Workshop Manual
Table Of Contents
- Workshop Manual
- Foreword
- General
- User notes
- Technical data (Test and adjustment data)
- Technical data (Tightening specification)
- Job card overview (Sorted alphabetically)
- Job card overview (Sorted numerically)
- Job card overview (Job card references)
- W 00-02-06 Check compression
- W 00-05-01 Mount engine on assembly stand and disassemble
- W 01-01-01 Check and set valve clearance
- W 01-02-02 Remove and install toggle lever and toggle lever block
- W 01-02-06 Disassemble and complete, check toggle lever and toggle lever block
- W 01-04-04 Remove and install cylinder head
- W 03-01-11 Remove and install crankcase bleeding
- W 06-01-05 Remove and install exhaust manifold
- W 06-06-04 Remove and install turbocharger
- W 06-07-03 Remove and install air intake pipe
- W 07-02-07 Remove and install lifting magnet for start volume release
- W 07-03-01 Renew injection lines
- W 07-07-01 Remove and install injection valves (in engines with leak fuel line)
- W 07-08-01 Remove and install solenoid valve (LDA)
- W 07-08-02 Remove and install charge pressure full load stop (LDA)
- W 07-10-06 Remove and install fuel lines (with Motorpal injection pumps)
- W 07-10-06 Remove and install fuel lines (with Bosch injection pumps)
- W 07-10-08 Remove and install fuel filter console
- W 07-11-01 Remove and install fuel pump
- W 08-08-02 Remove and install oil cooler
- W 08-10-06 Remove and install oil filter cartridge
- W 08-11-07 Remove and install oil filter console
- W 08-11-08 Remove and install oil pressure switch
- W 08-11-09 Remove and install oil pressure sensor
- W 08-11-11 Remove and install oil temperature sensor
- W 08-11-12 Remove and install oil thermostat (oil cooler)
- W 08-15-01 Remove and install oil pressure line (turbocharger)
- W 08-15-02 Remove and install oil return line (turbocharger)
- W 08-16-01 Remove and install oil line for injection adjuster supply
- W 09-11-01 Remove and install cooling blower
- W 11-00-03 Remove and install lifting magnet (shutoff magnet)
- W 12-02-01 Check, renew V-belt (in FM, BFM engines)
- W 12-02-01 Check V-belt, renew (in FL and BFL engines)
- W 12-02-06 Remove and install V-belt clamping roller
- W 12-06-01 Remove and install flywheel
- W 12-08-02 Remove and install hydraulic pump
- W 13-01-02 Remove and install cable harness
- W 13-02-03 Remove and install generator (in FL and BFL engines)
- W 13-02-03 Remove and install generator (in FM and BFM engines)
- W 13-03-02 Remove and install starter
- W 13-06-01 Remove and install helical heater plug
- Commercial tools
- Special tools
Engine general
W 00-02-06
0312 1553 - 0138
3/4
© 11/2004
6
2011
z The measured compression pressure depends on
the starting speed during the measuring process and
the altitude of the engine installation site.
Limit values can therefore not be determined exactly.
The compression measurement is only
recommended as a reference measurement of all
cylinders of an engine to each other. If more than
15% deviation has been determined, the cause
should be determined by disassembling the cylinder
unit concerned.
No.
Kompression in bar
Compression value in bar
Pression en bar
Dat. _________
Best. Nr. 5 1341 250 00
DBGM Made in Germany
M
OTO
M
ETER
7250 Leonberg
10
15 20 25 30 35 40
1
2
3
4
5
6
7
8
Zyl.
© 33771 1
z Remove the compression tester and adapter.
© 39102 0
z Unscrew screw (1).
z Remove connection piece with sealing ring.
In FL, BFL engines
z Remove oil cooler
Î Job card W 08-08-02.
z Install injection valves
Î Job card W 07-07-01.
© 39103 0
1