Instruction manual Congratulations Instruction manual We congratulate you on your new caravan and would like to thank you for choosing a quality product from Dethleffs.
Instruction manual Caravan - 02-08 - DET-0030-07 EN
Contents 1 Guarantee . . . . . . . . . . . . . . . . . . . . . 7 1.1 1.2 1.3 1.4 Guarantee certificate. . . . . . . . . . . . . . . 7 Guarantee conditions . . . . . . . . . . . . . . 8 Inspection records. . . . . . . . . . . . . . . . . 9 Inspection plan for annual inspection . . . . . . . . . . . . . . . . . . . . . . 12 Inspection plan for water ingress test . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.5 2 Introduction . . . . . . . . . . . . . . . . . . 15 2.1 2.2 General . . . . .
Contents 7.12.2 10.2.3 10.2.4 10.2.5 10.2.6 7.12.6 Round seating group with rectangular table . . . . . . . . . . . . . . . . . 76 Round seating group with round table . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Widening the bed into a playing area (variant 1). . . . . . . . . . . . . . . . . . . 78 Widening the bed into a playing area (variant 2). . . . . . . . . . . . . . . . . . . 79 Seating group with two single beds . . . 80 8 Gas system . . . . . . . . . . . . . . . . . . . 81 8.
Contents 12 Care. . . . . . . . . . . . . . . . . . . . . . . . . 153 12.1 12.1.1 External care . . . . . . . . . . . . . . . . . . . Washing with a high-pressure cleaner . . . . . . . . . . . . . . . . . . . . . . . Washing the vehicle . . . . . . . . . . . . . Windows of acrylic glass . . . . . . . . . . Hot galvanized chassis . . . . . . . . . . . Underbody. . . . . . . . . . . . . . . . . . . . . Waste water tank . . . . . . . . . . . . . . . Filter for the external water connection. . . . . . . . .
Contents 6 Caravan - 02-08 - DET-0030-07 EN
Guarantee 1.1 Guarantee certificate 1 1Guarantee Vehicle data Model: Chassis manufacturer: Serial number: Initial registration: Purchased from company: Expiry of the guarantee period: Key number: Chassis number: Customer Address Surname, Christian name: Street, No.: Postal code, town: Dealer's stamp and signature We reserve the right to alter the construction, equipment and the scope of delivery. Special equipment is also listed that is not included in the standard scope of delivery.
1 Guarantee 1.2 Guarantee conditions 1. In addition to the legal guarantee and product warranty rights due to the customer, Dethleffs GmbH & Co. KG may also grant a guarantee of six years that the vehicles constructed by the company are sealed in such a manner that moisture cannot penetrate from the outside into the interior of the vehicle.
Guarantee 1.3 1 Inspection records Delivery Date: Signature and stamp of the Dethleffs dealer: 1st year Water ingress test Date: Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 1st year Water ingress test 1st year No defects found Found defects: Should it be determined during an inspection that additional work is necessary, then the carrying out of this work is dependent on the customer commissioning this to be done.
1 Guarantee 2nd year Water ingress test Date: Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 2nd year Water ingress test 2nd year No defects found Found defects: 3rd year Water ingress test Date: Signature and stamp of the Dethleffs dealer: Paste inspection stamp here.
Guarantee 4th year 1 Water ingress test Date: Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 4th year Water ingress test 4th year No defects found Found defects: 5th year Water ingress test Date: Signature and stamp of the Dethleffs dealer: Paste inspection stamp here.
1 Guarantee 1.4 Inspection plan for annual inspection Pos. 12 Component Activity Interval 1 Skylights Remove the inside frame of the skylights and tighten the screw connections of the securing clips 1.
Guarantee Pos. Component Activity Interval 19 Brake cable assembly Visual check Every two years 20 Chassis underbody Check bolts are firmly secured Every two years 21 Gas system Official gas inspection Every two years 1 We reserve the right to modify the inspection plan. 1.5 Caravan - 02-08 - DET-0030-07 EN Inspection plan for water ingress test Pos. Component Activity 1.1 Wheel housing Visual check 1.2 Rear wall floor plateau connection Visual check 1.2.
1 Guarantee Pos. Component Activity 3.3 Front wall floor plateau connection Spray with Dethleffs special weatherproof solution 3.4 Side wall floor plateau right connection Spray with Dethleffs special weatherproof solution 3.5 Side wall floor plateau left connection Spray with Dethleffs special weatherproof solution We reserve the right to modify the inspection plan.
Introduction 2 Please read this instruction manual completely before using the vehicle for the first time! 2Introduction Always keep this instruction manual in the vehicle. Also inform all other users of the safety regulations. The non-observance of this symbol can lead to personal injury. The non-observance of this symbol can lead to damage being caused to, or inside the vehicle. This symbol indicates recommendations or special aspects.
2 Introduction The reprinting, translation and copying, including extracts is not permitted without prior written authorisation from the manufacturer. 2.1 The vehicle comes without a wheelbrace and vehicle jack. We suggest you obtain a commercially available wheelbrace before you first use your caravan, in case of an emergency.
Introduction Caravan - 02-08 - DET-0030-07 EN 2 Empty waste bins as often as possible into the containers provided for this purpose. This helps to avoid unpleasant smells and an accumulation of rubbish on board. When parked, do not allow the engine of the towing vehicle to run more than necessary. When running idle, a cold engine releases more contaminants than usual. The running temperature of the engine is achieved more quickly whilst the vehicle is in motion.
2 18 Introduction Caravan - 02-08 - DET-0030-07 EN
Safety 3 Chapter overview 3Safety This chapter contains important safety instructions. The safety instructions are for the protection of persons and property. The instructions address the following topics: 3.1 3.1.1 Fire prevention Avoidance of fire risks 3.1.2 EN Keep flammable materials clear of heating and cooking appliances. Lights can get very hot.
3 Safety All windows and doors which meet the following requirements are considered as emergency exits: 3.2 General 3.3 The oxygen in the vehicle interior is used up by breathing or the use of the gas cooker or other appliances. That is why the oxygen needs to be replaced on a constant basis. For this purpose, forced ventilation options (e.g. skylights with forced ventilation or mushroom-shaped vents) are fitted to the vehicle.
Safety Caravan - 02-08 - DET-0030-07 EN 3 Before commencing the journey, turn the flat screen and the screen holder back to the basic position and slide them in until they lock into place. Close the TV cabinet. During the journey, no persons are to travel inside the caravan. When driving through underpasses, tunnels, etc. observe the overall height of the vehicle (refer to the technical data in the vehicle documents).
3 Safety 3.4 Towing 3.5 3.5.1 No persons are to be between the towing vehicle and the caravan during positioning for connecting and detaching. Gas system General instructions 22 Care is to be taken when connecting and detaching the caravan. Risk of accident and injury! Close all gas isolator taps and the regulator tap before commencing the journey and when leaving the vehicle. No source of combustion using gas (gas cooker, gas heater, gas boiler, etc.
Safety 3.5.2 EN Regularly inspect the gas tube fitted to the gas bottle connection for tightness. The gas tube must not have any tears and must not be porous. Have the gas tube replaced by an authorised specialist workshop no later than ten years after the manufacturing date. The operator of the gas system must see to it that the parts are replaced. Due to its function and construction, the gas bottle compartment is a space which is open to the exterior.
3 Safety 3.6 Electrical system 3.7 Prior to carrying out work on the electrical system, switch off all devices and lights, disconnect the batteries and disconnect the 240 V power cable from the mains. Only use original fuses with the stipulated values. Only replace defective fuses when the cause of the defect is known and has been remedied. Never bridge or repair fuses. Water system 24 Only allow qualified personnel to work on the electrical system.
Before the journey Chapter overview 4 4Before the journey This chapter contains important information which has to be noted before commencing your journey or carrying out any tasks before the journey.
4 Before the journey Connecting: 4.4 The tow ball is not to be lubricated when using a stabiliser. The friction pads are pressed against the coupling ball and thereby generate an antirolling moment. This anti-rolling effect is only guaranteed when the towing vehicle coupling head is free of lubricant and other residues. When lubricating the stabiliser ensure that no lubricant is on the friction pads.
Before the journey 4.4.1 WS 3000 D stabiliser Fig. 1 Connecting: 4 WS 3000 D stabiliser Pull the coupling handle (Fig. 1,1) upwards into position "Open" (Fig. 1,2). Stabiliser is open. Set down the open stabiliser on the caravan ball of the towing vehicle and release the coupling handle. The handle glides automatically back to its initial position (Fig. 1,3). In addition, push the coupling handle down with your hand (not with your foot). Closing and securing is carried out automatically.
4 Before the journey 4.5 Detaching Detaching: 4.6 Care is to be taken when connecting and detaching the caravan. Risk of accident and injury! In addition, observe the safety instructions with respect to connecting included in this instruction manual. Apply the caravan handbrake. Place the wheel chocks behind both of the wheels. Remove the connector plug of the caravan from the towing vehicle socket and insert it in the holder on the drawbar.
4 Before the journey 4.6.1 Terms Maximum permissible gross weight in a laden condition Technically speaking, the term "mass" has now replaced the term "weight". However, "weight" is still the term more frequent in common use. For better understanding, "mass" is therefore only used in the following sections for fixed formulations. All specifications according to EU norm DIN EN 1645-2. The maximum permissible gross weight in a laden condition is the weight that a vehicle may never exceed.
4 Before the journey Roof rail Spare wheel Awning Bike rack Satellite unit Microwave oven Hot water supply Chapter 16 lists the weights of the various items of special equipment; they may also be obtained from the manufacturer. Personal equipment Personal equipment includes all items in the vehicle that are not included in the additional equipment.
Before the journey 4 The payload (see section 4.6.1) is the difference in weight between Maximum permissible gross weight in a laden condition and Vehicle mass complete in a ready-to-drive condition.
