Instruction manual Instruction manual Congratulations We congratulate you on your new caravan and would like to thank you for choosing a quality product from Dethleffs. Whether you want to enjoy your holidays on good or bad roads, whether you want to have your "holiday home" out in the country, at the seaside or in the mountains: Your Dethleffs caravan will always make sure that you can enjoy your holidays, because the Dethleffs team has been manufacturing caravans for 80 years and knows what is important.
Instruction manual Vehicle data Model: Chassis manufacturer: Serial number: Initial registration: Purchased from company: Expiry of the guarantee period: Key number: Chassis number: Family Card with long-term warranty Yes / No Customer address Surname, Christian name: Street, no.: Postal code, town: Dealer's stamp and signature We reserve the right to alter the construction, equipment and the scope of delivery. Special equipment is also listed that is not included in the standard scope of delivery.
Contents 1 Guarantee. . . . . . . . . . . . . . . . . . . . . . 7 7 Living . . . . . . . . . . . . . . . . . . . . . . . . .45 1.1 1.2 1.3 1.4 Guarantee conditions. . . . . . . . . . . . . . . . . . . . . 7 Inspection records . . . . . . . . . . . . . . . . . . . . . . . . 8 Inspection plan for annual inspection . . . . 11 Inspection plan for leak test . . . . . . . . . . . . . . 12 2 Introduction . . . . . . . . . . . . . . . . . . . 13 7.1 7.1.1 7.1.2 7.1.3 7.1.4 7.1.5 2.1 2.2 General . . . . .
Contents 8.5 8.6 8.7 Gas isolator taps . . . . . . . . . . . . . . . . . . . . . . . . . 80 External gas connection . . . . . . . . . . . . . . . . . 80 Duomatic switching facility . . . . . . . . . . . . . . 81 9 Electrical system . . . . . . . . . . . . . . . 85 9.1 9.2 9.3 9.3.1 General safety instructions . . . . . . . . . . . . . . . 85 Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 12 V power supply . . . . . . . . . . . . . . . . . . . . . . .
Contents 12.7 12.7.1 12.7.2 12.7.3 12.8 12.8.1 12.8.2 12.8.3 Winter care . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Winter operation . . . . . . . . . . . . . . . . . . . . . . .156 At the end of the winter season . . . . . . . . .156 Lay-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157 Temporary lay-up. . . . . . . . . . . . . . . . . . . . . . .157 Winter lay-up . . . . . . . . . . . . . . . .
Contents 6 Caravan - 09-09 - EN
1 1.1 Guarantee Guarantee conditions 1Guarantee 1. In addition to the legal guarantee and product warranty rights due to the customer, Dethleffs GmbH & Co. KG may also grant a guarantee of six years that the vehicles constructed by the company are sealed in such a manner that moisture cannot penetrate from the outside into the interior of the vehicle.
1 1.2 Guarantee Inspection records Delivery Signature and stamp of the Dethleffs dealer: 1st year Water ingress test Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 1st year Water ingress test 1st year No defects found Found defects: Should it be determined during an inspection that additional work is necessary, then the carrying out of this work is dependent on the customer commissioning this to be done.
1 Guarantee 2nd year Water ingress test Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 2nd year Water ingress test 2nd year No defects found Found defects: 3rd year Water ingress test Signature and stamp of the Dethleffs dealer: Paste inspection stamp here.
1 Guarantee 4th year Water ingress test Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 4th year Water ingress test 4th year No defects found Found defects: 5th year Water ingress test Signature and stamp of the Dethleffs dealer: Paste inspection stamp here.
1 1.3 Guarantee Inspection plan for annual inspection Pos.
1 1.4 Guarantee Inspection plan for leak test Pos. Component Activity 1.1 Wheel housing Visual check 1.2 Rear wall floor plateau connection Visual check 1.2.1 Side wall in the direction of travel left connection Visual check 1.2.2 Side wall in the direction of travel right connection Visual check 1.3 Front wall floor plateau connection Visual check 1.3.1 Side wall in the direction of travel left connection Visual check 1.3.
2 Introduction Please read this instruction manual completely before using the vehicle for the first time! 2Introduction Always keep this instruction manual in the vehicle. Also inform all other users of the safety regulations. X The non-observance of this symbol can lead to personal injury. Z The non-observance of this symbol can lead to damage being caused to, or inside the vehicle. Z This symbol indicates recommendations or special aspects.
2 Introduction Z The vehicle comes without a wheel brace and vehicle jack. We recommend you buy a commercial wheel brace before first use of your vehicle, in order to have it ready in the case of mishap or emergency. If there is no AL-KO vehicle jack (special equipment for AL-KO chassis), procure a commercial scissors-type jack or hydraulic vehicle jack before first use of your vehicle in order to have it ready in the case of mishap or emergency.
2 Introduction Z Empty waste bins as often as possible into the cans or containers that are pro- vided for this purpose. This helps to avoid unpleasant smells and an accumulation of rubbish on board. Z When parked, do not allow the engine of the towing vehicle to run more than necessary. When running idle, a cold engine releases more contaminants than usual. The running temperature of the engine is achieved more quickly whilst the vehicle is in motion.
2 Introduction 16 Caravan - 12-11 - EN
3 Safety Chapter overview 3Safety This chapter contains important safety instructions. The safety instructions are for the protection of persons and property. The instructions address the following topics: z z z z z z z 3.1 3.1.
3 Safety All the windows and doors that fulfil the following criteria rate as emergency exists: z z z z 3.2 Opening outwards or moving in the horizontal direction Opening angle at least 70° Diameter of the clear opening at least 450 mm Maximum distance to vehicle floor 950 mm General X The oxygen in the vehicle interior is used up by breathing and the use of gas operated appliances. That is why the oxygen needs to be replaced on a constant basis. For this purpose, forced ventilation options (e.g.
3 Safety X Observe the overall height of the vehicle (including roof loads) at under- passes, tunnels, etc. X In winter, the roof must be free of snow and ice before commencing the journey. X Before commencing the journey, empty the waste water tank. X Push in fully the drive-on ramp and lock it into place before commencing the journey. X Check the tyre pressure before a journey and at 2-week intervals. Wrong tyre pressure causes excessive wear and can lead to damage or even to tyre burst.
3 3.5 3.5.1 Safety Gas system General information X Before starting the journey, when leaving the vehicle or when gas equip- ment is not in use, close all gas isolator taps and the main isolator tap on the gas bottle. X No appliance (e.g. heating or refrigerator) that is operated with an open flame may be operational while fuel is being filled up, on ferries or in the garage. Danger of explosion! X If an appliance is operated with an open flame, do not start the appliance up in closed areas (e.g.
3 Safety X The regulator tap on the gas bottle must be accessible. X Only connect gas-operated devices (e.g. gas grill) which have been designed for a gas pressure of 30 mbar. X The exhaust gas pipe must be fitted tightly to the heating system and to the vent and must be sealed. The exhaust gas pipe must not show any evidence of damage. X Exhaust fumes must be able to escape into the atmosphere unhindered and fresh air must be able to enter unhindered.
3 3.7 Safety Water system X Water left standing in the water tank or in the water pipes becomes undrink- able after a short period. Therefore, before each use of the vehicle, thoroughly clean the water pipes and the water tank. After each use of the vehicle completely empty the water tank and the water pipes. X In case of lay-ups lasting more than a week, disinfect the water system before using the vehicle.
4 Before the journey Chapter overview 4Before the journey This chapter contains important information which has to be noted before commencing your journey or carrying out any tasks before the journey.
4 4.3 Before the journey Connecting X Care is to be taken when connecting and detaching a trailer. Risk of accident and injury! X No persons are to be between the towing vehicle and the trailer during posi- tioning for connecting and detaching. X Observe the permissible nose weight and rear axle load of the towing vehicle. Nose weight and rear axle load must not be exceeded. The values of the nose weight and rear axle load are included in the documents of the vehicle and the tow coupling.
4 4.4 Before the journey Tow couplings Z Before connecting, ensure that the tow ball of the coupling device is free of dirt and grease. 4.4.1 AKS 1300 stabiliser 2 3 4 1 Fig. 1 Connecting: AKS 1300 stabiliser Pull the coupling handle (Fig. 1,3) upwards. Place the opened stabiliser on the towing ball. Push the coupling handle (Fig. 1,3) downwards by hand (not with your foot). Turn the handwheel (Fig. 1,1) to the right until it clearly engages.
4 4.5 Before the journey Detaching X Care is to be taken when connecting and detaching a trailer. Risk of accident and injury! X Additionally observe the safety instructions with respect to connecting included in this instruction manual. Detaching: Apply the caravan handbrake. Place the wheel chocks behind both of the wheels. Remove the connector plug of the caravan from the towing vehicle socket and insert it in the retainer which is to be found on the drawbar.
4 Before the journey 4.6.1 Terms Z In technical and scientific texts the term "mass" has replaced the term "weight". However the term "weight" is still the more common term in general usage. To contribute toward understanding the term "mass" is therefore only used in established phrases in the following passages. Z All specifications according to EU norm DIN EN 1645-2.
4 Payload Before the journey The payload is made up as follows: z Additional equipment z Personal equipment Explanations of the individual components of the payload are contained in the following text. Z The payload of the vehicle can be increased by reducing the vehicle mass com- plete in a ready-to-drive condition. To this purpose it is permissible, for example, to empty the liquid tanks or to remove the gas bottles.
4 Before the journey 4.6.2 Calculating the payload X Payload calculation at the manufacturer is partly based on all-inclusive weights. For safety reasons, the maximum permissible gross weight in a laden condition must not be exceeded. X Only the maximum permissible gross weight and the mass in a ready-to- drive condition, not the actual weight of the vehicle, is stated in the vehicle documents.
4 Before the journey Fig. 3 Incorrectly loaded Loads stored apart from each other (Fig. 3) lead to inclination to skid. Roof loads impair the driving characteristics and move the centre of gravity upwards. This increases the inclination to skid. Fig. 4 Correctly loaded 4.6.4 Incorrect weight distribution Correct weight distribution Do not store heavy objects such as awnings, tin cans, etc. in the caravan but rather in the towing vehicle. Secure bicycles on the roof of the towing vehicle.
