Workshop Manual
Table Of Contents
- Workshop Manual
- Foreword
- General
- User notes
- Technical data (Test and adjustment data)
- Technical data (Tightening specification)
- Job card overview (Sorted alphabetically)
- Job card overview (Sorted numerically)
- Job card overview (Job card references)
- W 00-02-06 Check compression
- W 00-05-01 Mount engine on assembly stand and disassemble
- W 01-01-01 Check and set valve clearance
- W 01-02-02 Remove and install toggle lever and toggle lever block
- W 01-02-06 Disassemble and complete, check toggle lever and toggle lever block
- W 01-04-04 Remove and install cylinder head
- W 03-01-11 Remove and install crankcase bleeding
- W 06-01-05 Remove and install exhaust manifold
- W 06-06-04 Remove and install turbocharger
- W 06-07-03 Remove and install air intake pipe
- W 07-02-07 Remove and install lifting magnet for start volume release
- W 07-03-01 Renew injection lines
- W 07-07-01 Remove and install injection valves (in engines with leak fuel line)
- W 07-08-01 Remove and install solenoid valve (LDA)
- W 07-08-02 Remove and install charge pressure full load stop (LDA)
- W 07-10-06 Remove and install fuel lines (with Motorpal injection pumps)
- W 07-10-06 Remove and install fuel lines (with Bosch injection pumps)
- W 07-10-08 Remove and install fuel filter console
- W 07-11-01 Remove and install fuel pump
- W 08-08-02 Remove and install oil cooler
- W 08-10-06 Remove and install oil filter cartridge
- W 08-11-07 Remove and install oil filter console
- W 08-11-08 Remove and install oil pressure switch
- W 08-11-09 Remove and install oil pressure sensor
- W 08-11-11 Remove and install oil temperature sensor
- W 08-11-12 Remove and install oil thermostat (oil cooler)
- W 08-15-01 Remove and install oil pressure line (turbocharger)
- W 08-15-02 Remove and install oil return line (turbocharger)
- W 08-16-01 Remove and install oil line for injection adjuster supply
- W 09-11-01 Remove and install cooling blower
- W 11-00-03 Remove and install lifting magnet (shutoff magnet)
- W 12-02-01 Check, renew V-belt (in FM, BFM engines)
- W 12-02-01 Check V-belt, renew (in FL and BFL engines)
- W 12-02-06 Remove and install V-belt clamping roller
- W 12-06-01 Remove and install flywheel
- W 12-08-02 Remove and install hydraulic pump
- W 13-01-02 Remove and install cable harness
- W 13-02-03 Remove and install generator (in FL and BFL engines)
- W 13-02-03 Remove and install generator (in FM and BFM engines)
- W 13-03-02 Remove and install starter
- W 13-06-01 Remove and install helical heater plug
- Commercial tools
- Special tools
0312 1649 - 0138
3/4
© 11/2004
2
2 General
2011
DEUTZ engines
are the product of years of research and development. The profound know-how gained in connection with high
quality requirements is the guarantee for manufacturing of engines with a long life, high reliability and low fuel
consumption. Naturally the high requirements for protection of the environment are also met.
Maintenance and care
are decisive for whether the engine satisfactorily meets the set demands. Compliance with the prescribed
maintenance times and the careful execution of maintenance and care are therefore essential. Difficult
operating conditions deviation from normal operation must be observed especially.
DEUTZ AG
Please consult one of our service representatives responsible for operating faults and spare parts questions.
Our trained specialist personnel ensures fast, professional repairs using original parts in the event of damage.
Original parts of the DEUTZ AG are always produced according to the latest state of the art.
Information about our service can be found at the end of this documentation.
Take care when the engine is running
Only perform maintenance work or repairs when the engine is at a standstill. Replace any removed protective
devices upon completion of the work. When working on the running engine, work clothing must be close fitting.
Safety
This symbol accompanies all safety notes. Observe these carefully.
Also pass on the safety instructions to your operating personnel. The ”General safety regulations and
rules for the prevention of accidents” of the legislator must be observed additionally.
Note
This symbol accompanies information of a general kind.
Observe these carefully.
Asbestos
Gaskets used in this engine are asbestos-free. Please use the appropriate spare parts for
maintenance and repair work.
!