4 Before the journey Fig. 3 Incorrectly loaded Loads stored apart from each other (Fig. 3) lead to inclination to skid. Roof loads impair the driving characteristics and move the centre of gravity upwards. This increases the inclination to skid. Fig. 4 Correctly loaded 4.6.4 Incorrect weight distribution Correct weight distribution Do not store heavy objects such as awnings, tin cans, etc. in the caravan but rather in the towing vehicle. Secure bicycles on the roof of the towing vehicle.
Before the journey 4 Example The towing vehicle may tow 1,200 kg. If the caravan has a maximum permissible gross weight of 1,200 kg and in fact weighs 900 kg, it can be loaded with another 300 kg. If however the caravan has a maximum permissible gross weight of 1,400 kg, it may only be loaded to a maximum of 1,200 kg. Nose weight The nose weight (Fig. 5,2) specifies how much weight the caravan drawbar can apply to the caravan coupling of the towing vehicle.
4 Before the journey 4.6.6 The maximum permissible roof load is 50 kg. The vehicle roof is not suitable for localised load. Before stepping on to the roof, extensively cover the area you will be treading on. Materials with a smooth or soft surface are suitable, for example, a thick polystyrene panel. Secure roof loads with tension belts. Do not use rubber expanders. Observe the overall height of the vehicle when the roof rack is loaded.
Before the journey 4 Lay the drive-on ramp on the ground (Fig. 7). Insert the edge guard (Fig. 7,1) in both holders in the drive-on ramp (Fig. 7,2). To push in the drive-on ramp, carry out the steps in reverse order. 4.7 PVC-floor covering 4.8 Rubber mats or long exposure to ketchup, carrot juice, ink, blood or lipstick can discolour the PVC floor covering. If possible, remove stains from the floor immediately.
4 Before the journey Fig. 9 Storing the flat screen: Holder with swivel arm Swing back the flat screen to its initial position and lock it into place. The flat screen is fastened to a swivel arm. Fig. 10 Storing the flat screen: 4.9 Holder with jointed arm Holder with swivel arm Swivel back the flat screen to the initial position, until both the release knobs (Fig. 10,1 and 2) lock in place. Road safety Check tyre pressure before a journey or every 2 weeks.
Before the journey No. Water system housing body Housing body, outside Housing body, inside Gas system Electrical system Checks Caravan - 02-08 - DET-0030-07 EN Checked 9 Mobile waste water tank stored away and secured in the gas bottle compartment 10 Water system emptied in case of risk of frost.
4 38 Before the journey Caravan - 02-08 - DET-0030-07 EN
During the journey Chapter overview 5 5During the journey This chapter contains instructions on how to drive the caravan. The instructions address the following topics: 5.1 driving speed brakes driving in reverse Driving with the caravan During the journey, no persons are to travel inside the caravan. The caravan constructions were designed for a maximum permissible speed of 100 km/h (60 mph). Therefore never drive faster than 100 km/h (60 mph).
5 During the journey Fig. 11 Driving in reverse: 40 Fig. 12 Steer to the left Drive up to the entrance until the rear of the caravan is roughly level with the entrance (Fig. 11). Steer the stationary towing vehicle and trailer to the left (Fig. 12). Reverse with caution. The caravan moves to the right. Fig. 13 Approach Approach Fig. 14 Steer to the right The angle between the vehicles must not be too narrow, otherwise the corners will bump against each other.
Pitching the caravan Chapter overview 6 6Pitching the caravan This chapter contains instructions on how to pitch the vehicle. The instructions address the following topics: 6.1 handbrake wheel chocks operation of the supports entrance step mobile waste water tank 240 V connection refrigerator Pitch the vehicle so that it is as horizontal as possible. Secure the vehicle to prevent it from rolling. Animals (especially mice) can cause great damage to the interior of the vehicle.
6 Pitching the caravan Fig. 16 Removal: 6.3 Wheel chock Swivel the retaining clip (Fig. 16,1) down. Remove the wheel chock (Fig. 16,2) from the holder. Corner steadies Do not use the fitted corner steadies as a vehicle jack. The corner steadies are only for stabilising the pitched caravan. The caravan wheels are not to be raised above the ground. When pitching the vehicle, ensure that the corner steadies are evenly loaded.
Pitching the caravan 6.4 Entrance step (free-standing) Make sure that the entrance step stands on secure and level ground. This will prevent the entrance step from toppling over. Do not step on the edges of the entrance step. Danger of slipping! Secure the entrance step to the ground, for example, with tent pegs. This way the entrance step cannot slip away. Fig. 18 6.5 6 Entrance step (free-standing) Place the entrance step (Fig. 18,1) in front of the entrance to the caravan.
6 44 Pitching the caravan Caravan - 02-08 - DET-0030-07 EN
Living Chapter overview 7 7Living This chapter contains instructions about living in the vehicle. The instructions address the following topics: 7.1 Doors 7.1.1 opening and closing the doors and external flaps heating the vehicle ventilation of the vehicle opening and closing the windows and blinds opening and closing the skylights converting tables positioning the television lamps extending the seating groups use of the beds Only drive with locked doors.
7 Living 7.1.2 Conversion door, outside (hinged handle) Fig. 22 Opening: Locking: 7.1.3 Insert the key in the locking cylinder (Fig. 22,1) and turn it in a clockwise direction until the door lock is unlatched. Return the key to the central position and remove it. Pull on the handle (Fig. 22,2). The door is open. Insert the key in the locking cylinder (Fig. 22,1) and turn it in an anticlockwise direction until the door lock is engaged. Return the key to the central position and remove it.
Living 7.1.4 7 Split conversion door The split conversion door can be adjusted with the catch levers so that only the upper part of the door can be opened. The lower part of the conversion door remains locked. Fig. 25 Opening the upper part of the door: 7.1.5 Catch lever on the lower part of the door Lock the lower part of the door. In order to carry this out turn catch lever (Fig. 25,1) a quarter turn in a clockwise direction. Open the upper part of the door.
7 Living 7.1.6 Blind on the conversion door The blind of the conversion door is located in the upper blind box. Fig. 27 Closing: Opening: 7.2 Blind Pull blind downwards by the handle (Fig. 27,2) and lock it into place. Pull blind downwards gently by the handle (Fig. 27,2) and push the unlocking bar (Fig. 27,1) outwards. The lock (Fig. 27,4) is released from the holder (Fig. 27,3). Use handle to return the blind slowly to its initial position.
Living Locking: 7.2.2 Insert the key into locking cylinder (Fig. 28,2) and turn until the flap lock is engaged. Return the key to the central position and remove it. Flap lock rear flap, inside Fig. 29 Opening: Locking: 7.2.3 Pull on the handle (Fig. 29,2). The flap lock is unlatched. The locking lever (Fig. 29,1) jumps out automatically. Press the locking lever (Fig. 29,1). During rain, water can penetrate the opened flap lock. Therefore close the lock handle. Fig.
7 Living 7.2.4 Press down lock handle with key inserted and turn key a quarter turn in a clockwise direction. The lock handle will stay bolted. Remove the key. Flap lock, rectangular Fig. 31 Opening: Closing: 7.2.5 Insert key into locking cylinder (Fig. 31,1) and turn a quarter turn. The lock handle (Fig. 31,2) snaps out. Remove the key. Turn the lock handle one quarter turn. The flap lock is open. Firmly close the external flap. Turn lock handle until it is horizontal.
Living Closing: 7.2.6 Close the flap for the toilet cassette and press it shut. Insert key into locking cylinder (Fig. 32,1) and turn a quarter turn. Remove the key. Cap for the fresh water filler neck Fig. 33 Opening: Closing: 7.2.7 Cap for the fresh water filler neck The fresh water filler neck is labelled with the word "WASSER" (water) (Fig. 33,1). Insert the key in the locking cylinder (Fig. 33,2) and turn it in an anticlockwise direction. Remove the cap.
7 Living 7.3 Heating 7.4 7.5 The oxygen in the vehicle interior is used up by breathing or the use of the gas cooker or other appliances. That is why the oxygen needs to be replaced on a constant basis. For this purpose, forced ventilation options (skylights with forced ventilation or mushroom-shaped vents) are fitted to the vehicle. Never cover or block forced ventilations with objects such as e.g. a winter mat. Keep forced ventilations clear of snow and leaves.
Living 7.5.1 When leaving the vehicle, always close the windows. In extreme weather conditions or if the temperature fluctuates strongly, a light condensation film can form on the double-glazed acrylic glass. The glass is designed in such a way that condensation can evaporate when the external temperature increases. There is no danger of the double-glazed acrylic glass being damaged by condensation.
7 Living To place the hinged window into the "continuous ventilation" position: Turn the catch lever (Fig. 37,3) a quarter turn towards the centre of the window. Lightly open the hinged window outwards. Return the catch lever to its initial position. The locking catch (Fig. 37,2) has to be moved into the recess of window catch (Fig. 37,1). During the journey, the hinged window may not be in "continuous ventilation" position.
Living Fig. 40 Continuous ventilation 7 Catch lever in the "continuous ventilation" position With the catch lever, the hinged window can be placed in two positions: "Continuous ventilation" (Fig. 40) Firmly closed (Fig. 38) To place the hinged window into the "continuous ventilation" position: Press the safety knob (Fig. 40,1) and keep it pressed. Turn the catch lever (Fig. 40,3) a quarter turn towards the centre of the window. Lightly open the hinged window outwards.
7 Living Fig. 41 Blind The blind is located in the upper blind box. Closing: Opening: Insect screen Pull blind at the handle (Fig. 41,2) downwards. If the blind is to be completely closed, it is suspended into the locking devices (Fig. 41,3) situated on both sides of the window frame. If the blind is completely closed: Press handle (Fig. 41,2) downwards and, at the same time, tilt it slightly inward.