4 Before the journey 1 2 3 Fig. 5 Tow load Nose weight Axle load Caravan load, nose weight and axle load Tow load The tow load (Fig. 5,1) stipulated in the towing vehicle documents provides information as to the maximum weight which the towing vehicle is permitted to tow. The tow load refers to the actual weight of the caravan and not to the maximum permissible gross weight of the caravan. Example The towing vehicle may tow 1200 kg.
4 Before the journey 4.6.5 Roof loads X Only step on the roof if a roof rail is mounted. Only climb on the roof via the ladder at the rear X Only step on the ladder if the rear corner steadies have been extended or if the caravan is connected to the towing vehicle or if the caravan is supported at the rear to prevent it from tilting. Otherwise the caravan can tip over to the back. Danger of falling! X Be careful when stepping onto the ladder. There is danger of slipping if the ladder is wet or icy.
4 Before the journey Z For further information about positioning the flat screen see Chapter 7. Holder in the TV cabinet The flat screen is attached to a console in the TV cabinet. Fig. 6 Storing the flat screen: Holder in the TV cabinet Rotate the flat screen to its initial position and lock it into place. Insert the holder for the flat screen on the handle (Fig. 6,1) until the latch (Fig. 6,2) locks into place. Close TV cabinet.
4 4.9 Before the journey Road safety X Check the tyre pressure before a journey and at 2-week intervals. Wrong tyre pressure causes excessive wear and can lead to damage or even to tyre burst. You can lose control of the vehicle. Before commencing the journey, work through the checklist: No.
4 Gas system Electrical system Before the journey No.
4 Before the journey 36 Caravan - 12-11 - EN
5 During the journey Chapter overview 5During the journey This chapter contains instructions on how to drive the caravan. The instructions address the following topics: z driving speed z brakes z driving in reverse 5.1 Driving with the caravan X During the journey no persons are to travel inside the caravan. X The caravans have been designed for a technically permissible maximum speed of 100 km/h. Therefore never drive faster than 100 km/h.
5 5.2 During the journey Brakes X Have defects on the braking system immediately remedied by an authorised specialist workshop. Before each journey 5.3 Before each journey, check by means of a braking test: z Does the overrun brake function? z Do the brakes react evenly? z Do the towing vehicle and the caravan remain on track when braking? Driving in reverse Z When driving in reverse, the caravan reacts in exactly the opposite direction to the steering movements of the towing vehicle.
5 During the journey Z The angle between the vehicles must not be too narrow, otherwise the corners will bump against each other. This can cause major damage to the vehicles. Get someone to direct you! As soon as both vehicles are at an approximate angle of 120° to each other, come to a stop (Fig. 11). Turn the steering wheel to the right and reverse with caution (Fig. 12). Continue to reverse, correcting the steering if necessary.
5 During the journey 40 Caravan - 12-11 - EN
6 Pitching the caravan Chapter overview 6Pitching the caravan This chapter contains instructions on how to pitch the vehicle. The instructions address the following topics: z z z z z z z handbrake wheel chocks operation of the supports entrance step mobile waste water tank 230 V connection refrigerator Z Pitch the vehicle so that it is as horizontal as possible. Secure the vehicle to pre- vent it from rolling. Z Animals (especially mice) can cause great damage to the interior of the vehicle.
6 6.2 Pitching the caravan Wheel chocks Use the two wheel chocks even when the upward or downward gradients are of a minimum. The wheel chocks are situated at the front underneath the caravan. Fig. 15 Removal: 6.3 Wheel chock Swivel the retaining clip (Fig. 15,1) down. Remove the wheel chock (Fig. 15,2) from the holder. Corner steadies Z Do not use the fitted corner steadies as a vehicle jack. The corner steadies are only for stabilising the pitched vehicle.
6 Pitching the caravan Fig. 16 Cranking down: Corner steady cranked down Place the hand crank provided as standard on the hexagonal nut (Fig. 16,1) of the corner steady (Fig. 16,2). Rotate the hand crank in a clockwise direction. The corner steady is swung downwards. Cranking upwards: Turn the crank handle anticlockwise. The corner steady is swung upwards. 6.4 Entrance step (free-standing) X Ensure that the entrance step is positioned on an even and stable surface.
6 6.5 Pitching the caravan Waste water tank, mobile Fig. 18 Waste water tank, mobile During the journey the waste water tank (Fig. 18,1) is stored in the gas bottle compartment of the caravan. The drain pipe (Fig. 18,3) of the caravan is located on the floor of the vehicle on the left in the direction of travel. Before using the water system: Place the waste water tank under the caravan so that the opening (Fig. 18,2) of the waster water tank is positioned under the drain pipe. 6.
7 Living Chapter overview 7Living This chapter contains instructions about living in the vehicle. The instructions address the following topics: z z z z z z z z z z 7.1 opening and closing the doors and external flaps heating the vehicle ventilation of the vehicle opening and closing the windows and blinds opening and closing the skylights converting tables positioning the television lamps extending the seating groups using the beds Doors X Only drive with the doors locked.
7 Living 7.1.2 Conversion door, outside (hinged handle) 1 Fig. 21 Opening: 2 Door lock, outside Insert the key in the locking cylinder (Fig. 21,1) and turn clockwise until the door lock is unlatched. Return the key to the central position and remove it. Pull on the handle (Fig. 21,2). The door is open. Locking: Insert the key in the locking cylinder (Fig. 21,1) and turn it anticlockwise until the door lock is engaged. Return the key to the central position and remove it. 7.1.
7 Living 7.1.4 Conversion door, split The split conversion door can be adjusted with the catch levers so that only the upper part of the door can be opened. The lower part of the conversion door remains locked. Fig. 24 Opening the upper part of the door: Catch lever on the lower part of the door Lock the lower part of the door. In order to carry this out turn catch lever (Fig. 24,1) a quarter turn clockwise. Open the upper part of the door.
7 Living 7.1.6 Blind on the conversion door The blind of the conversion door is located in the upper blind box. Fig. 26 Closing: Opening: Blind Pull blind downwards by the handle (Fig. 26,2) and lock it into place. Pull blind downwards gently by the handle (Fig. 26,2) and push the unlocking bar (Fig. 26,1) outwards. The lock (Fig. 26,4) is released from the holder (Fig. 26,3). Use handle to return the blind slowly to its initial position. 7.
7 Locking: Living Insert the key into the locking cylinder (Fig. 27,2) and turn until the flap lock is engaged. Return the key to the central position and remove it. 7.2.2 Flap lock rear flap, inside 1 Fig. 28 Opening: 2 Flap lock rear flap, inside Pull on the handle (Fig. 28,2). The flap lock is unlatched. The locking lever (Fig. 28,1) jumps out automatically. Locking: 7.2.3 Press the locking lever (Fig. 28,1).
7 Living 7.2.4 Flap lock, elliptical Z During rain, water can penetrate the opened flap lock. Therefore close the lock handle. 1 Fig. 30 Opening: 2 Flap lock, elliptical, locked Insert the key into the locking cylinder (Fig. 30,1) and turn a quarter turn antic- lockwise. Lock handle (Fig. 30,2) is released. Remove the key. Turn lock handle one quarter turn in an anticlockwise direction. The flap lock is open. Closing: Firmly close the external flap.
7 Closing: Living Firmly close the external flap. Turn the lock handle until it is positioned horizontally. The flap lock is latched in but not yet closed. Insert the key into the locking cylinder. Press down lock handle with key inserted and turn key a quarter turn. The lock handle will stay bolted. Remove the key. 7.2.6 Flap for toilet cassette Fig. 32 Opening: Flap for toilet cassette Insert the key into the locking cylinder of the push-button lock (Fig.
7 7.3 Living Heating X During heater operation, the exhaust gas pipe in the wardrobe will get hot. Therefore do not store any heat-sensitive garments immediately next to the exhaust gas pipe (see also Chapter 10). Z The operation of the heater is described in Chapter 10. 7.4 Ventilation X The oxygen in the vehicle interior is used up by breathing and the use of gas operated appliances. That is why the oxygen needs to be replaced on a constant basis. For this purpose, forced ventilation options (e.g.
7 Living Z When leaving the vehicle, always close the windows. Z In case of strong temperature differences or in extreme weather conditions, light condensation can form on the double-glazed acrylic glass. The glass is designed in such a way that condensation can evaporate when the external temperature increases. There is no danger of the double-glazed acrylic glass being damaged by condensation. 7.5.
7 Living To place the hinged window into the "continuous ventilation" position: Turn the catch lever (Fig. 36,3) a quarter turn towards the centre of the window. Lightly open the hinged window outwards. Return the catch lever to its initial position. The locking catch (Fig. 36,2) has to be moved into the recess of window catch (Fig. 36,1). During the journey, the hinged window may not be in the "continuous ventilation" position.
7 Living Fig. 39 Continuous ventilation Catch lever in the "continuous ventilation" position With the catch lever, the hinged window can be placed in two positions: z "Continuous ventilation" (Fig. 39) z "Firmly closed" (Fig. 37). To place the hinged window into the "continuous ventilation" position: Turn the catch lever (Fig. 39,3) a quarter turn towards the centre of the window. Lightly open the hinged window outwards. Turn the catch lever a quarter turn towards the window frame.
7 Living 7.5.3 Blind and roller insect screen Z Open the blinds and roller screens before starting the journey. If the blinds and roller screens are closed, the spring loads may be damaged through the vibrations and shocks. Z Depending on the window size the blinds and roller screens are equipped with one or two handles. The windows are fitted with a blind and a roller insect screen. The blind and roller insect screen can be adjusted separately. Fig.
7 Living 7.5.4 Bug window blind The bug window is equipped with a blind. 1 Fig. 41 Blind Closing: Opening: 7.6 2 Bug window blind The blind is located in the bottom blind box. Pull the blind upwards at the notch (Fig. 41,2). Pull the blind (Fig. 41,1) downwards at the notch (Fig. 41,2). Skylights Depending on the model, skylights with or without forced ventilation are fitted to the vehicle.
7 Living Z When leaving the vehicle, always close the skylights. 7.6.1 Skylight with snap latch (Variant 1) Fig. 42 Forced ventilation Depending on the model, a skylight with forced ventilation (Fig. 42,1) is built in the toilet compartment. The skylight can be pushed upwards either from one side or from both sides. Fig. 43 Opening: Insect screen Fig. 44 Skylight, handle Pull on the handle (Fig. 43,2). Fold the insect screen (Fig. 43,1) downwards. Push the spring-loaded latch (Fig.
