User Manual

ES4200
ES4200ES4200
ES4200
DOOR MANAGEMENT ALARM
DOOR MANAGEMENT ALARMDOOR MANAGEMENT ALARM
DOOR MANAGEMENT ALARM
INSTALLATION
INSTALLATION INSTALLATION
INSTALLATION
INSTRUCTIONS
INSTRUCTIONSINSTRUCTIONS
INSTRUCTIONS
The DEFAULT SETUP is for
Access Controlled, and
Emergency Exit applications.
• This unit may be connected to power and a closed-loop Door Input
and be ready to work immediately for the Default application.
• A Voltage Sense input used with a Mag-Lock, and/or a N/C Dry
Contact Shunt input will require additional jumper configuration (J2
and/or J3 respectively) and is covered in Step 3.
• The unit is easily configured for a stand-alone Door Prop
application by removing the Intrusion Detection jumper. (LED will
always be Green when Intrusion Detection is disabled.)
Timer Setting Defaults: (Step 4)
•
Silent Time 5 seconds;
• Alarm Delay Time5 seconds
• Auto Reset Time5 seconds
• Shunt Delay 20 seconds
See text for Feature Description and Setup info.
TERMS USED IN THIS INSTRUCTION
N/C DOOR CONTACT - is a “closed-loop” circuit which goes
open when the door is opened.
SHUNT INPUT - is a dry contact Valid User Input provided by an
Access Control System or a PIR / REX device.
DMA - Door Management Alarm (i.e.: ES4200 series)
Normally Energized - in reference to a Mag-Lock or other
locking device where power is removed to unlock.
Normally De-energized - in reference to a Door Strike or other
locking device where power is applied to unlock.
ES4200
ES4200ES4200
ES4200-
--
-K1
K1 K1
K1
!"#$%&"!'#"()*$+,'$&('
64+7!ABCDEF'1&!,D2G!HBID'F%G!<&JBI!598+7!
4,,'.3.'/111'
)BJ!367!.76!:696!
www.dsigo.com
Email: [e-mail]
STEP BY STEP Jumpers: ON= short 2 pins;
OFF= one pin only.
FOLLOW THE STEP BY STEP CONFIGURATION
FOLLOW THE STEP BY STEP CONFIGURATION
FOR EASY INSTALLATION
FOR EASY INSTALLATION
FOR TROUBLE-FREE INSTALLATION, VERIFY EACH SETTING & VERIFY ANY UNUSED FEATURES ARE SET CORRECTLY FOR YOUR APPLICATION
SHUNT DELAY TIME
SHUNT RECYCLE ENABLE SHUN T CONTAC T MODE (ON =N/O)
COM
BYPASS/KEY
STATUS RELAY
COM
N/C
N/O
N/O
N/C
ES4200
SUPERV ISION EN ABLE
(ON=NORMALLY ENERGIZED)
VOLTAGE SENS E MODE
DOOR
N/O STATUS
INTRUSION DETECT ENABLE
RELAY
ALARM
RELAY
DOOR P ROP
COM
N/O
COM
N/C
DOOR
N/C
EXTENDED TIME
HORN VO LUME
(ON = HIGH)
20 SEC
10 SEC
POWER SUPPLY
12 - 24 VAC/VDC
DRY
VOLTAGE SENSE -
VOLTAGE SENSE +
RESERVED
SHUNT DELAY 0 SHUNT DELAY 1
5 SEC
0 SEC
N/O REMOTE
RESET/BYPASS
LED RED OUT
N/C DOOR
CONTACT
LED GREEN OUT
CONTACT
SHUNT
RELAY
TAMPE R
INTRUS ION &
ALARM
AUTO
RESET
SELECT
ALARM
DELAY
SELECT
SILENT
TIME
SELECT
1 2345678 9101112
13 1415 161718 19 2021 2223 24
SHUNT RECYCLE EXPLAINED
• When Shunt Recycle is Enabled (ON), a Shunt Contact or Voltage Sense
Input during the Alarm Delay warning period (beeping) will reset the Silent
Time Timer. Shunt Recycle gives the User the ability to Hold the door
indefinitely by repeating a valid input during each Alarm Delay warning.