Living 7.6.1 7 If the blind or the Roman shade is completely closed, exposure to direct sunlight can cause heat to accumulate between the blind/the Roman shade and the skylight. The skylight could be damaged. For that reason, close the blind/Roman shade only 2/3 of the way in direct sunlight. Open the skylight slightly or move it to ventilation position. Depending on the weather, close the skylights far enough to prevent moisture from entering. Do not climb on the skylights.
7 Living Closing: Blind Pull on the handle (Fig. 43,2). Fold insect screen (Fig. 43,1) downward. Using both handles (Fig. 44,1), pull down the skylight with force until the two snap latches lock into place. Swing insect screen upwards (Fig. 43,1) until it latches in place. To close and open the blind: Fig. 45 Closing: Opening: 7.6.2 Blind Pull the blind (Fig. 45,1) using the handle (Fig. 45,2) and hook the hooks (Fig. 45,3) in the opening (Fig. 45,4). Pull the hooks (Fig.
Living 7.6.3 7 Hinged skylight The hinged skylight may be opened on one side only. Three inclination angles and a ventilation position are available. An extension hook is included as standard equipment. Fig. 47 Opening: Closing: Locking in the ventilation position: Roman shade Hinged skylight, lock Fig. 48 Hinged skylight Turn the lever (Fig. 47,1 or Fig. 48,3) one quarter turn. Grip lever and push hinged skylight upwards. Grip lever and pull hinged skylight downwards.
7 Living 7.6.4 Heki skylight (mini and midi) Fig. 49 Safety knob on the Heki skylight Fig. 50 Heki skylight, guide The Heki skylight is opened on one side only. Opening: Closing: Press the safety knob (Fig. 49,2) and pull the bar (Fig. 49,1) down with both hands. Pull the bar (Fig. 50,1) in the guides (Fig. 50,2) to the rearmost position (Fig. 50,3). Use both hands to push the bar (Fig. 50,1) slightly upwards. Push the bar back into the guides.
Living Opening: Insect screen Closing: Opening: 7.6.5 7 Slowly push the Roman shade at the handle to its initial position. To close and open the insect screen: Pull the insect screen by the handle to the opposite handle of the Roman shade. Press the handle at the back of the insect screen. The latch is released. Use handle to return the insect screen slowly to its initial position. Heki skylight Fig. 53 Heki skylight, closed Fig.
7 Living Fig. 55 Ventilation position (variant 2): Open Heki skylight. Insert the bar (Fig. 55,3) into the holder (Fig. 55,1). Place the lever (Fig. 55,2) over the bar. Fig. 56 Roman shade Opening: Pull out Roman shade at the handle (Fig. 56,2) and release in the required position. The Roman shade will stay in that position. Slowly push the Roman shade at the handle to its initial position.
Living 7.6.6 7 Wind-up skylight Fig. 57 Wind-up skylight The wind-up skylight can be opened using the manual crank. Opening: Closing: Roman shade Opening: Closing: Opening: EN Check the locking mechanism. To do so, press your hand against the acrylic glass. Pull the handle of the Roman shade (Fig. 57,3) and release in the desired position. The Roman shade will stay in that position. Slowly push the Roman shade at the handle to its initial position.
7 Living 7.7 7.7.1 Tables Suspension table with fold-out leg Fig. 58 Bed foundation The table's fold-out leg enables it to be used as a bed foundation. Conversion to bed foundation: 7.7.2 Lift the front of the table-top (Fig. 58,1) by approx. 45°. Pull the lower part of the fold-out leg (Fig. 58,2) down and fold through 90°. Remove the table from its retainer. Insert the table into the lower retainer. Swivel table Lock the swivel table in position before commencing the journey. Fig.
Living Fig. 61 Conversion to bed foundation (swivel table with metal frame): 7.7.3 Swivel the table-top (Fig. 61,1) down with a circular movement until the handle locks into place. EN Fig. 63 Safety plate for swivel table with plastic frame Rotate handle (Fig. 62,2) into the horizontal position. Swivel the table-top (Fig. 62,1) downward in a circular movement. Insert safety plate (Fig. 63,1). The swivel mechanism is locked.
7 Living Removal: Fold the legs (Fig. 64,4) one after the other outwards, until the support clips (Fig. 64,2) engage in the hooks (Fig. 64,1) of the guides. Carefully turn round the folding table and place it between the benches. Carefully turn the folding table round and place it with the legs upwards onto the seat cushions. Pull the levers (Fig. 64,3) on both legs one after the other and fully retract the legs (Fig. 64,4). Place the folding table in the holder in the wardrobe and secure it.
Living 7.8 Television Flat screen in the TV cabinet Before commencing the journey, remove the television from the support and store it securely. Before commencing the journey, turn the flat screen and the screen holder back to the basic position and slide them in until they lock into place. Close the TV cabinet. Before commencing the journey, ensure that the antenna is in park position. Danger of accidents! The flat screen is attached to a console in the TV cabinet. Fig.
7 Living Flat screen with swivel arm The flat screen is fastened to a swivel arm. Fig. 69 Positioning the flat screen with swivel arm: 7.9 Pull up the release knobs (Fig. 69,1 and 3) to unlock the swivel arm. Swivel the flat screen with the holder (Fig. 69,2) into the desired position. Lamps Bulbs and light fittings can be extremely hot. Allow the light bulbs and lamp holders to cool down before touching them.
Living 7.10 Extending the central seating group Fig. 71 Extending: Retracting: 7.11 7.11.1 7 Support for bench seat extension Fold up the bench seat extension (Fig. 71,1). The support (Fig. 71,2) locks automatically into place. Lay the additional cushion onto the bench seat extension. Take the additional cushion from the bench seat extension and store it. Press the support (Fig. 71,2) against the resistance of the coil spring (Fig. 71,3) upwards in the direction of the arrow.
7 Living Fig. 72 Bunk bed, folding When the bunk bed is folded up, secure it with the retaining belt (Fig. 72,1). Depending on the model, the vehicle is fitted with a folding bunk bed. When the bunk bed is folded down, it can be used immediately without any additional conversion. The bunk beds can be folded up. The space under the bed can be used for storage. 7.11.3 Fixed bed (gas-pressure springs) Fig. 73 Fixed bed A storage compartment is underneath the bed.
Living Mechanical operation The bed can be adjusted to any height between both end positions. The socket for inserting the hand crank is located on the rear bed frame. If the rear bed is operated electrically, the rocker switch for raising and lowering the rear bed is located in the upper section of the right partition wall. The rear bed is raised or lowered with a hand crank. Fig. 74 Lifting the bed: Lowering the bed: Caravan - 02-08 - DET-0030-07 EN 7 Hand crank Fig.
7 Living Electric operation The rear bed is raised or lowered with a rocker switch. Fig. 76 Lifting the bed: Lowering the bed: 7.11.5 Fig. 77 Support bracket for the rear bed Press upper part of the rocker switch (Fig. 76,1) and keep it pressed until the bed is located somewhat over the desired position or at the end position. Bring the four support brackets (Fig. 77,2) to the desired height and insert the safety tabs in the holes (Fig. 77,3) on the four support rails (Fig. 77,1).
Living Fig. 78 Unfold: Caravan - 02-08 - DET-0030-07 EN Fig. 79 Swivel the folding bed Remove the table from the upper retainer and lay it aside. Remove the cushions from the seating group and lay them aside. Grip the folded sleeping area (Fig. 78,1) of the folding bed in the middle with one hand and tilt it slightly forwards. Grip the folded sleeping area with the other hand from below and press upwards.
7 Living Fig. 82 Folding together: 74 Folding bed, folding together Release the retaining straps of the safety net from the holders on the ceiling. Unhook the access ladder from the flush of the folding bed and store it. Remove the cushions from the lower bed and the table and lay them aside. Remove the mattress from the sleeping area and store it. Lay the safety net onto the sleeping area. Fold the back part of the split sleeping area forwards (Fig. 82).
Living 7.12 7.12.1 Converting seating groups for sleeping Bench seating group and side seating group Depending on the model, the seating group can be different in shape and position to the one shown here. 1 2 3 4 5 Fig. 83 Prior to conversion Fig. 84 After conversion Caravan - 02-08 - DET-0030-07 EN 7 Back cushion Seat cushion Table Bar Mounting rail Convert the table (Fig. 83,3) to a bed foundation (see section 7.7). Insert the bar (Fig. 83,4) or pull it to the centre.
7 Living 7.12.2 Round seating group with rectangular table Depending on the model, the seating group can be different in shape and position to the one shown here. 1 2 3 4 5 Fig. 85 Prior to conversion Fig. 86 During conversion Fig. 87 After conversion 76 Back cushion Seat cushion Table Back cushion Back cushion Convert the table (Fig. 85,3) to a bed foundation (see section 7.7). Pull the seat cushions (Fig. 86,2) into the centre. Insert the back cushions (Fig.
Living 7.12.3 Round seating group with round table 1 2 3 4 5 6 Fig. 88 Prior to conversion Fig. 89 During conversion Fig. 90 After conversion Caravan - 02-08 - DET-0030-07 EN 7 Back cushion Seat cushion Table Back cushion Back cushion Additional cushion Convert the table (Fig. 88,3) to a bed foundation (see section 7.7). Remove the back cushions (Fig. 89,1, 4 and 5). Pull the seat cushions (Fig. 90,2) into the centre. Insert the back cushions (Fig.
7 Living 7.12.4 Widening the bed into a playing area (variant 1) 1 2 3 4 5 6 7 8 9 Fig. 91 Prior to conversion Fig. 92 During conversion Fig. 93 After conversion 78 Back cushion Seat cushion Table Back cushion Back cushion Bedding box extension Additional board Additional cushion Bed Convert the table (Fig. 91,3) to a bed foundation (see section 7.7). Turn table one quarter turn in a clockwise direction and pull forwards to the right. Pull out the bedding box extension (Fig.