7 Living Fig. 45 Closing: Blind Pull the blind (Fig. 45,1) using the handle (Fig. 45,2) and hook the hooks (Fig. 45,3) in the opening (Fig. 45,4). Opening: 7.6.2 Pull the hooks (Fig. 45,3) out of the opening (Fig. 45,4) and guide the blind back. Skylight with snap latch (Variant 2) The skylight can be pushed upwards either from one side or from both sides. 4 3 3 2 1 Fig. 46 Opening: Skylight with snap latch (Variant 2) Pull down the insect screen (Fig. 46,2) with the handle (Fig.
7 Living 7.6.3 Heki skylight (mini and midi) Fig. 47 Safety knob on the Heki skylight Fig. 48 Heki skylight, guide The Heki skylight is opened on one side only. Opening: Press the safety knob (Fig. 47,2) and pull the bar (Fig. 47,1) down with both hands. Pull the bar (Fig. 48,1) in the guides (Fig. 48,2) to the rearmost position (Fig. 48,3). Closing: Use both hands to push the bar (Fig. 48,1) slightly upwards. Push the bar back in the guides.
7 Insect screen Closing: Opening: 7.6.4 Living To close and open the insect screen: Pull the insect screen by the handle to the opposite handle of the Roman shade. Press the rear part of the handle of the insect screen. The latch is released. Use handle to return the insect screen slowly to its initial position. Heki skylight 3 4 5 2 1 Fig. 51 Heki skylight, closed Fig. 52 Heki skylight in ventilation position 1 The Heki skylight may be opened on one side only.
7 Living 1 2 3 Fig. 53 Ventilation position (Variant 2): Heki skylight in ventilation position 2 Open Heki skylight. Insert the bar (Fig. 53,3) into the holder (Fig. 53,1). Place the lever (Fig. 53,2) over the bar. 1 Fig. 54 Roman shade Closing: 2 Heki skylight, blind lock To close and open the Roman shade: Pull out Roman shade at the handle (Fig. 54,2) and release in the required posi- tion. The Roman shade will stay in that position.
7 7.7 Living Lifting roof The internal height of the caravan can be adjusted using the lifting roof. 1 Fig. 55 2 1 Lifting roof Fig. 56 Fuse Z The lifting roof must be closed before commencing the journey. Opening: Release the safeguards (Fig. 55,1) by pulling them lightly. Closing: Pull the lifting roof downwards at the handles (Fig. 55,2). 7.8 7.8.1 Push the lifting roof upwards at the handles (Fig. 55,2). Lightly pull the safeguards (Fig. 55,1) downwards and hook them in again.
7 Living 7.8.2 Swivel table X Before commencing the journey, reduce the size of the swivel table and secure it. 1 1 2 3 Fig. 58 Locking: 2 Latch for swivel table with metal frame Fig. 59 Latch for swivel table with plastic frame Place the swivel table next to the holder (Fig. 58,3) or on the holder (Fig. 59,2). Place the bar (Fig. 58,2) with the securing bolt (Fig. 58,1) over the table leg. Move the bar and possibly also the swivel table in such a way that the securing bolt (Fig.
7 Living 7.8.3 Swivel table of the rear seating group The table top can be swiveled into different positions. 1 2 3 4 5 6 Fig. 61 Swivelling the table top Tommy screw Table-top Tommy screw Table leg Tommy screw Holder Swivel table Loosen the tommy screws (Fig. 61,1, 3 and 5). Swivel table top (Fig. 61,2) into required position. Tighten the tommy screws again. The swivel table can be removed for the bed conversion. Removing the swivel table for bed conversion Undo the tommy screw (Fig.
7 7.9 Living Television X Before starting your journey, remove the television from the support and store it securely. X Before commencing the journey, place and secure the flat screen and screen support in the initial position. If the screen holder is installed in a TV cabinet: Close TV cabinet. X Before commencing the journey, ensure that the antenna is in park position. Danger of accidents! Flat screen in the TV cabinet The flat screen is attached to a console in the TV cabinet. Fig.
7 Flat screen with swivel arm Living The flat screen is fastened to a swivel arm. Fig. 65 Positioning the flat screen with swivel arm: 7.10 Swivel arm for flat screen Pull up the release knobs (Fig. 65,1 and 3) to unlock the swivel arm. Swivel the flat screen with the holder (Fig. 65,2) into the desired position. Lamps X Bulbs and light fittings can be extremely hot. X Let the bulbs and lamp holders cool down before touching them.
7 7.10.2 Living Halogen spotlight 1 2 Fig. 67 Moving halogen spotlight: Halogen spotlight Grasp the holder (Fig. 67,1) and turn it 45°. Remove the halogen spotlight (Fig. 67,2) from the rail system. Insert the halogen spotlight (Fig. 67,2) into the rail system at the desired posi- tion and turn 45°. Turn 45° at holder (Fig. 67,1). 7.11 Extending the central seating group Fig. 68 Extending: Support for bench seat extension Fold up the bench seat extension (Fig. 68,1).
7 Living 7.12 Beds 7.12.1 Bunk bed X Only use the bunk bed if the safety net is in position. X The maximum permitted bunk bed load is 100 kg. X Never allow small children to remain in the bunk bed without supervision. X But in particular with regard to small children less than 6 years of age, users should ensure that they cannot fall out of the bunk bed. X Use separate children's beds or travel cots suitable for children. Depending on the model, the vehicle is fitted with a bunk bed.
7 7.12.3 Living Fixed bed (gas pressure spring) Fig. 70 Fixed bed A storage compartment is underneath the bed. Lift up the slatted frame from the vehicle inside to place items in the storage compartment or to empty it. Opening: Lift the mattress forwards and set it down on the panel. Lift slatted frame. The gas-pressure springs (Fig. 70,1) hold the slatted frame open. Closing: Press the slatted frame downwards against the resistance of the gas-pressure springs.
7 7.12.4 Living Bed in sleeper roof X The maximum permitted load on the bed in the sleeper roof is 200 kg. X Before commencing the journey, retract the sleeper roof. X Only use the bed in the sleeper roof if the safety guards are in position. X Never leave small children without supervision. X But in particular with regard to small children less than 6 years of age, users should ensure that they cannot fall out of the bed.
7 Living 7.13 Converting seating groups for sleeping Z In the event of an accident, emergency braking or on uneven road surfaces, additional cushions with reinforced undersides can be thrown through the vehicle and damage parts of the equipment. Before setting off, stow the additional cushions safely away or secure them with the straps provided for that purpose. 7.13.
7 7.13.2 Living Round seating group with round table 1 2 3 4 5 6 Fig. 75 Prior to conversion Fig. 76 During conversion Fig. 77 After conversion Back cushion Seat cushion Table Back cushion Back cushion Additional cushion Convert the table (Fig. 75,3) to a bed foundation (see Section 7.8). Remove the back cushions (Fig. 76,1, 4 and 5). Pull the seat cushions (Fig. 77,2) into the centre. Insert the back cushions (Fig. 77,1) between the seat cushions (Fig. 77,2) and the exterior wall.
7 7.13.3 Living Rear seating group 1 2 3 4 5 6 7 8 9 Fig. 78 Prior to conversion Fig. 79 During conversion Fig. 80 After conversion Back cushion Seat cushion Table Back cushion Back cushion Seat cushion Bed rod Additional board Additional cushion Dismantle the table (Fig. 78,3) (see Section 7.8). Remove the back cushions (Fig. 78,1, 4 and 5) and lay them aside. Attach the bed rod (Fig. 79,7) and push it backwards as far as possible. Lay the additional board (Fig.
7 7.13.4 Living Widening the bed into a playing area 1 2 3 4 5 6 7 8 9 Fig. 81 Prior to conversion Fig. 82 During conversion Fig. 83 After conversion Back cushion Seat cushion Table Back cushion Back cushion Bedding box extension Additional board Additional cushion Bed Convert the table (Fig. 81,3) to a bed foundation (see Section 7.8). Turn table one quarter turn in a clockwise direction and pull forwards to the right. Pull out the bedding box extension (Fig. 81,6).
7 Living 76 Caravan - 12-11 - EN
8 Gas system Chapter overview 8Gas system This chapter contains instructions regarding the gas system of the vehicle. The instructions address the following topics: z z z z z z safety gas consumption changing the gas bottles gas isolator taps external gas connection automatic switching facility The operation of the gas operation appliances of the vehicle is described in Chapter 10. 8.
8 Gas system X Regularly inspect the gas tube fitted to the gas bottle connection for tight- ness. The gas tube must not have any tears and must not be porous. Have the gas tube replaced by an authorised specialist workshop no later than 10 years after the manufacturing date. The operator of the gas system must see to it that the parts are replaced. X Due to its function and construction, the gas bottle compartment is a space which is open to the exterior.
8 Gas system Z Screwed connections on the gas pressure regulator have left-handed threads. Z For gas-operated units the gas pressure must be reduced to 30 mbar. Z Connect gas pressure regulator complete with safety valve directly to bottle valve. The gas pressure regulator reduces the gas pressure in the gas bottle down to the operating pressure of the gas devices. Z For filling and connecting the gas bottles in Europe the accessories shops have corresponding Euro filling sets and Euro bottle sets.
8 Gas system Unscrew the gas pressure regulator (Fig. 84,3) with the gas tube (Fig. 84,5) from the gas bottle by hand (left-handed thread). Release the fixing belts (Fig. 84,2) and take out the gas bottle. Place a filled gas bottle in the gas bottle compartment. Fix gas bottle in place with the fixing belts. Screw gas pressure regulator and gas tube manually onto gas bottle (left- handed thread). 8.5 Gas isolator taps 1 2 3 4 Fig.
8 Gas system 1 2 Fig. 86 External gas connection, gas isolator tap closed The external gas connection (Fig. 86) is located at the rear or to the left or right of the vehicle depending on the model. Connect the external gas device to the connection point (Fig. 86,2). Open the gas isolator tap (Fig. 86,1). 8.7 Duomatic switching facility X Do not use the switching facility in closed spaces.
