Workshop Manual
Table Of Contents
- Workshop Manual
- Foreword
- General
- User notes
- Technical data (Test and adjustment data)
- Technical data (Tightening specification)
- Job card overview (Sorted alphabetically)
- Job card overview (Sorted numerically)
- Job card overview (Job card references)
- W 00-02-06 Check compression
- W 00-05-01 Mount engine on assembly stand and disassemble
- W 01-01-01 Check and set valve clearance
- W 01-02-02 Remove and install toggle lever and toggle lever block
- W 01-02-06 Disassemble and complete, check toggle lever and toggle lever block
- W 01-04-04 Remove and install cylinder head
- W 03-01-11 Remove and install crankcase bleeding
- W 06-01-05 Remove and install exhaust manifold
- W 06-06-04 Remove and install turbocharger
- W 06-07-03 Remove and install air intake pipe
- W 07-02-07 Remove and install lifting magnet for start volume release
- W 07-03-01 Renew injection lines
- W 07-07-01 Remove and install injection valves (in engines with leak fuel line)
- W 07-08-01 Remove and install solenoid valve (LDA)
- W 07-08-02 Remove and install charge pressure full load stop (LDA)
- W 07-10-06 Remove and install fuel lines (with Motorpal injection pumps)
- W 07-10-06 Remove and install fuel lines (with Bosch injection pumps)
- W 07-10-08 Remove and install fuel filter console
- W 07-11-01 Remove and install fuel pump
- W 08-08-02 Remove and install oil cooler
- W 08-10-06 Remove and install oil filter cartridge
- W 08-11-07 Remove and install oil filter console
- W 08-11-08 Remove and install oil pressure switch
- W 08-11-09 Remove and install oil pressure sensor
- W 08-11-11 Remove and install oil temperature sensor
- W 08-11-12 Remove and install oil thermostat (oil cooler)
- W 08-15-01 Remove and install oil pressure line (turbocharger)
- W 08-15-02 Remove and install oil return line (turbocharger)
- W 08-16-01 Remove and install oil line for injection adjuster supply
- W 09-11-01 Remove and install cooling blower
- W 11-00-03 Remove and install lifting magnet (shutoff magnet)
- W 12-02-01 Check, renew V-belt (in FM, BFM engines)
- W 12-02-01 Check V-belt, renew (in FL and BFL engines)
- W 12-02-06 Remove and install V-belt clamping roller
- W 12-06-01 Remove and install flywheel
- W 12-08-02 Remove and install hydraulic pump
- W 13-01-02 Remove and install cable harness
- W 13-02-03 Remove and install generator (in FL and BFL engines)
- W 13-02-03 Remove and install generator (in FM and BFM engines)
- W 13-03-02 Remove and install starter
- W 13-06-01 Remove and install helical heater plug
- Commercial tools
- Special tools
0312 1648 - 0138
3/8
© 11/2004
3
3 User notes
2011
!
3.1 General
The maintenance work prescribed in the operating manual and in the workshop manual must be performed on
schedule and completely.
The maintenance personnel must possess the necessary technical knowledge to perform the work. Safety and
protection devices which are removed during maintenance work must be replaced again afterwards.
Caution!
The rules for the prevention of accidents and the safety regulations must be observed during
maintenance work.
Also observe the special safety regulations for the different maintenance groups which are listed in detail as
job cards in the Job cards chapter (cf. also section 1.2).
See the maintenance schedules for the maintenance intervals. These also inform you of the work to be
performed.
The job cards provide technical instructions for performing the work.
3.2 Specifications
3.2.1 Safety regulations and rules for the prevention of accidents
For various maintenance groups, detailed safety notes in the form of job cards have been compiled, these
precede the job cards of the respective maintenance groups.
The legally prescribed rules for the prevention of accidents (available from professional associations or from
dealers) must be observed. These are dependent on the installation site, operating mode and the operating
and auxiliary materials being used.
Special protection measures depending on the respective work are specified and identified in the job
description.
It generally applies among other things:
z for the personnel
- Only instructed personnel may operate or maintain the engine. Unauthorized persons may not enter the
engine room.
- Wear close fitting clothing and ear protectors in the engine room when the engine is running.
- Only appoint qualified personnel to do repairs and maintenance.
z for the engine room:
- Ensure adequate ventilation (do not cover air shafts)
- Install first aid kit and suitable fire extinguishers. Check the filling and readiness for operation regularly.
- Only store inflammable materials in the engine room if these are necessary for operating the system.
- Smoking and naked lights are prohibited in the engine room.
z For operation and maintenance of the engine:
- Only start the engine when all protection devices are installed. Make sure that no-one is standing in the
danger area.
- Only perform cleaning, maintenance and repair work when the engine has been shut down and secured
against starting.
!