Workshop Manual
Table Of Contents
- Frontpage
- Table of contents
- Checking the compression pressure
- Mounting engine on assembly block and demounting
- Setting valve clearance
- Removing and installing the rocker arm and rocker arm bracket
- Disassembling, assembling and checking the rocker arm and rocker arm bracket
- Removing and installing cylinder head
- Checking piston overhang
- Removing and installing the crankcase bleeding
- Removing and installing the exhaust line
- Removing and install the charge air line
- Removing and installing the turbocharger
- Removing and installing the intake manifold
- Removing and installing the exhaust gas return valve
- Removing and installing the exhaust gas return pipe
- Removing and installing the exhaust gas collection pipe (Exhaust gas recirculation)
- Removing and installing the lifting magnet (Start amount release)
- Renewing the injection lines
- Removing and installing the fuel injectors
- Removing and installing the lifting magnet (charge air pressure-dependent full load stop)
- Installing and removing charge air pressure-dependent full load stop
- Removing and installing fuel pipes
- Removing and installing the fuel filter console
- Removing and installing the fuel supply pump
- Removing and installing the lubricating oil cooler
- Removing and installing the oil filter console
- Removing and installing the oil pressure switch
- Removing and installing the thermostat (Lubricating oil cooler)
- Removing and installing the control line
- Removing and installing the coolant pump
- Checking the thermostat (in the removed state)
- Removing and installing the thermostat
- Removing and installing the thermostat housing
- Removing and installing temperature transmitter
- Removing and installing the lifting magnet (Engine shutdown)
- Removing and installing the V-belt pulley
- Renew V-belts, check V-belt tension
- Removing and installing the flywheel
- Removing and installing the hydraulic pump
- Removing and installing the generator
- Removing and installing the starter
- Removing and installing the heating plugs
- Removing and installing the glow plug
- 7 Standard tools
- 8 Special tools
3
© 06/2008 17764-001
7/8
DEUTZ engines User notes
3.4.2 Structure of a job card
1. DEUTZ AG,
publisher of service documentation
2. Engine type (e.g. TCD 2013 4V)
3. Maintenance group
4. Job card number or topic
5. Title of job card
6. Reference to other job cards
7. Chapter
8. Graphic or photo
9. DEUTZ internal creation number
10.Page number
11.Date of issue of job card
12.Note
13.Danger / Important
14.Work sequence
15.Special tools; auxiliary materials
16.Conventional tools
3.5 Explanation of symbols
Triebwerk
W 02-04-01
6
16
12
4
6
1 2 3
8
10
11
5
7
5
9
13
14
15
8
Danger!
of death or to health. Must be observed!
For example: The incorrect use or conver-
sion of the turbocharger can lead to serious
injury.
Caution!
Danger to the component/engine. Non-
compliance can lead to destruction of the
component/engine.
Must be observed!
Note
General notes on assembly, environmental
protection etc. No potential danger for man
or machine.
Tool
Conventional and special tools required for
the work.
Auxiliary materials
Working materials required in addition to
the tools for performing the work
(e.g. greases, oils, adhesives, sealants)
References
to important documents or job cards for the
work process.
For example: Job card W 04-05-05
Reference
to a document or a job card within the work
process.
Test and setting data
The necessary values are specified here.
If several values are necessary, a cross re-
ference is given to the Test and Setting Va-
lues table.
For example:
ID no. P01 61 = valve clearance, inlet
Tightening specification
The necessary values are specified here.
If several values are necessary, a cross re-
ference is given to the Tightening Specifi-
cations table.
For example:
ID no. A01 001 = cylinder head screws