8 Gas system The pressure gauge (Fig. 87,2) on the central regulator indicates the pressure in the gas bottle, not the filling level of the gas bottle. The pressure gauge can be used to test the impermeability of the gas bottle. Only the electrical functions can be switched at the operating unit (Fig. 88). The regulator taps on the gas bottles (Fig. 87,1 and 4) must be opened manually. The central regulator provides a constant gas pressure, regardless of which gas bottle is being drawn upon.
8 Changing gas bottles Gas system If an indicator lamp goes out during operation, this signifies that the corresponding gas bottle is empty and must be replaced. The reserve bottle continues supplying the gas appliances with gas. X When changing gas bottles, do not smoke or create any open fire. Z Always mount the regulator so that the protective cap is at the top. Changing gas bottles: Close the regulator tap on the empty gas bottle. Unscrew the regulator of the gas bottle.
8 Gas system 84 Caravan - 12-11 - EN
9 Electrical system Chapter overview 9Electrical system This chapter contains instructions regarding the electrical system of the caravan.
9 9.3 Electrical system 12 V power supply Z If you use the battery of the towing vehicle to provide power for the caravan, bear in mind that the battery capacity is restricted. If you place too great a burden on the battery, this may lead to starting difficulties. Z Always disconnect the electrical connection between the towing vehicle and the caravan before the caravan is connected to the local power supply. In order to carry this out, disconnect the plug from towing vehicle socket.
9 Electrical system Z The battery is maintenance-free. Maintenance-free means: It is not necessary to check the acid level. It is not necessary to lubricate the battery poles. It is not necessary to refill the distilled water. Even a maintenance-free battery must be charged regularly. When the vehicle is not connected to the 230 V power supply or the 230 V power supply is switched off, the living area battery supplies the living area with 12 VDC. The living area battery has a limited power supply only.
9 Energy reserves 9.3.3 Electrical system Off-load voltage (measured at the poles) Charging condition Higher than 12,80 V 100% Approx. 12.55 V 75% Approx. 12.32 V 50% Approx. 12.18 V 25% Lower than 12.00 V 0% The living area battery has a limited power supply only. That is why electrical appliances should not be operated over a long period of time if the vehicle is not connected to the 230 V power supply or the engine of the towing vehicle is switched off.
9 Charging with an external charger Electrical system When charging the living area battery with an external charger, proceed as follows: Disconnect the caravan electrically from the towing vehicle. Switch off the 12 V main switch on the panel. The indicator lamp goes out. Disconnect the mains plug from the transformer/rectifier. Switch off all gas appliances, all gas isolator taps and close the regulator tap on the gas bottle.
9 Electrical system Transformer H MIKO MK 140 ta30 230 V - 50 Hz 1A 12 V DC - 140 W 15 A 1 Fig. 89 2 3 Power pack The 230 V automatic circuit breaker (Fig. 89,1), the overload protection (Fig. 89,2) and the main fuse (Fig. 89,3) are integrated in the power pack. The overload protection switches all 12 V appliances in the caravan off, if the power pack overheats.
9 Switching on overload protection (only type I): Electrical system When the overload protection triggers, allow the power pack to cool. Press the upper part of the main switch (Fig. 90,4) first: Position "OFF". After about 60 seconds, switch the main switch back to position "ON". 9.5 Transformer/rectifier EBL 109 (Power Pack SE) Z Do not cover the ventilation slots.
9 Electrical system When the transformer/rectifier is subject to a heavy load, the fitted charger module reduces the charging current. This protects the charging device against overheating. The transformer/rectifier is subject to a heavy load when e.g. an empty living area battery is charged, additional electrical appliances are turned on and the ambient temperatures are high. Location Depending on the model, the transformer/rectifier is situated either in the bench or in the bedding box.
9 Electrical system 9.6.1 12 V main switch The 12 V main switch (Fig. 93,1) switches the 12 V power supply of the living area on and off. Switching on: Press the upper part of the rocker switch (Fig. 93,1): The 12 V living area power supply is switched on. The 12 V indicator lamp (Fig. 93,2) lights up in green. Switching off: Press the lower part of the rocker switch (Fig. 93,1): The 12 V living area power supply is switched off. The 12 V indicator lamp (Fig. 93,2) goes off.
9 9.7 Electrical system Panel LT 222 1 2 Rocker switch for water tank Water tank indicator lamp LT 222 2 Fig. 94 Filling level of the tank Displays: 1 Panel LT 222 The filling level in the water tank can be read off on the panel (Fig. 94). Press the rocker switch (Fig. 94,1): One of the indicator lamps (Fig. 94,2) lights up. 9.8 230 V power supply X Only allow qualified personnel to work on the electrical system.
9 Electrical system 9.8.2 Power cable for external 230 V connection X Completely unwind the cable on cable drums to prevent overheating. Power cable Connection possibilities z z z z Three-core (3 x 2.5 mm2) flexible rubber sheathed cable Maximum 25 m in length 1 plug with earth contact 1 socket with earth contact (connectors to EN 60309) We recommend a CEE connection cable with CEE plug and CEE socket as the supply line.
9 9.9 Electrical system Fuses X Only replace defective fuses when the cause of the defect is known and has been remedied. X Only replace defective fuses when the power supply is switched off. X Never bridge or repair fuses. 9.9.1 12 V fuses The appliances connected to the 12 V power supply in the living area are fused individually. The fuses are accessible on the power pack and on the transformer/rectifier. 1 2 Fig.
9 Electrical system Function Fuses on the transformer/rectifier EBL 109 (Power Pack SE) Value/colour Internal charger 20 A yellow Booster 15 A blue Solar 15 A blue TV 7,5 A brown Circuit 2 15 A blue Water pump Fuse for the Thetford toilet (swivel toilet) 5 A light brown Circuit 1 15 A blue Refrigerator control 2 A grey The fuse is located in the locker wall of the Thetford cassette. 1 Fig.
9 Electrical system 9.9.2 230 V fuse MIKO MK 140 ta30 230 V - 50 Hz 1A 12 V DC - 140 W 15 A 1 Fig. 100 2 3 Safety cut-out (variant 1) Fig. 101 Safety cut-out (variant2) A two-pole safety cut-out (Fig. 100,1 or Fig. 101,1) secures the 230 V power supply. The safety cut-out is integrated in the power pack (Fig. 100) or mounted separately next to the power pack (Fig. 101). 9.10 9.10.
9 Electrical system Contact number Function Cable colour Left tail light, side marker light, clearance light, marker light, licence plate light Black 1.5 mm2 8 Reverse lamp and/or reverse equipment for overrun brake Pink 1.5 mm2 9 Power supply (constant positive): Light, water pump, refrigerator, charging line of transformer/rectifier defective (only for Power Pack SE) Orange 2.5 mm2 10 Power supply (controlled by the ignition switch): Control booster in transformer/rectifier Orange 2.
9 9.10.2 Electrical system Towing vehicle installation (Power Pack SE) Z The towing vehicle must be retrofitted with the corresponding cable cross sec- tions and a relay for the power supply (controlled using the ignition) (see Fig. 103). Z If the cable cross sections stipulated below are not adhered to, then it is possible that a correct charging of the living area battery during the journey is not possible. Fig.
10 Appliances Chapter overview 10Appliances This chapter contains instructions regarding the appliances of the vehicle. The instructions refer exclusively to the operation of the appliances. Further information about the appliances can be found in the instruction manuals for the appliances, included separately with the vehicle. The instructions address the following topics: z z z z z z z z 10.
10 Appliances 10.2 Heater X In winter, check that the waste gas vent on the roof is free of snow and ice before using the heater. X Never let gas escape unburned due to danger of explosion. X When filling the fuel tank of the towing vehicle, on ferries or in the garage, never run the heater in gas operation. Danger of explosion! X Never operate the heater in gas operation in closed rooms (e.g. garages).
10 10.2.2 Appliances Trumatic S hot-air heater X In case of problems wait for two minutes before trying again. 7 6 9 8 10 5 0 4 3 2 1 Fig. 106 Switching on without automatic ignition: Hot-air heater control knob Open the regulator tap on the gas bottle and the gas isolator tap "Heater". Turn the control knob on the heater to the required position and press down to its stop limit. Strike gas lighting button (at the control knob) several times in succession.
10 Appliances Fig. 107 Changing the battery on the automatic ignition: Removing the heater cover Fig. 108 Heating opened Ensure that the heater is switched off. Remove the heater cover (Fig. 107,2). To do so pull the cover upwards and for- wards, press the retaining springs (Fig. 107,1) at the side upwards and swing the cover to the front. Place the cover (Fig.
10 10.2.3 Appliances Circulation fan The circulation fan together with the hot-air heater ensures a better distribution of hot air throughout the caravan. Depending on the model either one or two circulation fans are installed in the vehicle. 3 4 ruma Trumavent 1 2 5 1 2 230V~ Fig. 110 Switching circulation fan (230 V) on: Switching circulation fan (230 V) off: Operating switch for circulation fan (230 V) Turn the rotary switch (Fig. 110,1) to " ". Turn the knob (Fig.
10 Appliances Fig. 112 Circulation fan Fig. 113 Circulation fan, adjustment flap in central position The hot air flow can be adjusted as required with the operating lever (Fig. 112,1) on the back of the circulation fan. Factory setting is the central position. In the central position the warm air is distributed evenly to each warm air outlet. The operating lever (Fig. 113,1) for the adjustment flap is located under the base flap in the wardrobe.
10 10.2.5 Appliances Alde hot-water heater Z Never run the hot-water heater without heating fluid. Observe the specifica- tions in Chapter 13. Z Never drill holes in the floor. This might damage the hot-water pipes. Z Do not use the space above and behind the heater as a storage compartment. Z The circulating pump must always be turned on when the hot-water heater is in operation. Z We recommend bleeding the heating system after the initial heater operation to checking the glycol content.
10 Start screen Appliances The Start screen appears on the display after the heater is switched on.
10 Selecting the operating mode Appliances The hot-water heater can be operated with the following energy sources: z Gas operation z 230 V electrical operation z Gas and 230 V electrical operation The operating mode is selected on the operating unit. Selecting gas operation: Selecting 230 V electrical operation: Press the "On" button next to the " " symbol. The gas operation is activated. Press the "+" button next to the " " symbol until the desired heat output is reached.