Living 7.12.5 Widening the bed into a playing area (variant 2) Fig. 94 Prior to conversion Fig. 95 During conversion Fig. 96 After conversion Caravan - 02-08 - DET-0030-07 EN 7 1 2 3 4 5 6 7 8 9 10 Back cushion Seat cushion Table Table leg Retainer Retainer Additional board Support legs Bed Additional cushion Swivel the table (Fig. 94,3) 45° upwards and remove it from the upper retainer (Fig. 94,5). Remove table leg (Fig. 94,4). Insert the bar (Fig.
7 Living 7.12.6 Seating group with two single beds 1 2 3 4 5 Fig. 97 Prior to conversion Fig. 98 During conversion Fig. 99 After conversion 80 Back cushion Seat cushion Folding table Bedside locker Slatted frame Fold up the folding table (Fig. 97,3) and store in the provided holder (see section 7.7.3). Completely pull out the slatted frame (Fig. 97,5). Place the back cushions (Fig. 98,1) on the slatted frames.
Gas system 8 Chapter overview 8Gas system This chapter contains instructions regarding the gas system of the vehicle. The instructions address the following topics: safety gas consumption changing the gas bottles gas isolator taps external gas connection automatic switching facility The operation of the gas operation appliances of the vehicle is described in chapter 10. 8.
8 Gas system 8.2 Regularly inspect the gas tube fitted to the gas bottle connection for tightness. The gas tube must not have any tears and must not be porous. Have the gas tube replaced by an authorised specialist workshop no later than ten years after the manufacturing date. The operator of the gas system must see to it that the parts are replaced. Due to its function and construction, the gas bottle compartment is a space which is open to the exterior.
Gas system 8.3 Connect gas pressure regulator complete with safety valve directly to bottle valve. The gas pressure regulator reduces the gas pressure in the gas bottle down to the operating pressure of the gas devices. If 2 gas bottles are used at the same time: Connect a gas pressure regulator fitted with an automatic switchover device. Information available at the Dethleffs service centre.
8 Gas system 8.5 Unscrew the gas pressure regulator (Fig. 100,3) along with the gas tube (Fig. 100,5) from the gas bottle with a suitable gas spanner. Release the fixing belts (Fig. 100,2) and take out the gas bottle. Place a filled gas bottle in the gas bottle compartment. Fix gas bottle in place with the fixing belts. Screw the gas pressure regulator with gas tube on the gas bottle and secure with a suitable gas spanner (Do not overtighten).
Gas system 8 Fig. 102 External gas connection, gas isolator tap closed The external gas connection (Fig. 102) is located at the front right. 8.7 Connect the external gas device to the connection point (Fig. 102,1). Open the gas isolator tap (Fig. 102,2). Duomatic switching facility Do not use the switching facility in closed spaces. Also read the manufacturer's instruction manual. The Duomatic is an automatic switching facility with a remote display for a twobottle gas system.
8 Gas system The manometer (Fig. 103,2) on the central regulator indicates the pressure in the gas bottle, not the filling level of the gas bottle. The manometer can be used to test the impermeability of the gas bottle. Only the electrical functions can be switched at the operating unit (Fig. 104). The regulator taps on the gas bottles (Fig. 103,1 and 4) must be opened manually. The central regulator provides a constant gas pressure, regardless of which gas bottle is being drawn upon.
Gas system Changing gas bottles: Caravan - 02-08 - DET-0030-07 EN 8 Always mount the regulator in such a way that the protective cap faces upwards. Close the regulator tap on the empty gas bottle. Unscrew the regulator of the gas bottle. Connect the full gas bottle to the regulator. Open the regulator tap on the gas bottle. Set the knob on the switching regulator with a half-turn, so that the newly replaced gas bottle will serve as a reserve bottle.
8 88 Gas system Caravan - 02-08 - DET-0030-07 EN
Electrical system Chapter overview 9 9Electrical system This chapter contains instructions regarding the electrical system of the caravan.
9 Electrical system 9.3 12 V power supply If you use the battery of the towing vehicle to provide power for the caravan, bear in mind that the battery capacity is restricted. If you place too great a burden on the battery, this may lead to starting difficulties. Always disconnect the electrical connection between the towing vehicle and the caravan before the caravan is connected to a 240 V power supply. In order to carry this out, disconnect the plug from towing vehicle socket.
Electrical system 9 The dryfill battery is maintenance-free. Maintenance-free means: It is not necessary to check the acid level. It is not necessary to lubricate the battery poles. It is not necessary to refill the distilled water. Even a maintenance-free dryfill battery must be charged regularly. When the vehicle is not connected to the 240 V power supply or the 240 V power supply is switched off, the living area battery supplies the living area with 12 V DC.
9 Electrical system Energy reserves 9.3.3 Off-load voltage (measured at the poles) Charging condition Higher than 12.80 V 100 % Approx. 12.55 V 75 % Approx. 12.32 V 50 % Approx. 12.18 V 25 % Lower than 12.00 V 0% The living area battery has a limited power supply only. That is why electrical appliances should not be operated over a long period of time if the vehicle is not connected to the 240 V power supply or the engine of the towing vehicle is switched off.
Electrical system 9 connected by a relay. This prevents the battery of the towing vehicle from being run down by electrical appliances in the living area. The starting capability of the towing vehicle is thus preserved. Charging with an external charger When charging the living area battery with an external charger, proceed as follows: 9.4 Disconnect the caravan electrically from the towing vehicle. Switch off 12 V main switch on the panel. The indicator lamp will go off.
9 Electrical system Transformer H Fig. 105 Power pack The 240 V automatic circuit breaker (Fig. 105,1), the overload protection (Fig. 105,2) and the main fuse (Fig. 105,3) are integrated in the power pack. The overload protection switches all 12 V appliances in the caravan off, if the power pack overheats. The power pack can overheat, if the ventilation apertures are covered by clothing or if many 12 V appliances are operated for a long time.
Electrical system Switching on overload protection (only type I): 9.5 9 When the overload protection triggers, allow the power pack to cool. Press upper part of the main switch (Fig. 106,4) first: Position "OFF". After about 60 seconds, switch the main switch back to position "ON". Transformer/rectifier EBL 109 (Power Pack SE) Do not cover the ventilation slots. Danger of overheating! Fig.
9 Electrical system When the transformer/rectifier is subject to a heavy load, the fitted charger module reduces the charging current. This protects the charger from overheating. The transformer/rectifier is subject to a heavy load when e.g. an empty living area battery is being charged, additional electrical appliances are turned on and the ambient temperatures are high. Position Depending on the model, the transformer/rectifier is situated either in the bench or in the bedding box. 9.5.
Electrical system 9.6.1 9 12 V main switch The 12 V main switch (Fig. 109,1) switches the 12 V power supply of the living area on and off. Switching on: Switching off: 9.6.2 Press the upper part of the rocker switch (Fig. 109,1): The 12 V living area power supply is switched on. The 12 V indicator lamp (Fig. 109,2) lights up in green. Press the lower part of the rocker switch (Fig. 109,1): The 12 V living area power supply is switched off. The 12 V indicator lamp (Fig. 109,2) goes off.
9 Electrical system 9.7 Panel LT 222 1 2 Rocker switch for water tank Water tank indicator lamp Fig. 110 Panel LT 222 Filling level of the tank Displays: 9.8 The filling level in the water tank can be read off on the panel (Fig. 110). Press rocker switch (Fig. 110,1): One of the indicator lamps (Fig. 110,2) is illuminated. 240 V power supply Only allow qualified personnel to work on the electrical system.
Electrical system 9.8.2 Power cable for external 240 V connection Power cable Connection possibilities Completely unwind the cable on cable drums to prevent overheating. Three-core (3 x 2.5 mm2) flexible rubber sheathed cable Maximum 25 m in length 1 plug with earth contact 1 socket with earth contact (plug-in devices according to EN 60309) In order to be prepared for all connection possibilities, Dethleffs recommends the following combinations: Fig.
9 Electrical system 1 2 Unbroken fuse element Broken fuse element Fig. 113 12 V fuse An intact 12 V fuse can be detected by the unbroken fuse element (Fig. 113,1). If the fuse element is broken (Fig. 113,2), change the fuse. Before changing fuses, take the function, value and colour of the relevant fuses from the following specifications. When changing fuses, only use flat fuses with the values shown below.
Electrical system Thetford toilet fuse (swivel toilet) 9 The fuse is located in the locker wall of the Thetford cassette. 1 Flat fuse 3 A/purple Fig. 114 Fuse for the Thetford toilet Changing: Thetford toilet fuse (fixed seat) Open the flap for the Thetford cassette on the outside of the vehicle. Pull out the Thetford cassette completely. Replace fuse (Fig. 114,1). The fuse is located in the locker wall of the Thetford cassette. 1 Flat fuse 3 A/purple Fig.
9 Electrical system 9.10 9.10.1 Connection to the towing vehicle Connection diagram 12N-12S connection Note the colours of the connecting cable of the socket which is fitted to the towing vehicle. This makes any new connection which may be necessary easier. Fig. 118 View of the Caravan plug Connection diagram 12N - black Connection diagram 12S - grey 102 Contact number DINspecification Function Cable colour Cross section of the wire 1 L Left direction indicator Yellow 1.
Electrical system 9.10.2 Towing vehicle installation Caravan - 02-08 - DET-0030-07 EN 9 The towing vehicle must be equipped with the corresponding cable cross sections and a relay for the power supply (controlled by the ignition).
9 104 Electrical system Caravan - 02-08 - DET-0030-07 EN
Appliances 10 Chapter overview 10Appliances This chapter contains instructions regarding the appliances of the vehicle. The instructions refer exclusively to the operation of the appliances. Further information about the appliances can be found in the instruction manuals for the appliances, included separately with the vehicle. The instructions address the following topics: 10.
10 Appliances 10.2 Heater Initial start-up 10.2.1 In winter, check that the waste gas vent on the vehicle roof is free of snow and ice before using the heater. Never let gas escape unburned due to danger of explosion. When filling the fuel tank of the towing vehicle, on ferries or in the garage, never run the heater in gas operation. Danger of explosion! Do not operate the heater in closed spaces (e.g. garages).
