as the muffler. HOW TO PREVENT iT o Shut off engine and allow it to cool before adding fuel to the tank.
HAZARD WHAT CAN HAPPEN • Spray directed at electrical outlets or switches, or objects connected to an electrical circuit, could result in a fatal electrical shock. RiSK OF ELECTRICAL SHOCK RiSK TO FLUID iNJECTiON RiSK OF CHEMICAL BURN RiSK OF HOT SURFACES RiSK OF iNJURY AND PROPERTY DAMAGE WHEN TRANSPORTING OR STORING HOW TO PREVENT iT Unplug any electrically operated product before attempting to clean it. Direct spray away from electric outlets and switches.
What kind of oil do i use? • Engine: Refer to Engine manual for oil recommendations. Pump: See page 12 and 13. My Pressure Washer won't start..(See Engine manual for starting instructions) Has gasoline been added to the engine? Is engine on/off switch in "on" position? (If applicable) Has engine been primed or choked? Adequate amount of oil in engine? (Some models are equipped with a "Low Oil Shut Down" switch) Is fuel valve in the "Open" position.
DO NOT RETURN THIS PRODUCT TO THE RETAILER! Call 1=800=888=2468, Ext. 2. o Read and understand all safety warnings. o Read this Owner's Manual. o Do not operate this unit until you have read this Owners Manual for Safety, Operation, and Maintenance Instructions. • Read the Engine Owner's Manual supplied with this unit. • Check for visible shipping damage. Shipping damage will cause problems in operation of this unit.
Handle Quick Connect Nozzle - only on units equipped with the quick connect lance Bagged Engine Frame and Wheel Assembly High Pressure Hose Handle English/ Spanish Operator's Manual Knobs w/hardware k____ 0 Chemical Nozzle Cleaning Bagged Hose Engine Oil Kit Parts .
1. Connect handle to frame. TO ASSEMBLE ACCESSORIES PANEL (if equipped) OR 1. Remove top screws on handle assembly. 2. Loosen bottom screws on handle assembly. 3. Place grooves in accessories panel assembly onto screws and slide panel assembly into place. 4. Place screws (removed earlier) into the top holes and secure accessories panel assembly to handles. Do not overtighten. i 2. Connect wand to gun. Tighten securely. Attach high pressure hose to gun.
BASIC ELEMENTS WASHER OF A PRESSURE Bypass Mode: In Bypass Mode, the pump is recirculating water because the trigger of the spray gun is not pulled. High Pressure Pump: Increases the pressure of the water supply. Engine: Drives the high pressure pump. Chemical Injection: Feeds cleaning agents into the pump to mix with the pressurized water and help in cleaning. Water Supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 PSI and 5 gallons per minute.
Thermal Relief VaJve HOW TO USE WAND In an effort to prevent damage, pumps are equipped with a thermal relief valve. This valve will open when the temperature inside the pump rises too high. This valve will then release a gush of water in an effort to lower the temperature inside the pump. Immediately after this occurs, the valve will close. See the Box Contents to determine if your unit is equipped with a multi-reg or quick connect wand.
For Quick-Connect Wands: Chemical nozzle - Black. This nozzle is used to apply chemicals or cleaning solutions. powerful stream. Spray Nozzles Your pressure washer is equipped with up to five spray nozzles. Each nozzle is color coded and delivers a specific spray pattern for a particular cleaning purpose. The size of the nozzle determines the size of the fan spray and the pressure out of the nozzle. The 0°, 15° , 25 °, and 40 ° nozzles are high pressure nozzles.
STARTING 1. Never turn water supply off while pressure washer engine is running or damage to pump will result. Add fresh high quality unleaded gasoline. Never fill fuel tank indoors. 9. Never fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank. SOME UNITS ARE NOT EQUIPPED WiTH AN EZ START VALVE. ON THESE UNITS PRES= SURE WiLL BUILD iN THE HOSE iF THE ENGINE DOES NOT START AFTER TWO PULLS.