10 Setting the rotational speed of the circulating pump Setting the output: 10.2.6 Appliances Z Level 2 = Normal level Z Level 5 = Ventilation Set the adjusting screw at the pump to Level 2. To ventilate the pump set the adjusting screw to Level 5. Ultraheat additional electric heater The Ultraheat additional electric heater is built-in to the hot-air heater.
10 10.2.7 Appliances Warming unit for waste water pipes Z Always only press the test button briefly. Z The warming unit only functions when the vehicle is connected to a 230 V power supply. In order to prevent waste water pipes freezing up, the waste water pipes can be electrically warmed. When the warming unit is turned on, the temperature of the waste water pipes is monitored by temperature sensors.
10 10.2.8 Appliances Electrical floor warming unit X On models with electrical floor warming unit, never drill holes in the floor or screw in any screws. Caution with sharp-edged or pointed objects. There is danger of a power cut or a short circuit due to damage to a heater wire. Z Do not cover the regulator. Danger of overheating! Z The electrical floor warming unit only operates if the vehicle is connected to the 230 V power supply.
10 10.2.9 Appliances Floor warming unit/warming unit for waste water tank Z For models with a floor warming unit and a warming unit for the waste water tank, never drill holes in the floor or screw in any screws. Danger of damage to a heating line and water leaking into the floor. Z The floor warming unit and waste water tank warming unit only operate when the hot-water heater is switched on.
10 Appliances 10.3 Air conditioning unit 10.3.1 Air conditioning unit Truma Z The air conditioning unit only runs if the vehicle is connected to a 240 V power supply. Z The external 240 V power supply must be protected by a fuse of at least 3 A. It is otherwise not possible to operate the air conditioning unit properly. Fig. 120 Receiver Fig. 121 Remote control To execute the individual switching commands, always point the remote control in the direction of the receiver.
10 Appliances Timer The air conditioning unit can be switched on or off automatically from the current time up to 15 hours in advance with the integrated timer. Pre-programming up to a certain time is not possible. To program, switch on the air conditioning unit with the key (Fig. 121,7) on the remote control. Set the desired operating mode and room temperature with the keys (Fig. 121,8, 3 and 4). Use the key (Fig. 121,5) to select the desired function (Fig.
10 10.3.2 Appliances Air conditioning unit (Teleco) 4 2 3 1 Fig. 122 Roof view 1 2 3 4 Fig. 124 Fig. 123 Interior view 5 6 7 Remote control The air conditioning unit is located on the roof of the vehicle. The remote control (Fig. 124) for the air conditioning unit is located in the kitchen area. Switching on: Connect the vehicle to the 230 V power supply. The air conditioning unit is ready to operate. The red LED (Fig. 123,2) lights up. Switch on the remote control at the switch (Fig.
10 Appliances 10.4 Boiler X Never let gas escape unburned due to danger of explosion. X When filling the fuel tank of the towing vehicle, on ferries or in the garage, never run the boiler in gas operation. Danger of explosion! X Never operate the boiler in gas operation in closed rooms (e.g. garages). Danger of poisoning and suffocation! X The water in the boiler can be heated up to 65 °C. Risk of scalding! Z When the vehicle is not being used, switch off and drain the boiler.
10 Gas operation Appliances The boiler is operated exclusively with gas. 60 50 ruma Boiler 40 30 1 2 3 4 1 2 3 4 5 Temperature control knob Red indicator lamp "Fault" Rotary switch Off On 70 5 230V~ Fig. 125 Switching on: Operating unit for Truma boiler (gas operation) Remove cap from waste gas vent. Open the regulator tap on the gas bottle and the gas isolator tap "Boiler". Set the rotary switch (Fig. 125,3) to " " (Fig. 125,5).
10 Switching off: Combined operation Appliances Set the flip switch (Fig. 126,1) to " ". The indicator lamp on the switch goes off. The water is heated more quickly in the boiler if gas operation and 230 V electrical operation are switched on simultaneously. Z Further information can be obtained in the manufacturer's instruction manual. Filling/emptying the boiler The boiler can be supplied with water from the water tank.
10 10.4.3 Appliances Alde boiler Switching the boiler on/off The boiler is integrated in the hot-water heater. Separate operation is not possible. For information about operating the hot-water heater see Section 10.2.5. Filling/emptying the boiler The boiler can be supplied with water from the water tank. Z Depending on the model, the vehicle is fitted with one or two drain cocks. Fig. 128 Filling the boiler with water: Drain cocks Close the drain cocks. Position the rocking levers (Fig.
10 10.4.4 Appliances Reich boiler Fig. 129 Reich boiler The boiler is operated with 230 V. The boiler heats about 5 l of water. The water temperature can be set on the temperature controller (Fig. 129,1) of the boiler. The water in the boiler can be heated up to a maximum of 80 °C. Switching on: Connect the vehicle to the external 230 V power supply and switch on the 230 V automatic circuit breaker. Set the desired temperature on the temperature controller (Fig. 129,1). The indicator lamp (Fig.
10 10.4.5 Appliances Water heater Z If you want to empty the water heater: Empty the water tank completely before opening the drain cocks of the water heater. Z Do not install a non-return valve in the cold water pipe between the water heater and the water pump. Z Use a pressure reducer in case of a central water supply or more powerful pumps. The water heater is only designed for a maximum pressure of 1.2 bars. Insert a safety/drainage valve additionally in the cold water pipes.
10 Appliances Fig. 131 Filling the water heater with water: Drain cock for water heater Connect the vehicle to the external 230 V power supply and switch on the 230 V automatic circuit breaker. Switch off the operating switch (Fig. 130). The indicator lamp (Fig. 130,1) in the switch is not on. Close the drain cock. To do so, turn the cap (Fig. 131,1) clockwise. Set all the water taps to "Hot" and open them. The water pump is turned on. The hot water pipes are filled with water.
10 10.5.1 Appliances Gas cooker X During activation and operation of the gas cooker, no flammable or easily combustible objects such as dishcloths, napkins etc. may be near the gas cooker. Fire hazard! X The process of ignition must be visible from above and must not be covered by cooking pans placed on the cooker. X Depending on the model, the gas cooker lid is held closed by a spring. When closing there is danger of getting injured! Z Do not use the glass gas cooker lid as a hob.
10 Switching off: 10.5.2 Appliances Turn the control knob to the 0-position. The flame fades. Close the gas isolator tap "Cooker" and the regulator tap on the gas bottle. Gas oven X Always keep ventilation apertures at the gas oven open. X There must be no flammable objects near the gas oven when it is being lit. X The oven flap must remain open when it is being lit. X If ignition has not taken place, repeat the entire procedure. If necessary, check if there is gas and/or current in the gas oven.
10 Appliances 10.5.3 Microwave oven X Only qualified personnel may repair the microwave oven. Improper repairs can cause major risks to the user. X The protection device against the escape of microwave energy should never be removed. X Use the microwave oven only if it has been properly installed. X Only use the microwave oven when the door seal is free of damage. X Never leave the microwave oven unattended when it is in operation.
10 10.5.4 Appliances Extractor hood 1 Fig. 136 2 Extractor hood The cooker is equipped with an air-circulation extractor hood. It features a twolevel fan and a two-level light. Switching extractor hood on/ off Switching lighting on/off 10.6 Use the switch (Fig. 136,1) to turn the extractor hood on and off. Use the switch (Fig. 136,2) to turn the cooker lamps on and off. Refrigerator During the journey, only operate the refrigerator via the 12 V power supply.
10 10.6.2 Operating modes Appliances Operation (Dometic 8 series) The refrigerator has 2 operating modes: z Gas operation z Electrical operation (230 VAC or 12 VDC) The operating mode is set with the operating controls on the refrigerator panel. Z Select only one energy source. Gas operation X Never let gas escape unburned due to danger of explosion. X Gas operation of the refrigerator with liquefied petroleum gas is not permis- sible. 1 2 3 1 Fig.
10 Electrical operation Appliances Z Close the gas isolator tap "Refrigerator" when the refrigerator is operated elec- trically. The refrigerator can be operated with the following voltages: z 230 VAC z 12 VDC Switching the 230 V operation on: Switching the 230 V operation off: Switching the 12 V operation on: Switching the 12 V operation off: Set the energy selector switch (Fig. 139,2) to " ". Use the control knob (Fig. 139,3) to adjust the refrigerating temperature.
10 Appliances 1 2 3 4 5 6 7 Dometic Mode Fig.
10 Switching the 12 V operation on: Appliances Press the on/off switch/energy selector switch (Fig. 140,1) down for 2 seconds in order to switch on the appliance. The LED of the last selected operating mode lights up. Press the on/off switch/energy selector switch (Fig. 140,1) briefly repeatedly if necessary until the 12 V " " operating indicator lights up. Set the refrigerating temperature with the switch for the temperature setting (Fig. 140,6).
10 Appliances Z Even when the 12 V supply is switched off, a small electrical current flows which puts an extra load on the living area battery. Always switch the refrigerator off during a temporary lay-up. 230 V operation If the 230 V power supply is connected, this energy source is selected as the first priority by the AES. 12 V operation 12 V operation is only selected by the AES if the vehicle's engine is running and the alternator supplies sufficient 12 V operating power.
10 Appliances Select the energy type with the on/off switch/energy selector switch (Fig. 141,1). Set the refrigerating temperature on the switch for temperature setting (Fig. 141,6). The indicator LEDs (Fig. 141,5) show the selected thermostat position. When operated with 12 V, the refrigerator draws power only from the living area battery. Z When the refrigerator is set manually to "12 V", it constantly uses current.
10 Switching on: Appliances Open the regulator tap on the gas bottle and the gas isolator tap "Refrigerator". Set the energy selector switch (Fig. 142,1) to gas " ". Press the control knob (Fig. 142,3) down and hold it. The gas supply is open. Ignition will take place automatically. A ticking sound can be heard until ignition has been completed successfully. Keep the control knob (Fig. 142,3) pressed down until the flame indicator (Fig. 142,2) becomes green and then release it.
10 10.6.6 Appliances Refrigerator door locking mechanism With some models, the refrigerator has a separate freezer compartment. The specifications in this section correspondingly also apply to the door of the freezer compartment. Z During the journey the refrigerator door must always be closed and be locked in the closed position. Z When the refrigerator is switched off, bring the refrigerator door into the venti- lation position and lock it in place if possible. This prevents mould from forming.