Appliances 10 Fig. 121 Hot-air heater control knob Switching on without automatic ignition: Switching on with automatic ignition: Switching off: Caravan - 02-08 - DET-0030-07 EN Open the regulator tap on the gas bottle and the gas isolator tap "Heater". Turn control knob on the heater to the required position and press it firmly. Press gas ignition button (at the control knob) several times in succession. Keep the control knob pressed until the flame burns.
10 Appliances Fig. 122 Removing heater cover Changing the battery on the automatic ignition: Fig. 123 Heater opened Make certain that the heater is switched off. Remove heater cover (Fig. 122,2). Pull the heater cover upwards and forwards, press up the retaining springs (Fig. 122,1) to the side and tip the cover forwards. Turn the cover (Fig. 123,1) to the side, so that the connecting cables for the hot-air fan as well as the ignition control lamp do not need to be disconnected.
Appliances 10.2.3 10 Circulation fan The circulation fan together with the hot-air heater ensures a better distribution of hot air throughout the caravan. Depending on the model either one or two circulation fans are installed in the vehicle. Fig. 125 Operating switch for circulation fan (240 V) Switching circulation fan (240 V) on: Switching circulation fan (240 V) off: Turn the rotary switch (Fig. 125,1) to " ". Turn the knob (Fig. 125,2) to the required position of the circulation fan.
10 Appliances Fig. 127 Circulation fan Fig. 128 Circulation fan, adjustment flap in central position The hot air flow can be adjusted as required with the operating lever (Fig. 127,1) on the back of the circulation fan. Factory setting is the central position. In the central position the warm air is distributed evenly to each warm air outlet. The operating lever (Fig. 128,1) for the adjustment flap is located under the base flap in the wardrobe. Setting the hot air distribution: 10.2.
Appliances 10.2.5 10 See installation instructions of the separate instruction manual for the Airmix comfort package. Alde hot-water heater Never run hot-water heater without heating fluid. Observe notes in chapter 13. Never drill holes in the floor. This might damage the hot-water pipes. Do not use the space above and behind the heater as a storage compartment. The circulating pump must always be turned on when the hot-water heater is in operation.
10 Appliances Pos. in Fig. 130 Button 4 Starting operation and selecting a symbol 3 +/On Activating the selected menu or increasing the displayed value 5 -/Off Deactivating the selected menu or decreasing the displayed value Ending operation 2 6 LCD display Function Store Reset Resetting the system to home position or saving the set time The LCD displays are divided into four sections: Upper menu line (Fig. 130,10) Status line (Fig. 130,9) Information line (Fig.
Appliances Pos. in Fig. 131 Status line Circulating pump is activated 8 240 V power supply is connected 20 Internal temperature display 9 External temperature display (only when an external temperature sensor is installed) Day, hour and minute display when setting the time e.g. Hour Details about temperatures, times and operating states or even error messages are displayed as text in the Information line (Fig. 131,19). Pos. in Fig.
10 Appliances Selecting gas and 240 V electrical operation: Select gas operation and 240 V electrical operation on the operating unit. If gas and 240 V electrical operation is selected and if the vehicle is connected to the 240 V power supply, then the hot-water heater at first only operates in 240 V electric operation. Only if the heat output is insufficient does the gas operation also automatically switch on.
Appliances 240 V circulating pump 10 Depending on the equipment, the hot-water heater has an additional 240 V circulating pump. If the vehicle is connected to the 240 V power supply, then it is possible to switch to the higher output of the 240 V circulating pump. The switch for switching between the 12 V circulating pump and the 240 V circulating pump is located on the hot-water heater operating unit. Selecting the circulating pump: 10.2.6 Press the " " button (Fig.
10 Appliances 10.2.7 Warming unit for waste water pipes Always only press the test button briefly. The warming unit only functions when the vehicle is connected to a 240 V power supply. In order to prevent waste water pipes freezing up, the waste water pipes can be electrically warmed. When the warming unit is turned on, the temperature of the waste water pipes is monitored by temperature sensors.
Appliances 10.2.8 10 Electrical floor warming unit On models with electrical floor warming unit, never drill holes in the floor or screw in any screws. Careful with sharp objects. There is danger of a power cut or a short circuit due to damage to a heater wire. Do not cover the regulator. Danger of overheating! The electrical floor warming unit only operates if the vehicle is connected to the 240 V power supply.
10 Appliances 10.2.9 Floor warming unit/warming unit for waste water tank For models with a floor warming unit and a warming unit for the waste water tank, never drill holes in the floor or screw in any screws. Danger of damage to a heating line and water leaking into the floor. The floor warming unit and waste water tank warming unit only operate when the hot-water heater is switched on.
Appliances Fig.
10 Appliances Air current Adjusting air current: Status LED Signification Off Air conditioning unit off Orange Air conditioning unit ready to operate Green Air conditioning unit in operation Red (continuous) No 240 V power connection Red (flashes once intermittently) Fault in the interior temperature gauge Red (flashes twice intermittently) Fault in the exterior temperature gauge The air current can be directed in different directions.
Appliances 10.4.2 10 Truma boiler Remove cap from waste gas vent before using the Truma boiler. The boiler is gas operated. The electrical control of the boiler is provided with power by the living area battery. 1 2 3 4 5 Temperature control knob Red indicator lamp "Fault" Rotary switch Off On Fig. 139 Operating unit for Truma boiler Switching on: Remove cap from waste gas vent. Open the regulator tap on the gas bottle and the gas isolator tap "Boiler". Switch the 12 V power supply on.
10 Appliances Emptying the boiler: 10.4.3 Switching the boiler on/ off Filling/emptying the boiler Set all the water taps to "Hot" and open them. The water pump is turned on. The warm water pipes are filled with water. Keep the taps open until the water flowing out of the taps has no bubbles in it. This is the only way to ensure that the boiler is full of water. Close all water taps. Turn the rotary switch (Fig. 139,3) to " ". Turn knob (Fig.
Appliances 10.4.4 10 Open drain cocks (Fig. 141). To do this, set the rocking levers (Fig. 141,1) in a vertical position. The boiler is drained to the outside using the drain cocks. Check whether the water has been drained completely from the boiler (approx. 12.5 litres). Further information can be obtained from the separate instruction manual "Alde Compact". Reich boiler Fig. 142 Reich boiler The boiler is operated with 240 V. The boiler heats about 5 l of water.
10 Appliances 10.4.5 Further information can be obtained in the manufacturer's instruction manual. Hot water source If you want to empty the hot water source: Empty the water tank completely before opening the drain cocks of the hot water source. Do not fit a check valve in the cold water pipe between the hot water source and the water pump. Use a pressure reducer when connecting to a central water supply or with strong pumps. The hot water source is designed only for pressures of up to 1.
Appliances 10 Fig. 144 Drain cock for hot water source Filling the hot water source with water: Emptying the hot water source: 10.5 EN Switch off the operating switch (Fig. 143). Indicator lamp (Fig. 143,1) in the switch is not on. Close drain cock. To do this, turn cap (Fig. 144,1) in a clockwise direction. Set all the water taps to "Hot" and open them. The water pump is turned on. The warm water pipes are filled with water.
10 Appliances 10.5.1 Gas cooker During activation and operation of the gas cooker, no flammable objects or highly inflammable objects such as dishcloths, napkins etc. must be near the gas cooker. Fire hazard! The process of ignition must be visible from above and must not be covered by cooking pans placed on the cooker. Depending on the model, the gas cooker lid is held closed by a spring.
Appliances Switching off: 10.5.2 10 Turn the control knob to the 0-position. The flame fades. Close the gas isolator tap "Cooker" and the regulator tap on the gas bottle. Gas oven Keep the ventilation openings on the gas oven open at all times. There must be no flammable objects near the gas oven when it is being lit. The oven flap must remain open when it is being lit. If ignition has not taken place, repeat the entire procedure.
10 Appliances 10.5.3 Gas cooker Gas cooker with gas oven and gas grill During activation and operation of the gas cooker, no flammable objects or highly inflammable objects such as dishcloths, napkins etc. must be near the gas cooker. Fire hazard! The process of ignition must be visible from above and must not be covered by cooking pans placed on the cooker. Depending on the model, the gas cooker lid is held closed by a spring.
Appliances Gas oven and gas grill Switching on the gas grill: Switching on the gas oven: Switching off the gas oven and gas grill: 10.5.4 EN Always keep ventilation apertures open. There must be no flammable objects near the gas oven or the gas grill when it is being lit. The flap must remain open when it is being lit. If ignition has not taken place, repeat the entire procedure.
10 Appliances Never leave the microwave oven unattended when it is in operation. If there is smoke, keep the microwave oven closed, switch it off and interrupt the power supply. Operate the microwave oven only with the rotary plate and the rotary cross in place. Use only crockery suitable for microwave use. The microwave oven only functions with correct 240 V power supply. In the case of fluctuations of the voltage or of voltage below 230 V, the microwave oven switches itself off completely.
Appliances Fig. 150 Extractor hood with lights 10 Fig. 151 Extractor hood without lights Press switch (Fig. 150,2 or Fig. 151,1) to switch the extractor hood on and off. The switches (Fig. 150,1 and 3) are used to turn the cooker lamp in the extractor hood on and off. Depending on the model, the cooker lamp can be operated with 240 V with switch (Fig. 150,1). The cooker lamp is operated with 12 V with switch (Fig. 150,3). 10.
10 Appliances Thetford Fig. 154 Refrigerator ventilation grill (Thetford) Removal: 10.6.2 Operating modes Move the locking device (Fig. 154,1) to the middle. Remove refrigerator ventilation grill. Operation (Dometic 7 series) The refrigerator has 2 operating modes: Gas operation Electrical operation (240 V AC or 12 V DC) The operating mode is set with the operating controls on the refrigerator panel. Gas operation Select only one energy source.