• When disabled, only a Key or Bypass input will reset the DMA.
ACCESS CONTROL
• VOLTAGE SENSE monitors Lock Power as
“Valid User” input on TS1 (3&4)
A) If unused, Jumper 2 must be OFF.
B) If used, select: Normally Energized (Jumper 2 ON); or,
Normally De-Energized (Jumper 2 OFF)
• SHUNT INPUT detects a Dry Contact input for each valid
access. TS1 (1&2)
A) If unused, Jumper 3 must be ON
B) If used, Select:
Jumper 3 ON for N/O input; or
Jumper 3 OFF for N/C input.
• SHUNT RECYCLE
(see description below)
A) Jumper 5 is ON
B) Jumper 5 is OFF
VOLTAGE SENSE EXPLAINED
This input samples the voltage to a Mag Lock (J2 ON) or a Door Strike* (J2 OFF)
and accepts a change in voltage as a valid user input. *Normally de-energized.
SHUNT INPUT EXPLAINED
This input from a PIR or Access Control system provides user validation.
SHUNT DELAY TIME
SHUNT RECYCLE ENABLE SHUN T CONTAC T MODE (ON =N/O)
COM
BYPASS/KEY
STATUS RELAY
COM
N/C
N/O
N/O
N/C
ES4200
SUPERV ISION EN ABLE
(ON=NORMALLY ENERGIZED)
VOLTAGE SENS E MODE
DOOR
N/O S TATU S
INTRUSION DETECT ENABLE
RELAY
ALARM
RELAY
DOOR P ROP
COM
N/O
COM
N/C
DOOR
N/C
EXTENDED TIME
HORN VO LUME
(ON = HIGH)
20 SEC
10 SEC
POWER SUPPLY
12 - 24 VAC/VDC
DRY
VOLTAGE SENSE -
VOLTAGE SENSE +
RESERVED
SHUNT DELAY 0 SHUNT DELAY 1
5 SEC
0 SEC
N/O REMOTE
RESET/BYPASS
LED RED OUT
N/C DOOR
CONTACT
LED GREEN OUT
CONTACT
SHUNT
RELAY
TAMPE R
INTRUS ION &
ALARM
AUTO
RESET
SELECT
ALARM
DELAY
SELECT
SILENT
TIME
SELECT
1 2345678 9101112
13 1415 161718 19 2021 2223 24
SHUNT DELAY TIME
SHUN T RECYCLE ENABLE SHUN T CONTAC T MODE (ON =N/O)
COM
BYPASS/KEY
STATUS RELAY
COM
N/C
N/O
N/O
N/C
ES4200
SUPERV ISION EN ABLE
(ON=NORMALLY ENERGIZED)
VOLTAGE SENS E MODE
DOOR
N/O S TATU S
INTRUSION DETECT ENABLE
RELAY
ALARM
RELAY
DOOR PROP
COM
N/O
COM
N/C
DOOR
N/C
EXTENDED TIME
HORN VO LUME
(ON = HIGH)
20 SEC
10 SEC
POWER SUPPLY
12 - 24 VAC/VDC
DRY
VOLTAGE SENSE -
VOLTAGE SENSE +
RESERVED
SHUNT DELAY 0 SHUNT DELAY 1
5 SEC
0 SEC
N/O REMOTE
RESET/BYPASS
LED RED OUT
N/C DOOR
CONTACT
LED GREEN OUT
CONTACT
SHUNT
RELAY
TAMPE R
INTRUS ION &
ALARM
AUTO
RESET
SELECT
ALARM
DELAY
SELECT
SILENT
TIME
SELECT
1 234567 89101112
13 1415 1617 18 1920 2122 23 24
DOOR , SUPERVISION, AND TAMPER
• Connect N/C Door Contact to TS1 7&8.