10 Appliances Fig. 145 Locking in the ventilation position: Closing device in normal position Fig. 146 Closing device in ventilation position Open the refrigerator door. Press the release (Fig. 145,2) in. Push the closing device (Fig. 145,1) towards the front (Fig. 146). Now when the refrigerator door is closed, it remains open a bit. Thetford 1 1 2 2 Fig. 147 Opening: Lock of refrigerator door, closed (Thetford) Fig.
11 Sanitary fittings Chapter overview 11Sanitary fittings This chapter contains instructions regarding the sanitary fittings of the vehicle. The instructions address the following topics: z z z z z 11.1 water tank waste water tank complete water system toilet compartment toilet Water supply, general X Only fill the water tank from supply systems that have been verified to pro- vide drinking water quality. X Use only hoses or vessels for filling that are approved for drinking water.
11 Sanitary fittings 11.2 Water tank 11.2.1 Drinking water filler neck with cap X The cap for the drinking water filler neck and for the fuel filler neck are very similar. Before filling the tank, always check the label. 1 2 Fig. 149 Cap for the drinking water filler neck The drinking water filler neck is on the right or left side of the vehicle, depending on the model. Opening: Open the cover (Fig. 149,1) of the drinking water filler neck. Insert the key into the locking cylinder (Fig.
11 11.2.3 Sanitary fittings Draining water To empty the water tank, proceed as follows: 2 Fig. 150 1 Water tank Unscrew the cap (Fig. 150,2) on the water tank. Remove the stopper (Fig. 150,1) from the drainage opening. The water drains off. Insert stopper. Screw the cap onto the water tank. 11.3 Waste water tank X Before commencing the journey, empty the waste water tank. Z If there is any risk of frost, empty the waste water tank.
11 Sanitary fittings 11.3.1 Waste water tank, mobile Fig. 151 Emptying: Waste water tank, mobile Close the opening of the waste water tank (Fig. 151,1) with the lid (Fig. 151,3). Pull out the waste water tank at the handle (Fig. 151,2). Swing up the carrying handle (Fig. 151,4) and set the waste water tank up. Only empty the waste water tank (completely!) at disposal stations that are especially provided for this purpose. 11.3.2 Waste water tank, permanently installed Fig.
11 11.3.3 Sanitary fittings Waste water tank in the holder under the vehicle Fig. 153 Removal: Waste water tank in the holder under the vehicle Loosen the safety chain (Fig. 153,4). Press the handle (Fig. 153,3) inwards and turn one quarter turn clockwise. Move the waste water tank and the holder (Fig. 153,2) forwards and down- wards. Remove the waste water tank (Fig. 153,1). 11.3.4 Odour seal Fig.
11 Sanitary fittings 11.4 Filling the water system X When filling the water tank, observe the maximum permissible gross weight of the vehicle. Luggage must be reduced accordingly when the water tank is full. Z The water pump will overheat without water and can get damaged. Never operate water pump when the water tank is empty. Z The water level can be checked on the panel while the water tank is being filled (Power Pack SE). Position the vehicle horizontally.
11 Sanitary fittings 11.5 Emptying the water system Z If the vehicle is not used for several days or if it is not heated when there is a risk of frost, empty the entire water system. Leave the water taps on in central position. Leave the safety/drainage valve (if available) and all drain cocks open. Frost damage to appliances, frost damage to the vehicle and deposits in water-carrying components can be avoided in this way. Z Take note of the environmental tips in this chapter.
11 Sanitary fittings 11.6 Toilet compartment Z Do not transport loads in the shower tray. The shower tray or other items of equipment in the toilet compartment can otherwise be damaged. Z For ventilation purposes during or after a shower, and for drying wet clothing, close the toilet compartment door and open the toilet compartment window or skylight. This improves the air circulation.
11 11.7.1 Sanitary fittings Swivel toilet The flushing of the Thetford toilet is fed directly from the water system of the vehicle. The toilet bowl can be moved into the optimal position. Fig. 156 Flushing: Thetford toilet bowl, swiveling Fig. 157 Flush button/indicator lamp Thetford toilet Before flushing open the sliding trap of the Thetford toilet. To do this, push the slide lever (Fig. 156,1) anticlockwise. For flushing, press the blue flush button (Fig. 157,1).
11 Sanitary fittings Swing the fresh water filler neck (Fig. 159,1) towards the outside. Remove the screw cap (Fig. 159,2). Fill with fresh water until the fluid level reaches the top edge. This corresponds to approx. 15 l. Close the screw cap. Swivel the fresh water filler neck inwards. Close the flap for the Thetford cassette. 1 2 3 Fig. 160 Flushing: Operating unit Thetford toilet Before flushing open the sliding trap of the Thetford toilet. To do this, turn the slide lever (Fig.
11 11.7.3 Sanitary fittings Vacuum toilet (Dometic) Z Only flush the toilet if the toilet lid is closed. The flushing of the toilet is fed directly from the water system of the vehicle. Fig. 161 Putting into operation: Vacuum toilet Fig. 162 Vacuum toilet panel Turn on power supply. The yellow LED (Fig. 162,1) on the panel (Fig. 161,1) turns on for ca. 1 minute. A vacuum is generated in the system. If the green LED (Fig. 162,3) on the panel lights up, lift the pedal (Fig.
11 11.7.4 Sanitary fittings Removing the cassette Z The sewage tank (cassette) can only be removed when the sliding trap is closed. 1 2 Fig. 163 Flap for the toilet cassette Fig. 164 Thetford cassette Open the flap for the cassette on the outside of the vehicle. Insert the key into the locking cylinder of the push-button lock (Fig. 163,1) and turn a quarter turn. Remove the key. Press both push-button locks (Fig. 163,2) simultaneously with your thumb and open the flap for the cassette.
12 Care Chapter overview 12Care This chapter contains instructions regarding the care of the vehicle. The instructions address the following topics: z z z z z z exterior of the vehicle interior water system extractor hood air conditioning unit winter operation At the end of the chapter there is a checklist of measures you must carry out if you are not going to use the vehicle for an extended period of time.
12 Care Treat rubber seals of doors and storage flaps with talc. Treat locking cylinder of doors and storage flaps with graphite dust. 12.1.3 Windows of acrylic glass Acrylic glass windows are delicate and require very careful handling. Z Never rub acrylic glass windows when dry as dust particles might damage the surface. Z Only clean acrylic glass windows with plenty of warm water, dish washing liquid and a soft cloth.
12 12.1.6 Care Waste water tank Clean the waste water tank after every use of the vehicle. Cleaning: 12.2 Open the cleaning opening on the waste water tank and the drain cock. Thoroughly rinse out the waste water tank with fresh water. Internal care Z If possible, treat stains immediately. Z Acrylic glass windows are delicate and require very careful handling (see Sec- tion 12.1.3). Z Synthetic parts in the toilet and living area are very delicate and should be treated with care.
12 Care Clean PVC-floor covering with a mild, soapy cleanser for PVC floors. Do not place carpet on wet PVC-floor covering. The carpet and the PVC-floor covering may stick together. Never clean the sink or the gas cooker with a scourer. Avoid anything which may cause scratching or grooves. Clean gas cooker only with a moist cloth. Prevent any water from penetrating the gas cooker. Water may damage the gas cooker.
12 Care Set all the water taps to "Cold" and open them. Leave the water taps open until the mixture of water and cleanser has reached the drain. Close all water taps. Flush the toilet several times. Let the cleanser act in accordance with the manufacturer specifications. Empty the water system. Collect the exiting mixture of water and cleansers and dispose of it correctly. To rinse fill the entire water system with drinking water and empty it again sev- eral times. 12.3.
12 Care 12.4 Extractor hood X Prior to carrying out work on the device, turn off the power supply. Clean the grease filter of the range hood occasionally. How often cleaning is necessary depends on how often the range hood is used. Do not wait to clean the filter until the performance of the range hood has noticeably decreased. Cleaning grease filter: Remove the lower cover. Remove the filter. Wash the filter with warm water and some washing-up liquid.
12 Removing fingerprints: 12.5.2 Removing normal soiling: Care Clean the sink with a cleaning solution and a leather cleaning cloth. Rinse out the sink and dry it with household cloths. Plastic sink Z Do not use microfibre cloths for cleaning. Fine scratches could be created here. Z Do not use scouring milk/scouring powder or rough sponges. Clean the sink with a conventional cleaning solution or non-scouring house- hold cleaner.
12 Care 12.7 Winter care De-icing salt damages the underbody and the parts open to water spray. We recommend that you wash the vehicle more frequently during wintertime. Mechanical and surface treated parts and the underside are under particular strain, and should therefore be cleaned thoroughly. Z If there is any risk of frost, always run heater at a minimum of 15 °C. Set the cir- culation fan (if existing) to automatic mode.
12 Care 12.8 Lay-up 12.8.1 Temporary lay-up X If the vehicle has been stationary for a long period (approx. 10 months) have the braking and gas systems checked by an authorised specialist workshop. X Take into consideration that water is undrinkable after only a short time. X Animal damage to cables can lead to short circuits. Fire hazard! Animals (especially mice) can cause great damage to the interior of the vehicle. This is especially true if the animal remains undisturbed in a parked vehicle.
12 Care Activities Gas system Done Close regulator tap on the gas bottle Close all gas isolator taps Always remove gas bottles from the gas bottle compartment, even if they are empty Electrical system Fully charge living area battery Z Charge the battery for at least 20 hours before laying up. Spray the contacts on the thirteen-pin connector with contact spray Water system 12.8.2 Empty the entire water system. Leave the water taps on in central position.
12 Care Activities Complete vehicle Done Clean the awning area and store in a dry place Arrange the tarpaulins in such a way that the ventilation openings are not covered, or use porous tarpaulins 12.8.
12 Care 160 Caravan - 12-11 - EN
13 Maintenance Chapter overview 13Maintenance This chapter contains instructions about official inspections as well as inspection and maintenance work concerning the vehicle. The maintenance instructions address the following topics: z z z z stabiliser braking system alde hot-water heater replacing bulbs and fluorescent tubes At the end of the chapter you will find important instructions on how to obtain spare parts. 13.