Appliances Switching on: Switching off: Electrical operation 10 Open the regulator tap on the gas bottle and the gas isolator tap "Refrigerator". Set energy selector switch (Fig. 155,1) to "GAS". Press the control knob (Fig. 155,2), turn it to the highest level and hold it down. Wait until gas gets into the burner. Press the gas ignition button (Fig. 155,3) repeatedly until the flame appears in the inspection glass (bottom left in the refrigerator). Keep the control knob (Fig.
10 Appliances 10.6.3 Operating modes Operation (Dometic 7 series with manual ignition and frame heater) The refrigerator has 2 operating modes: Gas operation Electrical operation (240 V AC or 12 V DC) The operating mode is set with the operating controls on the refrigerator panel. Gas operation Select only one energy source. Even when the 12 V power supply is switched off, a small electrical power flows which puts an extra load on the living area battery.
Appliances Switching off: Electrical operation 10 Set energy selector switch to " ". Refrigerator is switched off. Close the gas isolator tap "Refrigerator" and the regulator tap on the gas bottle. Close the gas isolator tap "Refrigerator" when the refrigerator is operated electrically.
10 Appliances 10.6.4 Operating modes Operation (Dometic 7 series with AES) The refrigerator is equipped with an automatic system to select the type of power (AES). The AES automatically selects the optimal energy source and regulates the refrigerator operation. Manual intervention to select the type of power is possible but not required. The AES selects from the following types of power: Solar installation 12 V 240 V AC 12 V DC Gas Choosing the available energy source highest on the list.
Appliances Change-over between energy sources 10 Open flames are prohibited at petrol stations. If the stop takes longer than 15 minutes, the refrigerator has to be turned off at the energy selector switch. When changing over between the different power sources there are forced delays built in the AES. This means, that after a change-over to a new energy source the refrigerator can not be operated immediately.
10 Appliances Gas operation Select only one energy source. Even when the 12 V power supply is switched off, a small electrical power flows which puts an extra load on the living area battery. Always switch off the refrigerator for a temporary lay-up. Never let gas escape unburned due to danger of explosion. 1 2 3 Energy selector switch Flame indicator Control knob for setting the temperature Fig.
Appliances Switching the 240 V operation on: Switching the 240 V operation off: Switching the 12 V operation on: Switching the 12 V operation off: Set energy selector switch (Fig. 158,1) to 240 V operation " 10 ". Use the control knob (Fig. 158,3) to adjust the refrigerating temperature. Set energy selector switch to " ". Refrigerator is switched off. Set energy selector switch (Fig. 158,1) to 12 V operation " Set energy selector switch to " ". Refrigerator is switched off. ".
10 Appliances Dometic 7 series Fig. 159 Locking of the refrigerator door (Dometic 7 series) Opening: Closing: Locking in the ventilation position: Push the lock (Fig. 159,1) to the left " Fig. 160 Refrigerator door in ventilation position (Dometic 7 series) ". Use recessed grip to open refrigerator door. Fully close the refrigerator door. Push the lock (Fig. 159,1) completely to the right " ". Slightly open refrigerator door. Push the lock completely to the right.
Appliances Locking in the ventilation position: 10 Slightly open refrigerator door/freezer compartment door. Push the lock completely to the right. The door latch (Fig. 162,1) keeps the refrigerator door/freezer compartment door in a fixed position. The refrigerator door/freezer compartment door will then stay slightly open (Fig. 162). Thetford Fig.
10 142 Appliances Caravan - 02-08 - DET-0030-07 EN
Sanitary fittings Chapter overview 11 11Sanitary fittings This chapter contains instructions regarding the sanitary fittings of the vehicle. The instructions address the following topics: 11.1 the external water connection waste water tank complete water system toilet compartment toilet Water supply, general Fill the water tank with fresh water only. Water left standing in the water tank or in the water pipes becomes undrinkable after a short period.
11 Sanitary fittings 11.3 Insert the plug for the power supply on the supply point. Waste water tank 11.3.1 Insert the hose of a water pump with the coupling on the connection coupling. Before commencing the journey, empty the waste water tank. If there is any risk of frost, empty the waste water tank.
Sanitary fittings 11.3.2 11 Waste water tank, permanently installed Fig. 167 Waste water drain neck and drain cock The waste water tank is located in the caravan and is permanently mounted. The waste water tank collects waste water. Emptying: 11.3.3 Place a suitable container under the waste water drain neck (Fig. 167,2) or position the vehicle with the drain neck over a specially designated disposal point. Open the drain cock (Fig. 167,1). The waste water will run out. Close drain cock.
11 Sanitary fittings 11.3.4 Odour seal Fig. 169 Odour seal In order to prevent odours occurring in the waste water system, the vehicle depending on the model - has been equipped with odour seals (Fig. 169,1). The odour seals are installed in the waste water pipes. Clean the odour seals every two years at the latest. To do so, unscrew and remove the bottom cover (Fig. 169,2). 11.
Sanitary fittings 11.5 11 Emptying the water system If the vehicle is not used for several days or if it is not heated when there is a risk of frost, empty the entire water system. Leave the water taps on in central position. Leave all drain cocks open. Frost damage to appliances, frost damage to the vehicle and deposits in water-carrying components can be avoided in this way. Take note of the environmental tip in this chapter. To empty and ventilate the water system, proceed as follows.
11 Sanitary fittings For example, the light switch (Fig. 170,1) of the toilet compartment is located under the bathroom cabinet. 11.7 Close the shower curtain completely when showering, so that no water is able to enter the area between the wash room wall and the shower tray. After taking a shower, rinse soap residue from the shower tray, otherwise cracks can appear in the shower tray over time. After using the shower, wipe it dry to prevent moisture from collecting.
Sanitary fittings Fig. 171 Thetford toilet bowl, swivelling Flushing: 11 Fig. 172 Flush button/indicator lamp Thetford toilet Before flushing open the sliding trap of the Thetford toilet. To do this, push the slide lever (Fig. 171,1) in an anticlockwise direction. For flushing, press the blue flush button (Fig. 172,1). After flushing close the sliding trap. To do this push the slide lever in a clockwise direction. The indicator lamp (Fig.
11 Sanitary fittings Fill with fresh water until the fluid level reaches the top edge. This corresponds to approx. 15 l. Close the screw cap. Swivel the fresh water filler neck inwards. Close the flap for the Thetford cassette. Fig. 175 Operating unit Thetford toilet Flushing: Before flushing open the sliding trap of the Thetford toilet. To do this, turn the slide lever (Fig. 175,1) in an anticlockwise direction. For flushing, press the blue flush button (Fig. 175,3).
Sanitary fittings Fig. 176 Flap for the Thetford cassette 11.7.4 11 Fig. 177 Thetford cassette Open the flap for the cassette on the outside of the vehicle. Insert the key into the locking cylinder of the push-button lock (Fig. 176,1) and turn a quarter turn. Remove the key. Press both push-button locks (Fig. 176,2) simultaneously with your thumb and open the flap for the cassette. Pull the retaining clip (Fig. 177,1) upwards and pull out the cassette (Fig. 177,2). Emptying the cassette Fig.
11 152 Sanitary fittings Caravan - 02-08 - DET-0030-07 EN
Care 12 Chapter overview 12Care This chapter contains instructions regarding the care of the vehicle. The instructions address the following topics: exterior of the vehicle filter of the external water connection interior extractor hood air conditioning unit winter operation At the end of the chapter there is a checklist of measures you must carry out if you are not going to use the vehicle for an extended period of time. The checklist address the following topics: 12.1 12.1.
12 Care 12.1.3 Add-on parts made of glass-fibre reinforced plastic (GRP) require a regular follow-up treatment with a polisher. This way these parts will not turn yellow and the sealing of the surface remains intact. Treat rubber seals of doors and storage flaps with talc. Treat locking cylinder of doors and storage flaps with graphite dust. Windows of acrylic glass Acrylic glass windows are delicate and require very careful handling. 12.1.
Care 12.1.6 12 Only use products approved by the manufacturer. Our authorised dealers and service centres will be happy to advise you. Waste water tank Clean the waste water tank after every use of the vehicle. Cleaning: 12.2 Open the cleaning opening on the waste water tank and the drain cock. Thoroughly rinse out the waste water tank with fresh water. Filter for the external water connection Fig.
12 Care 12.4 For information about the use of maintenance products, our representatives and service centres will be glad to advise. Surface and knobs of furniture, lamps and synthetic parts in the toilet and living area should be cleaned with water and a wool cloth. A mild cleanser may be added to the water. If required, use furniture polish for the painted surfaces.
Care 12.5 12 Dometic air conditioning unit Fig. 180 Air conditioning unit (Dometic) A lint filter and an activated carbon filter are each located in the lower part of the air conditioning system ceiling unit (Fig. 180,2) behind the ventilation grills (Fig. 180,1 and 3). The lint filters must be cleaned at regular intervals and replaced if necessary. The manufacturer recommends replacing the activated carbon filter yearly.
12 Care 12.6.2 Winter operation During winter operation, condensation develops when the vehicle is occupied under low-temperature conditions. To ensure good interior air quality and avoid vehicle damage from condensation, sufficient ventilation is essential. 12.6.3 12.7.1 When heating the vehicle, the heater should be at the highest setting and roof storage cabinets, curtains and blinds should be opened. This ensures optimal ventilation.
Care 12 Before laying up the vehicle, go through the following checklist: Activities Chassis Done Lubricate the moving parts of the caravan coupling Do not lubricate the friction pads on the Winterhoff (WS) or AL-KO (AKS) stabiliser! Jack up caravan with suitable support so that the wheels do not bear any load, or move caravan every four weeks.
12 Care 12.7.
Care 12.7.