• If resistors are installed for Door
Supervision:
A) place Jumper 1 ON and put resistors
at door switch as shown in diagram.
B) If unused, leave Jumper OFF and use a closed-loop
Door Switch circuit.
• Tamper Alarm (cannot be reset or bypassed)
A) To Enable feature cut cable tie on Tamper Switch
located on standoff (Component Location on reverse).
SHUNT DELAY TIME
SHUNT RECYCLE ENABLE SHUNT CONTACT MODE (ON=N/O)
COM
BYPASS/KEY
STATUS RELAY
COM
N/C
N/O
N/O
N/C
ES4200
SUPERVI SION EN ABLE
(ON=NORMA LLY ENERGIZED)
VOLTAGE SEN SE MODE
DOOR
N/O
STATUS
INTRUS ION DET ECT ENABLE
RELAY
ALARM
RELAY
DOOR PROP
COM
N/O
COM
N/C
DOOR
N/C
EXTENDED TIME
HORN VO LUME
(ON = HIGH)
20 SEC
10 SEC
POWER SUPPLY
12 - 24 VAC/VDC
DRY
VOLTAGE SENSE -
VOLTAGE SENSE +
RESERVED SHUN T DELAY 0 SHUN T DELAY 1
5 SEC
0 SEC
N/O REMOTE
RESET/BYPASS
LED RED OUT
N/C DOOR
CONTACT
LED GREEN OUT
CONTACT
SHUNT
RELAY
TAMPER
INTRUSION &
ALARM
AUTO
RESET
SELECT
ALARM
DELAY
SELECT
SILENT
TIME
SELECT
1 2345678 9101112
DOOR SUPERVISION EXPLAINED
Door Supervision allows the ES4200 to
monitor the circuit from the Door Contact
for open or shorted wires which may
indicate tampering. (via two 1KΩ
resistors installed as shown)
1K Ohm
1K Ohm
N/C Door
Contact
Supervised Door
To 4200
Door Input
1
INTRUSION DETECTION
A) Jumper 4 is ON for Access Control and
Emergency Exit Only applications.
B) Jumper 4 is OFF for Door Prop/Held
applications without Access Control.
NOTE: If OFF, LED is Green except during a Door Prop Alarm.
If OFF, Go to Step 4-Timer Settings. (Skip Step 3)
SHUNT DELAY TIME
SHUNT RECYCLE ENABLE SHUNT CONTACT MODE (ON=N/O)
COM
BYPASS/KEY
STATUS RELAY
COM
N/C
N/O
N/O
N/C
ES4200
SUPERV ISION EN ABLE
(ON=NORMALLY ENERGIZED)
VOLTAGE SENS E MODE
DOOR
N/O S TATU S
INTRUSION DETECT ENABLE
RELAY
ALARM
RELAY
DOOR P ROP
COM
N/O
COM
N/C
DOOR
N/C
EXTENDED TIME
HORN VO LUME
(ON = HIGH)
20 SEC
10 SEC
POWER SUPPLY
12 - 24 VAC/VDC
DRY
VOLTAGE SENSE -
VOLTAGE SENSE +
RESERVED
SHUNT DELAY 0 SHUNT DELAY 1
5 SEC
0 SEC
N/O REMOTE
RESET/BYPASS
LED RED OUT
N/C DOOR
CONTACT
LED GREEN OUT
CONTACT
SHUNT
RELAY
TAMPER
INTRUS ION &
ALARM
AUTO
RESET
SELECT
ALARM
DELAY
SELECT
SILENT
TIME
SELECT
1 2345678 9101112
13 1415 1617 18 1920 2122 23 24
2
3
ADDITIONAL OUTPUT INFORMATION
• Each of the Output functions offers the availability of monitoring a Normally
Open or a Normally Closed Dry contact.
• Each contact’s state will change to follow the status of the monitored
function.
• To combine multiple outputs, connect N/O
contacts in parallel, or N/C contacts in series.
See diagrams at right. The use of any/all Outputs
is optional.