13 Maintenance 13.4 Stabilisers Clean the stabiliser and the coupling head regularly. Use either thinners or white spirit. When lubricating the stabiliser ensure that no lubricant is on the friction pads. Fig. 169 Friction control of friction lining Friction control of friction lining Prerequisite: The stabiliser is connected. Close handwheel until ratcheting can be heard (turn to the right). z If the arrow on the pressure pad (Fig. 169,3) is in front of or on the marked sur- face (Fig.
13 Maintenance 13.5 Braking system AL-KO chassis Have maintenance work on the braking system carried out by a specialist workshop. Look up the following table for the inspection deadlines. 13.6 Model First inspection Braking system Brake lining AL-KO chassis After 1500 km or after 6 months Every 10000 to 15000 km or every 12 months Every 5000 km or every 12 months Alde hot-water heater Z Check the level of the heating fluid regularly on the compensator reservoir.
13 Maintenance Unscrew the screw cap (Fig. 171,1) at the compensator reservoir. Slowly remove the cover with circulating pump upwards. Check anti-freeze with an anti-freeze hydrometer. The frost protection content must be 40% or provide frost protection of up to -25 °C. Fill the water frost protection mixture slowly into the compensator reservoir. Z The optimum fluid level is reached when the fluid in the compensator reservoir is 1 cm above the "MIN" mark. 13.6.
13 Maintenance 1 Fig. 173 Lint filter air conditioning unit A lint filter (Fig. 173,1) for the air circulation suction system is located at the rear of the air conditioning unit. The lint filter must be cleaned at regular intervals, at least twice a year however, and replaced if necessary. Pull the lint filter out of the air conditioning unit, clean it or replace it if necessary. The condensation drain is under the floor of the vehicle.
13 13.8.1 Maintenance Ceiling lamp (cover with screws) 1 Fig. 174 Changing bulbs: 2 1 Ceiling lamp Undo the screws (Fig. 174,1) and carefully remove the glass cover (Fig. 174,2). Remove bulb. Put in a new bulb. Fasten the glass cover again. 13.8.2 Halogen spotlight (movable) Fig. 175 Changing bulbs: Halogen spotlight (movable) Loosen the fixing screws (Fig. 175,1). Carefully remove the lamp chalice (Fig. 175,2) from the holder. Remove halogen bulb.
13 13.8.3 Maintenance Halogen spotlight (with glass shade) 1 Fig. 176 Changing bulbs: 13.8.4 Halogen spotlight (with glass shade) Pull the halogen bulb (Fig. 176,1) forward out of the socket. Press the new halogen bulb into the fitting between the two spring tongues. Recessed halogen light (flat) Fig. 177 Recessed halogen light (flat) Fig. 178 Changing the halogen bulb The recessed halogen light (Fig. 177,1) is installed recessed.
13 13.8.5 Maintenance Recessed halogen light with housing Fig. 179 Recessed halogen light The recessed halogen light is installed flush in a housing (Fig. 179,1). Changing bulbs: Use a screwdriver to remove the inner cover ring (Fig. 179,3) from the housing. Remove the cover ring with the glass. Remove the halogen bulb (Fig. 179,2). Put in a new halogen bulb. Reassemble the lamp in the reverse order. 13.8.6 Surface-mounted halogen light (swiveling) 1 Fig.
13 13.8.7 Maintenance Indirect lighting 1 2 3 Fig. 181 Changing bulbs: Indirect lighting Remove the fixing screws (Fig. 181,1) of the cover (Fig. 181,2). Remove halogen bulb. Put in a new halogen bulb. Install the panel in the reverse order. 13.8.8 Light column Fig. 182 Changing bulbs: Light column Remove the trays (Fig. 182,2). Press the light glass (Fig. 182,1) lightly together and remove it. Remove halogen bulb. Put in a new halogen bulb.
13 13.8.10 Maintenance Wardrobe light 1 Fig. 183 Changing bulbs: 2 Wardrobe light Press the light covering (Fig. 183,1) lightly together and remove it. Remove halogen bulb. Put in a new halogen bulb. Reassemble the lamp in the reverse order. 13.9 Changing the battery of the wardrobe light with LED The wardrobe light has a button cell that supplies voltage to the LED. Z Use only button cells of the same type. Changing the batteries: Push the cover (Fig.
13 Maintenance For safety reasons, spare parts for pieces of equipment must correspond with manufacturer's instructions and be permitted by the manufacturer as a spare part. These spare parts may only be fitted by the manufacturer or an authorised specialist workshop. The authorised dealers and service centres are available for any spare parts requirement.
13 13.12 Maintenance Warning and information stickers There are warning and information stickers on and inside the vehicle. Warning and information stickers are for the sake of safety and must not be removed. Z Replacement stickers can be obtained from an authorised dealer or the service centre.
14 Wheels and tyres Chapter overview 14Wheels and tyres This chapter contains instructions regarding the tyres of the vehicle. The instructions address the following topics: z z z z tyre selection handling of tyres changing wheels spare wheel support At the end of the chapter there is a table you can use to find the correct tyre pressure for your vehicle. 14.1 General X Check the tyre pressure before a journey and at 2-week intervals.
14 Wheels and tyres Fig. 185 Tighten the wheel nuts or wheel bolts cross-wise Check regularly that the wheel nuts or wheel bolts are firmly seated. Re-tighten the wheel bolts of a changed wheel cross-wise after 50 km (30 miles) (Fig. 185). See Section 14.5.2 for tightening torque. When using new or newly painted rims, re-tighten the wheel nuts or wheel bolts once again after approx. 1000 to 5000 km (600 miles to 3000 miles).
14 Wheels and tyres 14.3 Tyre designations 215/70 R 15C 109/107 Q 14.4 Designation Explanation 215 Tyre width in mm 70 Height-to-width proportion in percent R Tyre design (R = radial) 15 Rim diameter in inches C Commercial (transporter) 109 Load index code for single tyres 107 Load index code for twin tyres Q Speed index (Q = 160 km/h) Handling of tyres Drive over kerbs at an obtuse angle. Otherwise the flanks of the tyres may get pinched.
14 Wheels and tyres X Persons may not lie under a vehicle that is jacked up. X If alloy wheels rims are in use and a steel spare wheel is mounted after a puncture: Do not drive any further than necessary (car dealer, car workshop, tyre dealer). Only drive at a suitable speed. The different wheels affect driving handling. Z Do not damage the thread of the thread bolts when changing the wheel. Z Tighten the wheel nuts or wheel bolts cross-wise (Fig. 185). Z When changing wheels (e.g.
14 Wheels and tyres Fig. 186 Preparing the connected caravan: Preparing the disconnected caravan: Securing support wheel Fig. 187 Securing vehicle Loosen the stabilising device in caravan couplings with stabilising devices. Oth- erwise the friction pads will be highly loaded. Pull the handbrake of the towing vehicle and go to first gear or reverse gear. Park the vehicle on as even and stable a surface as possible. Apply the handbrake.
14 Wheels and tyres Screw in the wheel bolts and slightly tighten them cross-wise. Crank down the vehicle jack and remove it. Using the wheel brace , tighten the wheel bolts evenly. The target value of the tightening torque of the wheel bolts is 90 Nm for steel wheel rims or 110 Nm for alloy wheel rims. 14.5.4 Changing the wheel at alloy wheel rims X The resting surfaces of the wheels on the break drums must be clean and free of burrs.
14 Wheels and tyres 14.7 Tyre pressure X Tyre pressure that is too low results in overheating of the tyre. Serious damage to the tyre can be the result. X Check the tyre pressure before a journey and at 2-week intervals. Wrong tyre pressure causes excessive wear and can lead to damage or even to tyre burst. You can lose control of the vehicle. X Use only valves that are approved for the specified tyre pressure. Z Only check the tyre pressure on cold tyres.
14 Wheels and tyres Tyres 195 R 14 C LI106 Maximum permissible gross weight mono axle (kg) Maximum permissible gross weight tandem axle (kg) Up to 1100 3.25 1200 3.25 1300 3.50 1400 3.50 1500 3.75 1600 2800 1700 195/70 R 14 LI91 195/70 R 14 XL LI95 1800 3500 4.50 Up to 1000 2000 2.50 1100 2200 2.70 Up to 1100 2000 2.90 1200 2200 3.10 3.40 Up to 1100 2200 1200 2500 3.80 1400 4.10 1500 4.50 1600 2800 4.80 1700 5.20 Up to 1100 3.25 1200 3.25 1300 3.
15 Troubleshooting Chapter overview 15Troubleshooting This chapter contains instructions about possible faults in your vehicle. The faults are listed with their possible causes and corresponding remedies.
15 Troubleshooting 15.3 Electrical system Z When the living area battery is changed, only use batteries of the same type. Z See Chapter 9 for changing the fuses. Fault Cause Remedy Road light system does no longer work correctly Bulb is defective Unscrew cover of the relevant light, replace bulb.
15 Troubleshooting Fault Cause Remedy No voltage from the living area battery (Power Pack SE) Living area battery is discharged Charge living area battery immediately Z Total discharge damages the battery. If the vehicle is to be laid up for a long period, fully charge the living area battery beforehand Discharging is caused by inactive appliances (see Chapter 9) Extractor hood does not work Air conditioning unit cannot be switched on or off 15.
15 Troubleshooting 15.5 Cooker 15.5.1 15.5.2 Gas cooker/gas oven Fault Cause Remedy Ignition fuse does not operate (flame does not burn after the control knobs are released) Heat-up time is too short Keep control knob pressed for approx. 15 to 20 seconds after ignition Ignition fuse is defective Contact customer service Flame extinguishes when being reduced to its minimum setting Thermocouple sensor is incorrectly set Set thermocouple sensor correctly (do not bend).
15 15.6.2 Troubleshooting Alde heater/boiler Z If a fault occurs in the system, the cause is shown on the display. Fault Cause Remedy Heater does not ignite with gas operation Lack of gas Open regulator tap and gas isolator tap Connect a full gas bottle Heater does not ignite Battery voltage too low Charge battery.
15 Electrical operation 15.6.4 15.
15 Troubleshooting Fault Cause Remedy Refrigerator does not switch on when operating in 12 V mode Jumbo flat fuse (40 A) in the starter battery is defective Replace jumbo flat fuse (40 A) in the starter battery Flat fuse (2 A) in the starter battery is defective Replace flat fuse (2 A) in the starter battery Disconnector relay in the transformer/rectifier is defective Contact customer service 12 V operating voltage too low Have the 12 V power supply checked by an authorised specialist workshop
15 Troubleshooting Error code 15.7.3 Cause Remedy z Check the gas supply z Repeat ignition 3 to 4 times z Contact customer service 9 The gas supply has been cut off.
