Workshop Manual
Table Of Contents
- Workshop Manual
- Table of contents
- 1 Foreword
- 2 General
- 3 User notes
- 4 Technical data
- 5 Job card overview
- 6 Job cards
- Removing and installing the crankcase bleeding
- Renewing the crankshaft sealing ring (opposite side to flywheel)
- Assembling/disassembling shaft sleeve on the crankshaft (opposite side to flywheel)
- Removing and installing the front cover (opposite side to flywheel)
- Checking the overhang of the cylinder liner
- Removing and installing the pressure holding valve
- Removing and installing the piston cooling nozzles
- Checking collar contact for cylinder liner
- Removing and installing the lubricating oil pan (metal sheet lubricating oil pan)
- Removing and installing the cylinder liner
- Testing the cylinder liner
- Removing and installing the V-belt, V-belt pulley
- Removing and installing torsional vibration damper (V-belt drive)
- Removing and installing the flywheel
- Removing and installing the crankshaft
- Checking the crankshaft
- Checking the axial clearance of the crankshaft
- Removing and installing the piston and con rod
- Checking the con rod
- Checking the piston
- Checking the piston rings and piston ring grooves
- Checking the compression pressure
- Removing and installing the cylinder head cover
- Removing and installing the exhaust return module
- Removing and installing the solenoid valve (exhaust gas return)
- Removing and installing cylinder head
- Checking piston overhang
- Removing and installing the valves
- Checking the valves
- Checking the valve guide
- Checking the valve lag
- Renewing the crankshaft sealing ring (flywheel side)
- Removing and installing the gearcase cover
- Removing and installing the camshaft
- Checking the camshaft
- Setting valve clearance (with or without removal of exhaust return module)
- Setting valve clearance (with exhaust return module installed)
- Removing and installing the rocker arm and rocker arm bracket
- Disassembling, assembling and checking the rocker arm and rocker arm bracket
- Removing and installing the lubricating oil cooler
- Removing and installing the lubricating oil cooler housing
- Removing and installing the oil suction pipe
- Removing and installing the control block
- Removing and installing the high-pressure pump (Installation position A)
- Removing and installing the high-pressure pump (Installation position B)
- Removing and installing the injector
- Removing and installing the fuel filter console
- Removing and installing the fuel supply pump (V-belt drive)
- Removing and installing the rail
- Removing and installing the pressure limiting valve
- Removing and installing the rail pressure sensor
- Removing and install the charge air line
- Removing and installing the coolant pump (V-belt drive)
- Removing and installing the thermostat
- Checking the thermostat (in the removed state)
- Removing and installing the thermostat housing
- Removing and installing the belt tensioner (V-rib belt)
- Removing and installing the fan drive
- Dismantling and assembling the fan drive
- Removing and installing the fan console (V-rib belt drive)
- Removing and installing the exhaust line
- Removing and installing the turbocharger
- Removing and installing the generator (V-belt drive)
- Removing and installing the starter
- Mounting engine on assembly block and demounting
- Removing and installing the engine mounting (elastic mounting)
- Removing and installing the cable harness
- Removing and installing the impulse transmitter (crankshaft)
- Removing and installing the impulse transmitter (camshaft)
- Removing and installing the pressure/temperature sensor (charge air)
- Removing and installing the oil pressure switch
- Removing and installing temperature transmitter (coolant)
- Removing and installing the fuel pressure sensor
- Installing and removing turning gear
- Installing and removing turning gear (Torsional vibration damper)
- Removing and installing the connection housing
- Check alignment of connection housing
- Removing and install the heating flange
- Removing and installing the glow plugs
- 7 Standard tools
- 8 Special tools
- Table of contents
5
© 02/2010 OBJ_DOKU-21742-001.fm
4/12
Job card overview
TCD 2013 2VSorted alphabetically
Removing and installing the coolant pump (V-belt
drive)
W 37-03-01 Coolant pump
Removing and installing the crankcase bleeding
W 01-01-01 Crankcase
Removing and installing the crankshaft
W 05-05-01 Crankshaft
Removing and installing the cylinder head cover
W 08-01-01 Cylinder head
Removing and installing the cylinder liner
W 04-01-01 Cylinder liner
Removing and installing the engine mounting
(elastic mounting)
W 47-01-01 Engine mounting
Removing and installing the exhaust line
W 41-01-01 Exhaust pipe
Removing and installing the exhaust return module
W 08-02-01 Cylinder head
Removing and installing the fan console (V-rib belt
drive)
W 39-04-03 Fan console
Removing and installing the fan drive
W 39-02-01 Fan drive
Removing and installing the flywheel
W 05-03-01 Flywheel
Removing and installing the front cover (opposite
side to flywheel)
W 01-03-01 Front cover
Removing and installing the fuel filter console
W 20-01-01 Fuel filter
Removing and installing the fuel pressure sensor
W 48-06-01 Electrical equipment
Removing and installing the fuel supply pump (V-
belt drive)
W 20-02-01 Fuel pump
Removing and installing the gearcase cover
W 09-02-02 Gearcase
Removing and installing the generator (V-belt drive)
W 44-02-01 Generator
Removing and installing the glow plugs
W 63-02-01 Start aid
Removing and installing the high-pressure pump
(Installation position A)
W 17-01-04 High-pressure pump
Removing and installing the high-pressure pump
(Installation position B)
W 17-01-05 High-pressure pump
Removing and installing the impulse transmitter
(camshaft)
W 48-02-03 Electrical equipment
Removing and installing the impulse transmitter
(crankshaft)
W 48-02-01 Electrical equipment
Removing and installing the injector
W 19-01-01 Injector
Removing and installing the lubricating oil c
ooler
W 1
5-02-01
Lubricating oil cooler
Removing and installing the lubricating oil cooler
housing
W 15-02-02 Lubricating oil cooler
Removing and installing the lubricating oil pan
(metal sheet lubricating oil pan)
W 02-01-01 Lubricating oil sump
Removing and installing the oil pressure switch
W 48-04-01 Electrical equipment
Removing and installing the oil suction pipe W 16-01-01 Oil suction pipe
Removing and installing the piston and con rod W 06-01-01 Connecting rod
Activity Job card Maintenance group