12 162 Care Caravan - 02-08 - DET-0030-07 EN
Maintenance Chapter overview 13 13Maintenance This chapter contains instructions about inspection and maintenance work concerning the vehicle. The maintenance instructions address the following topics: stabiliser braking system Alde hot-water heater replacing bulbs and fluorescent tubes At the end of the chapter you will find important instructions on how to obtain spare parts. 13.1 Inspection work Like any technical appliance, the vehicle must be inspected at regular intervals.
13 Maintenance 13.3.2 AKS 3004 Fig. 181 Stabilising handle Checking the stabilising device (on the side of the friction pads) Prerequisite: Connection to AKS 3004, ball diameter 50 mm 13.3.3 Open the stabilising handle (Fig. 181,1). Close the stabilising handle until a resistance can be felt (the friction pads lie on the ball, they have not been tightened yet). If the arrow on the pressure pad (Fig. 182,3) is in front of or on the marked surface (Fig.
Maintenance 13.4 13 When the pin (Fig. 184,2) is in the longitudinal hole at the marking with the "+", the friction pads are still in good condition. When the pin is at both centre markings, the friction pads are slightly worn. When the pin is at the marking with the "–", the friction pads are worn and must be replaced. It is not possible to reset the friction pads. Braking system BPW/AL-KO chassis Have maintenance work on the braking system carried out by a specialist workshop.
13 Maintenance 13.5.1 Checking the fluid level Fig. 185 Compensator reservoir hotwater heater 13.5.2 Check if the fluid level is between the marks "MIN" (Fig. 185,3) and "MAX" (Fig. 185,2) on the compensator reservoir (Fig. 185). Topping up heating fluid 13.5.3 Switch off the hot-water heater and allow it to cool down. Position the vehicle horizontally. This prevents the formation of bubbles. Switch off the hot-water heater and allow it to cool down.
Maintenance 13.6 Close bleeding valve. Repeat this procedure at all bleeding valves. Check to see if the hot-water heater warms up. Replacing bulbs and fluorescent tubes 13.6.1 13 Bulbs and light fittings can be extremely hot. Therefore, allow lights to cool down before changing bulbs. Shut off the power supply on the safety cut-out in the 240 V fuse box before changing bulbs. Store bulbs in a safe place inaccessible to children.
13 Maintenance 13.6.2 Halogen spotlight (movable) Fig. 188 Halogen spotlight (movable) Changing bulbs: 13.6.3 Loosen the fixing screws (Fig. 188,1). Carefully remove the lamp chalice (Fig. 188,2) from the holder. Remove halogen bulb. Put in a new halogen bulb. Reassemble the lamp in the reverse order. Halogen spotlight (with glass shade) Fig. 189 Halogen spotlight (with glass shade) Changing bulbs: 13.6.4 Pull the halogen bulb (Fig. 189,1) forward out of the socket.
Maintenance 13.6.5 13 Change the fluorescent tube. Reassemble the lamp in the reverse order. Recessed halogen light (flat) Fig. 191 Recessed halogen light (flat) Fig. 192 Changing the halogen bulb The recessed halogen light (Fig. 191,1) is embedded in the panel or the canopy. Changing bulbs: 13.6.6 Use a screwdriver to remove the inner cover ring (Fig. 192,1) from the housing. Use a screwdriver to remove the cover ring with the glass (Fig.
13 Maintenance 13.6.7 Surface-mounted halogen light (swivelling) Fig. 194 Surface-mounted halogen light (swivelling) Changing bulbs: 13.6.8 Use a suitable tool (e.g. a screwdriver) to lever out and remove the cover (Fig. 194,1). Remove halogen bulb. Put in a new halogen bulb. Reassemble the lamp in the reverse order. Indirect lights Fig. 195 Indirect lights Changing bulbs: 170 Remove the fixing screws (Fig. 195,1) on the panel (Fig. 195,2). Remove halogen bulb.
Maintenance 13.6.9 13 Light column Fig. 196 Light column Changing bulbs: 13.7 Remove trays (Fig. 196,2). Compress the lamp glass (Fig. 196,1) lightly and remove. Remove halogen bulb. Put in a new halogen bulb. Reassemble the lamp in the reverse order. Changing the battery of the wardrobe light with LED The wardrobe light has a button cell that supplies voltage to the LED. Use only button cells of the same type. Fig.
13 Maintenance 13.8 Spare parts Every alteration of the original condition of the vehicle can alter road behaviour and jeopardize road safety. The special equipment and original spare parts recommended by Dethleffs have been specially developed and supplied for your vehicle. These products are available at your Dethleffs dealer. The Dethleffs dealer is informed about admissible technical details and carries out the required work correctly.
Maintenance 13 Do not remove the vehicle identification plate. The vehicle identification plate: Identifies the vehicle Helps with the procurement of spare parts Together with the vehicle documents identifies the vehicle owner Always include the vehicle identification number with all inquiries for the customer service office. 13.10 Warning and information stickers There are warning and information stickers on and inside the vehicle.
13 174 Maintenance Caravan - 02-08 - DET-0030-07 EN
Wheels and tyres Chapter overview 14 14Wheels and tyres This chapter contains instructions regarding the tyres of the vehicle. The instructions address the following topics: tyre selection handling of tyres changing wheels spare wheel support At the end of the chapter there is a table you can use to find the correct tyre pressure for your vehicle. 14.1 General Check tyre pressure before a journey or every 2 weeks.
14 Wheels and tyres Fig. 199 Tighten the wheel nuts or wheel bolts cross-wise 14.2 Check regularly that the wheel nuts or wheel bolts are firmly seated. Retighten the wheel nuts or wheel bolts of a changed wheel cross-wise (Fig. 199) after 50 km (30 miles). When using new or newly painted rims, re-tighten the wheel nuts or wheel bolts once again after approx. 1,000 to 5,000 km (600 miles to 3,000 miles).
Wheels and tyres 14.3 215/70 R 15C 109/107 Q 14.4 Tyre specifications Description Explanation 215 Tyre width in mm 70 Height-to-width proportion in percent R Tyre design (R = radial) 15 Rim diameter in inches C Commercial (transporter) 109 Load index code for single tyres 107 Load index code for twin tyres Q Speed index (Q = 160 km/h) Handling of tyres 14.5 14.5.1 14 Drive over kerbs at an obtuse angle. Otherwise the flanks of the tyres may get pinched.
14 Wheels and tyres 14.5.2 14.5.3 If alloy wheel rims are mounted and a steel spare wheel is mounted after a puncture: Do not drive any further than necessary (car dealer, car workshop, tyre dealer). Only drive at a suitable speed. The different wheels affect driving handling. Do not damage the thread of the thread bolts when changing the wheel. Tighten the wheel nuts or wheel bolts cross-wise (Fig. 199). See section 14.5.2 for tightening torque. When changing wheels (e.g.
Wheels and tyres Fig. 200 Securing support wheel Preparing the connected caravan: Preparing the disconnected caravan: Caravan - 02-08 - DET-0030-07 EN Fig. 201 Securing vehicle Loosen the stabilising device in caravan couplings with stabilising devices. Otherwise the friction pads will be highly loaded. Pull the handbrake of the towing vehicle and go to first gear or reverse gear. Park the vehicle on as even and stable a surface as possible. Apply the handbrake.
14 Wheels and tyres 14.5.4 Crank down the vehicle jack and remove it. Using the wheelbrace, tighten the wheel bolts evenly. The target value of the tightening torque of the wheel bolts is 90 Nm for steel wheel rims or 110 Nm for alloy wheel rims. Changing a wheel at alloy wheel rims 14.6 Screw in the wheel bolts and slightly tighten them cross-wise. The resting surfaces must be clean and free of burrs.
Wheels and tyres 14 As a rule of thumb it can be assumed that a filled tyre loses pressure at a rate of 0.1 bar every two months. To prevent the tyres becoming damaged or burst, check the tyre pressure regularly. The information on pressure levels is valid for cold tyres and loaded vehicles. Pressure in hot tyres must be 0.3 bar higher than in cold tyres. Recheck the pressure when the tyres are cold. Tyres Max.
14 182 Wheels and tyres Caravan - 02-08 - DET-0030-07 EN
Troubleshooting Chapter overview 15 15Troubleshooting This chapter contains instructions about possible faults in your vehicle. The faults are listed with their possible causes and corresponding remedies.
15 Troubleshooting See chapter 9 for changing the fuses. Fault Cause Remedy Road light system does no longer work correctly Bulb is defective Unscrew cover of the relevant light, replace bulb.
Troubleshooting 15 Fault Cause Remedy No voltage from the living area battery (Power Pack SE) The living area battery is discharged Charge living area battery immediately Total discharge damages the battery. If the vehicle is to be laid up for a long period, fully charge the living area battery beforehand Discharging is caused by inactive appliances (see chapter 9) Extractor hood does not work Air conditioning unit cannot be switched on or off 15.
15 Troubleshooting 15.5 15.5.1 15.5.2 Cooker Gas cooker/gas oven Fault Cause Remedy Ignition fuse does not operate (flame does not burn after the control knobs are released) Heat-up time is too short Keep control knob pressed for approx. 15 to 20 seconds after ignition Ignition fuse is defective Contact customer service Flame extinguishes when being reduced to its minimum setting Thermocouple sensor is incorrectly set Correctly reset thermocouple sensor (do not bend).
Troubleshooting 15.6.
15 Troubleshooting 15.7 Refrigerator In the event of a defect contact the nearest customer service workshop of the relevant appliance manufacturer. The list of addresses is enclosed with the accompanying appliance documentation. Only authorised qualified personnel may repair the appliance.