SHUTTING 1. 2. DOWN If you have siphoned chemicals, siphon a bucket of clean water through the chemical hose. NOTE: Failure to do so will cause damage to the pump. 3. Turn water source off. 4. Pull trigger on spray gun to relieve any water pressure in hose or spray gun. 5. See Storage section in this manual for proper storage procedures. Turn engine off. See Engine Owner's Manual. NOTE: NEVER turn the water off with the engine running.
PUMP MAINTENANCE PUMP TYPE CHART OiL TYPE OiL CAPACITY CHANGE First t0 hours Annovi OiL after every 50 hours Reverberi (XMV) 30W non detergent 13.5 oz. x x Annovi Reverberi (XRV) 30W non detergent t8.54 oz. x x Annovi Reverberi (XTV) 30W non detergent 9.92 oz, x x Annovi Reverberi (RKV) 30W non detergent t8.54 oz.
DAPC Axial HOW TO CLEAN THE WATER iNLET FILTER Cam Oil Fill Plug This screen filter should be checked periodically and cleaned if necessary. 1. Remove filter by grasping end and removing it from water inlet of pump as shown. 2. Clean filter by flushing it with water on both sides. 3. Install filter into water inlet of pump Oil Drain Annovi Reverberi Oil Fill Plug HOW TO CHANGE PUMP OIL 1. Loosen oil fill cap. 2. Place a container under the oil drain plug. 3. Remove oil drain plug. 4.
It is recommended that you follow these steps to protect the internal seals of the pressure washer when storing the unit for an extended period and WHEN FREEZING TEMPERATURES ARE EXPECTED. 5. Add RV antifreeze to hose as shown. 6. Pull engine starter rope slowly several times until antifreeze comes out of high pressure hose connection of pump. 7. Remove short hose from water inlet of pump. 8. Install spark plug into spark plug hole and tighten securely, then reconnect spark plug wire. 9.
PROBLEM CAUSE CORRECTION Engine will not start (see Engine Manual for further engine trouble- 1. 2. No fuel. Low oil (if equipped with low oil shutdown), 1. Add Fuel. 2. Add required amount of oil. shooting) 3. Pressure builds up after two pulls on the recoil starter or after initial 3. Squeeze gun trigger to relieve pressure. 4. 5. Push primer bulb 3 times or choke engine. Attach spark plug wire. use. No or low pressure (initial use) Will not draw chemicals 4. Not primed or choked. 5.
PROBLEM CAUSE CORRECTION No or low pressure (after period of normal use.) 1. 2. Worn seal or packing. Worn or obstructed valves. 1. 2. Have replaced byAWSC. 3. Worn unloader piston. 3. Have replaced by AWSC. 4. Worn E-Z start valve. 4. Have replaced by AWSC. 1. Worn or broken o-ring. 1. Check and replace. 2. Loose hose connection. 2. Tighten. 1. Loose connections. 1. Tighten. 2. Piston packings worn. 2. Have replaced by AWSC. 3. Worn or broken o-rings. 3.
DeVilbiss Air Power Company warrants to the original purchaser that each new pressure washer, service part, and accessory is free from defects in material and workmanship, and agrees to repair or replace under this warranty any defective product or part as follows from the original date of purchase. 1 Year - Consumer applications (i.e. personal residential household usage only). 90 Day - Commercial applications (income producing). Engine warranties are the responsibility of the engine manufacturer.
CALL 1=800=888=2468 EXT. 2 TO FiND A LOCAL AUTHORIZED SERVICE CENTER NEAR YOU FOR REPAIRS AND SERVICE PART PURCHASES. GAS OIL Use fresh high quality gas. Add stabilizer to fuel tank and run engine for 5 minutes before storage. Pump oil: Refer to owners manual supplied with this unit. Engine oil: Refer to engine manual supplied with this unit. Some units are equipped with a low oil sensor and adequate oil must be added or the unit will not start. Some units do not require oil.