15 15.7.4 Troubleshooting Fault Cause Remedy LEDs for display of the temperature range flash Temperature sensor defective Contact customer service LED " " and LEDs for display of the temperature range flash 240 V heater element defective Contact customer service LED " " and LEDs for display of the temperature range flash 12 V heater element defective Contact customer service Dometic 8 series with AES Z In the case of a fault the LED display fault will always light up " ".
15 Troubleshooting 15.8 Air conditioning unit Fault Cause Remedy Air conditioning unit does not cool No 230 V power supply Connect 230 V power supply Fuse is defective Check fuse and replace if necessary Temperature below 16 °C 15.
15 Troubleshooting Fault Cause Remedy Any change in the taste or odour of the water Tank filled with dirty water Clean water system mechanically and chemically; then disinfect and rinse copiously with drinking water Fuel filled into the water tank by mistake Clean water system mechanically and chemically; then disinfect and rinse copiously with drinking water.
15 15.
16 Special equipment 16.1 Weight details for special equipment 16Special equipment X The use of accessories, parts and fittings not supplied by Dethleffs may cause damage to the vehicle and jeopardise road safety. Even if an expert's report, a general type approval or a design certification exists, there is no guarantee for the proper quality of the product. X Every alteration of the original condition of the vehicle can alter road behav- iour and jeopardize road safety.
16 Special equipment Item designation Surplus weight (kg) Flat screen 6 Floor warming unit, electrical 9 External gas socket 1 Smooth plate 1 kg/m² Holder for flat screen 6 Trumatic 5002 heater 7 Heater cover (fireplace) 2 Heki skylight (Heki 2) 13 Insect screen door 3 Foam mattress 7-15 Air conditioning unit (Dometic) 40 Refrigerator with freezer compartment 30 Slatted frame, head section erectable 1 Microwave oven 15 Repair kit 1 Radio preparation 4-10 Satellite unit wit
17 Helpful notes Chapter overview 17Helpful notes This chapter contains helpful tips for your journey. The instructions address the following topics: z z z z z z Road assistance in European countries Traffic rules in European countries Gas supply in European countries Toll regulations in European countries Safe ways to spend the night during travel Camping in winter At the end of the chapter there is a checklist containing the most important equipment for your trip. 17.
17 Helpful notes Country German embassy Emergency services Police Auto club emergency call Breakdown service Finland 112 Helsinki (09) 45 85 80 112 ADAC Munich (00 49-89) 22 22 22 2) France 15/112 1) ADAC Lyon 08 25 80 08 22 Paris (01) 53 83 45 00 17/112 1) ADAC Lyon (00 33) 08 25 80 08 22 Greece 112/166 ADAC Athens (21) 09 11 79 11 Athens (21) 07 28 51 11 171 ELPA 1 04 00 Great Britain 112 London (0 20) 78 24 13 00 112 ADAC Munich (00 49-89) 22 22 22 Ireland 999/112 1) Dublin (0
17 Helpful notes Country German embassy Caravan - 12-11 - EN Emergency services Police Auto club emergency call Breakdown service Norway 113 Oslo (00 47) 23 27 54 00 112 ADAC Munich (00 49-89) 22 22 22 Austria 144/112 1) ADAC Vienna (01) 2 51 20 60 Vienna (01) 7 11 54 133/112 1) ÖAMTC 1 20 Poland 999/112 1) ADAC Posen (0 61) 8 31 98 88 Warsaw (0 22) 5 84 17 00 997/112 1) PZM (0 22) 5 32 84 33 Portugal 112 Lisbon (21) 8 81 02 10 112 ADAC Barcelona (00 34) 9 35 08 28 08 Romania 961
17 Helpful notes Country German embassy 1) 2) Emergency services Police Turkey 112 Ankara (03 12) 4 55 51 00 155/112 1) Hungary 104/112 1) Budapest (06) 14 88 35 00 107/112 1) Cyprus 112 Nicosia 22 45 11 45 112 Auto club emergency call Breakdown service ADAC Istanbul (02 12) 2 88 71 90 ADAC Istanbul (02 12) 2 88 71 90 ADAC Budapest (06) 13 45 17 17 MAK 1 88/(06) 1 13 45 17 44 1) ADAC Athens (00 30) 21 09 11 79 11 AA 02 22 31 31 31 In the mobile communication network Dialling code to Germany
17 Helpful notes Country In built-up areas Outside built-up areas Motorway 50 75 90 12) 40/60 80 80 Montenegro 50 80 – Netherlands 50 80/90 1) 13) 90 13) Norway 50 60 14)/80 60 14)/80 Austria 50 70/100 15) 80/100 15) Poland 50/60 16) 70/80 1) 80 Portugal 50 70/80 17) 100 18) Romania 19) 50 70/80 1) 90 Russia 60 70 90 20) Sweden 50 80 21) 80 21) Switzerland/Liechtenstein 50 80 22) 80 Serbia 50 80 80 Slovakian Republic 50 90 90 Slovenia 50 80 80 S
17 Helpful notes 16) From 11 p.m. to 5 a.m., max. 60 km/h According to traffic signs 18) Drivers who have had their driver's licence for less than one year must not drive faster than 90 km/h.
17 Helpful notes Country Sleeping on roads and fields Sleeping on privately owned lands Yes Yes Greece X United Kingdom X No X X Staying overnight in some places with local permission only. Staying overnight on the side of the road is not permitted Ireland X X Staying overnight on a beach or on the side of some streets and bridges is not permitted Italy X X Staying overnight at parking areas and rest areas is permitted. Observe the local limitations.
17 Helpful notes Sleeping on roads and fields Sleeping on privately owned lands Yes No Yes Switzerland X X Serbia X X Slovakian Republic X X Slovenia X X Country Spain X Turkey Hungary No One overnight stay at highway rest areas and in some cantons is tolerated.
17 Helpful notes Country Gas supply Provider Belgium Identical gas bottles Belgian Shell and Totalfina, Brussels; Primagaz, Tessenderlo; Gasbottling, Gent; Semnickgas, Geraardsbergen Exchanging and filling gas bottles possible Denmark Finland German 5 and 11 kg gas bottles are available for exchange at almost every campsite.
17 Helpful notes Country Gas supply Provider Croatia Gas bottles whose inspection lies less than 5 years back are filled in INA branches INA Info phone Adapter can be purchased at INA Netherlands Identical gas bottles Exchanging and filling gas bottles possible Norway German gas bottles cannot be filled Adapters for Norwegian gas bottles can be purchased from the AGA company Overview of provides from: AGA, Fax: 00 47/22 02 78 05 Statoil, Fax: 00 47/22 96 22 10 Deposit gas bottles available Aust
17 Helpful notes Country Gas supply Provider Turkey Sale of 2 and 12 kg gas bottles; connection possible with adapter Ipragaz company (www.ipragaz.com.tr/tupgazsize-en-yakin-bayi) Hungary Identical gas bottles Primagaz, Totalgaz, Shellgas, Mol Exchanging and filling gas bottles possible Norway Norwegian 11 kg gas bottles can be used with adapter Info phone Overview of provides from: AGA (www.aga.
17 Helpful notes 17.9 Tips for winter campers The following tips will help make your winter camping experience as agreeable as possible. z Reserve your parking place in good time. Good winter camping sites are often booked up early. z Do not start your trip without winter tyres. z Choose your parking place with care. Observe the ground beneath you. Snow and ice may melt.
17 17.10 Helpful notes Travel checklists The following checklists will help that nothing important is left at home although not everything on the checklists might be necessary. Z Do not leave checking of documents (e.g. vehicle papers and information) as well as checking the condition of the vehicle until just before commencing the trip. Planning and checking documents well in advance will save unnecessary trouble.
17 Vehicle/tools Outside Documents Helpful notes Object Object Gas bottle Radio Waste water container Fabric tape Screwdriver Adapter socket Watering can for fresh water Current-measuring instrument CEE adapter Cable reel Step Wire V-belt Wheel chocks Spare wheel Glue First-aid kit Spare lamps Universal pliers Vehicle jack Spare fuses Compressor Hazard warning triangle Replacement water pump Luster terminals Warning sign Hammer Loops Warning vest Flat wrench Tube adapter
Index 12 V fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 at the vehicle (Power Pack SE) . . . . . . . . . . . . . . . . . 96 For Thetford toilet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 On the power pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 On transformer/rectifier EBL109 . . . . . . . . . . . . . . . 97 12 V indicator lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 12 V main switch . . . . . . . .
Index Bulbs, changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 Ceiling lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166 Halogen spotlight . . . . . . . . . . . . . . . . . . . . . . .166, 167 Indirect lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 Recessed halogen light . . . . . . . . . . . . . . . . . .167, 168 Spotlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index D Danger of suffocation . . . . . . . . . . . . . . . . . . . . . . . . . 18, 52 DEKRA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161 Detaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Displays Filling level water tank . . . . . . . . . . . . . . . . . . . . 93, 94 Living area battery charging condition . . . . . . . . . 93 Disposal Household waste . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Sewage . .
Index Gas cooker Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184 Gas inspection certificate . . . . . . . . . . . . . . . . . . . . . . . . .161 Gas inspection sticker . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index Inner door, troubleshooting . . . . . . . . . . . . . . . . . . . . . .192 Insect screen, cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .152 Insect screen, conversion door Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Insect screen, Heki skylight Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Opening . . . . . . . . .
Index Overload protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Overrun brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 P Panel LT 109 (Power Pack SE) . . . . . . . . . . . . . . . . . . . . . . 92 Panel LT 222 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Panel see also displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Payload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index Sleeping conversion Bed expansion for playing area . . . . . . . . . . . . . . . . 75 Bench seating group and side seating group . . . 72 Rear seating group . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Round seating group . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170 Spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178 Spare wheel support . . . . . .
Index Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181 230 V connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .182 Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192 Boiler (Alde) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185 Boiler (Truma) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185 Braking system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index Water system Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 Disinfecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153 Drinking water filler neck . . . . . . . . . . . . . . . . . . . . .138 Emptying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143 Filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index 218 Caravan - 09-09 - EN