Troubleshooting 15 Fault Cause Remedy Air conditioning unit does not warm up No 240 V power supply Connect 240 V power supply Temperature above 30 °C Temperature has been set incorrectly Adjust the temperature Thermostat defective Contact customer service Drainage holes for condensation are clogged Clean air conditioning unit Seal is defective Contact customer service Air filter clogged Clean air filter Fan wheel defective Contact customer service Fault Cause Remedy Leakage water insi
15 Troubleshooting 15.
Special equipment 16.1 Weight details for special equipment 16 16Special equipment The use of accessories, parts and fittings not supplied by Dethleffs may cause damage to the vehicle and jeopardize road safety. Even if an expert's report, a general type approval or a design certification exists, there is no guarantee for the proper quality of the product. Every alteration of the original condition of the vehicle can alter road behaviour and jeopardize road safety.
16 192 Special equipment Item designation Surplus weight (kg) Heater cover (fireplace) 2 Heki skylight (Heki 2) 13 Insect screen door 3 Air conditioning unit (Dometic) 40 Refrigerator with freezer compartment 2 Microwave oven 15 Repair kit 1 Radio preparation 4 Satellite unit with hinged mast (BAS 60) 8 Satellite unit 19-24 Satellite antenna mast 2 Awning light 1 Hot-air system 10 Hot water supply with boiler 25 Hot water supply with hot water source 15 Water tank 3 Wint
Helpful notes 17 Chapter overview 17Helpful notes This chapter contains helpful tips for the journey. The instructions address the following topics: road assistance in European countries traffic rules in European countries gas supply in European countries toll regulations in European countries safe ways to spend the night during travel camping in winter At the end of the chapter there is a checklist containing the most important equipment for the journey. 17.
17 Helpful notes Country Greece Emergency services Police 112 171/112 Great Britain Ireland Breakdown service ELPA 104 00 1) 112 112 AA (08 00) 0 28 90 18/ (08 00) 82 82 82 1) 999/112 1) AA Dublin 18 00 66 77 88 999/112 1) Iceland 112 F.I.
17 Helpful notes Country Switzerland Emergency services Police 144 Breakdown service TCS 1 40/03 18 50 53 11 1) 117/112 1) Serbia 94 AMSS (011) 19800 92 Slovakia 155/112 1) SATC 1 81 24 158/112 1) Slovenia Spain 112 113 AMZS (1) 9 87/ (003861) 5 30 53 53 1) 061 RACE 9 15 93 33 33 112 Czech Republic 155/112 1) UAMK CR 12 30 158/112 1) Turkey 112 TTOK (02 12) 2 82 81 40 155/112 Ukraine 1) 03 112 UA (8-032) 2 97 81 12 02 Hungary 104/112 1) 107/112 1) Cyprus 112 MAK 1 88/(0036-1)
17 Helpful notes Country In built-up areas Outside built-up areas Motorway Finland 50 80 80 France 50 90 5)/110 1) 2) 6) 130 7) 2) Greece 50 80 80 Great Britain 48 80/96 1) 96 3) Ireland 50 80/100 1) 120 2) Iceland 50 80 – Italy 50 70 80 Croatia 50 80 80 Latvia 50 80 80 Lithuania 50 70 70 Luxembourg 50 75 90 Macedonia 50/60 80 80 Montenegro 50 80 80 Netherlands 50 80 80 Norway 50 60 8)/80 60 8)/80 Austria 50 100 9) 100 9) Poland 50 70/8
Helpful notes 17 4) Only with the approval of the road traffic authority for the relevant towing vehicle/ trailer combination. 5) In wet conditions 80 km/h 6) In wet conditions 100 km/h 7) In wet conditions 110 km/h 8) Trailers with no brakes and a current gross weight exceeding 300 kg 9) With trailer of over 750 kg (max. perm. gross weight of 3.5 t), the following applies: On highways 80 km/h, on motorways 100 km/h. For towing vehicles over 3.5 t perm.
17 Helpful notes Country Conditions Slovenia All year; on all roads Czech Republic All year; on all roads Hungary All year; only outside of towns Specifications without guarantee 17.5 Sleeping in the vehicle away from camping areas Country Sleeping on privately owned lands Yes Yes No Belgium X Bulgaria X Comments No X On highway rest areas max.
Helpful notes Country Sleeping on roads and fields Sleeping on privately owned lands Yes Yes No 17 Comments No Norway X X Officially prohibited on rest areas and cultivated grounds. Travelling on dirt roads is prohibited Austria X X Staying overnight for one night to restore driving ability is permitted, but not in nature reserves. Observe regional and local restrictions.
17 Helpful notes 17.6 Gas supply in European countries General tips Always observe the following instructions: 17.7 In Europe, there are several different connection systems for gas bottles. It is not always possible to fill or exchange your gas bottles in a foreign country. Get information about the connection system in the country you are travelling to before embarking on your journey, e.g. at a motoring club or in the trade press.
Helpful notes 17.10 17 Reserve your parking place in good time. Good winter camping sites are often booked up early. Do not start your trip without winter tyres. Choose your parking place with care. Observe the ground beneath you. Snow and ice may melt. Place boards of a sufficient size under the jockey wheel and the corner steadies to prevent then from sinking when the snow thaws. When the vehicle has been positioned, release the handbrake to prevent freezing.
17 Helpful notes Object Object Object Lighter Spoons Cups Bottle opener Knifes Plates Air-tight storage boxes Garbage bags Thermos jug Breakfast plate Frying pans Pots Forks Stirring spoons Glasses Bathroom/sanitary items Towels Toilet brush Toothbrush glass Sanitary items Toilet paper Living area Dustbin Insect lamp Rain clothes Road atlas Insect repellent First aid kit Bath towels Deck of cards Travel guides/parking guide Bath shoes Broom Rucksack Batteries Candles
Helpful notes Outside Documents Caravan - 02-08 - DET-0030-07 EN 17 Object Object Object Gas filling adapter Hose clips Gas tube Snow chains (winter) Stay rope Camping table Lock Bellows Luggage racks String Camping chairs Grill Tent pegs/tightening ropes List of addresses Registration book Identity card Registration confirmation(s) Driving licence Passport Allergy certificate Green insurance card Writ of protection Instruction manuals Vaccination certificate Vignette/toll c
17 204 Helpful notes Caravan - 02-08 - DET-0030-07 EN
Index 12 V fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 At the vehicle (Power Pack SE) . . . . . . . . 100 For Thetford toilet . . . . . . . . . . . . . . . . . . . 101 On the power pack . . . . . . . . . . . . . . . . . . 100 On the transformer/rectifier EBL 109 . . . . 100 12 V indicator lamp . . . . . . . . . . . . . . . . . . . . . . 97 12 V main switch . . . . . . . . . . . . . . . . . . . . . . . . 97 12 V power supply . . . . . . . . . . . . . . . . . . . . . . .
Index Caravan Correct loading . . . . . . . . . . . . . . . . . . . . . . . 31 Pitching . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Caravan coupling . . . . . . . . . . . . . . . . . . . . . . . . 26 WS 3000 D . . . . . . . . . . . . . . . . . . . . . . . . . . 27 WS 3000 D, maintenance work . . . . . . . . . 164 Caravan load . . . . . . . . . . . . . . . . . . . . . . . . 28, 32 Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 Blind . . . . . . . . . . . . . . . . .
Index Doors Conversion door . . . . . . . . . . . . . . . . . . . . . 45 Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45, 46 Troubleshooting . . . . . . . . . . . . . . . . . . . . 190 Drive-on ramp . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Driving in reverse . . . . . . . . . . . . . . . . . . . . . . . 39 Driving with the caravan . . . . . . . . . . . . . . . . . . 39 Duomatic switching facility . . . . . . . . . . . . . . . . 85 During the journey . . . . . . . . . . . . . .
Index Switching on . . . . . . . . . . . . . . . . . . . . 126, 128 Troubleshooting . . . . . . . . . . . . . . . . . . . . . 186 Gas grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Switching off . . . . . . . . . . . . . . . . . . . . . . . . 129 Switching on . . . . . . . . . . . . . . . . . . . . . . . . 129 Gas isolator taps . . . . . . . . . . . . . . . . . . . . . . . . 84 Symbols . . . . . . . . . . . . . . . . . . . . . . . . 84, 105 Gas odour . . . . . . . . . . . . . . . . .
Index Safety instructions . . . . . . . . . . . . . . . . . . . 111 Troubleshooting . . . . . . . . . . . . . . . . . . . . 187 I Indicator lamp, 12 V . . . . . . . . . . . . . . . . . . . . . 97 Indicator lamp, toilet . . . . . . . . . . . . . . . . 149, 150 Indirect lights . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Information stickers . . . . . . . . . . . . . . . . . . . . . 173 Initial start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 After temporary lay-up . . . . . . . .
Index O Odour seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Off-load voltage . . . . . . . . . . . . . . . . . . . . . . . . . 89 Operating modes Air conditioning unit (Dometic) . . . . . . . . . . 119 Refrigerator . . . . . . . . . . . . . . . . 132, 134, 137 Switching automatics, gas system . . . . . . . . 86 Oven see gas cooker or gas oven . . 126, 127, 128 Overload protection . . . . . . . . . . . . . . . . . . . . . . 94 Overrun brake . . . . . . . . . . . . . . . . . . . . . . . . .
Index Skylight with snap latch . . . . . . . . . . . . . . . . 57, 58 Blind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Opening . . . . . . . . . . . . . . . . . . . . . . . . . 57, 58 Skylights . . . . . . . . . . . . . . . . . . . . . . . . . . . 56, 59 Sleeping conversion Bench seating group and side seating group . . . . . . . . . . . . . . . . . . . . . . . 75 Round seating group . . . . . . . . . . . . . . .
Index Gas system . . . . . . . . . . . . . . . . . . . . . . . . 185 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Hot water source . . . . . . . . . . . . . . . . . . . . 186 Hot-water heater . . . . . . . . . . . . . . . . . . . . 187 Inner door . . . . . . . . . . . . . . . . . . . . . . . . . . 190 Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 Microwave oven . . . . . . . . . . . . . . . . . . . . . 186 Refrigerator . . . . . . . . . . . . . . . . . . . . . . .