• DSI’s ES600 (4/8/12) Zone Annunciator series,
and Custom Annunciator Panels, offer a turn-key
solution for remote monitoring. (such as Security,
Nursing, or Management stations, etc.)
• If Power is removed from the ES4200, each
contact in it’s normal state (powered), will change state. Example: Door
Status will appear as if the door has been opened; Alarm and Bypass
contacts will appear as if an alarm or bypass condition exists.
N/O
To Monitoring Equip.
To Monitoring Equip.
N/C
OUTPUTS (FORM-C)
• DOOR STATUS RELAY TS2-
22,23,24 changes state when the
Door Input changes. Used to monitor
changes in Door Contact status.
•
DOOR PROP ALARM RELAY
TS2-19,20,21 changes state when a
door is held open beyond the Silent
and Alarm Delay time, combined.
•
FORCED DOOR/TAMPER
ALARM RELAY TS2-16,17,18
changes state when a door is forced or a tamper
condition exists (Door Supervision/Tamper Switch).
•
BYPASS/KEY SWITCH STATUS RELAY TS2-
13,14,15 changes state during Bypass (TS1 9&10) and
Key Switch Inputs. Used to monitor for changes in
Bypass status.
SHUNT CONTACT MODE (ON=N/O)
COM
BYPASS/KEY
STATUS RELAY
COM
N/C
N/O
N/O
N/C
ES4200
SUPERVISION ENABLE
(ON=NORMALLY ENERGIZED)
VOLTAGE SENSE MODE
DOOR
N/O
STATUS
RELAY
ALARM
RELAY
DOOR PROP
COM
N/O
COM
N/C
DOOR
N/C
RELAY
TAMPER
INTRUSION &
ALARM
AUTO
RESET
SELECT
1314151617 18 19 20 21 22 23 24
6
TIMER SETTINGS SEE TABLE ON REVERSE
•
The SHUNT DELAY TIMER begins after a
Valid User input (prior to door being opened)
and if door is not opened
the DMA will reset
when timer expires. Cancels upon door opening.
A) Shunt Delay works only with Intrusion Detection
enabled.
B) See table on Back Plate for Jumper 7&8 setting detail.
•
SILENT TIME SELECT begins when the door is opened
by a valid user. (see Timer Setting Table on reverse)
A) Timer has two ranges selected with Jumper 9;
• Normal - 0 seconds to 2.5 minutes (Jumper OFF)
• Extended - 3 minutes to 90 minutes (Jumper ON)
B) After selecting appropriate range, turn dial to SET # for
the Silent Time period desired for your application.
•
ALARM DELAY SELECT begins on the expiration of the
Silent Timer. Warning Alarm sounds locally to alert user.
A) Turn dial to SET # on table (see reverse) for the time
you want the Warning (beeping) alarm to sound (prior
to triggering the Door Prop Alarm Horn and Relay).
•
AUTO RESET TIME SELECT is the minimum time the
Horn, LED and Relays are on following an alarm condition.
NOTE: Alarm will continue for as long as the door is open.
A) Turn the dial to SET Timer (0 seconds to 5 minutes, or
Manual).
SHUNT DELAY TIME
SHUNT RECYCLE ENABLE SHUNT CONTACT MODE (ON=N/O)
COM
BYPASS/KEY
STATUS RELAY
COM
N/C
N/O
N/O
N/C
ES4200
SUPERV ISION EN ABLE
(ON=NORMALLY ENERGIZED)
VOLTAGE SENS E MODE
DOOR
N/O S TATU S
INTRUSION DETECT ENABLE
RELAY
ALARM
RELAY
DOOR P ROP
COM
N/O
COM
N/C
DOOR
N/C
EXTENDED TIME
HORN VO LUME
(ON = HIGH)
20 SEC
10 SEC
POWER SUPPLY
12 - 24 VAC/VDC
DRY
VOLTAGE SENSE -
VOLTAGE SENSE +
RESERVED
SHUNT DELAY 0 SHUNT DELAY 1
5 SEC
0 SEC
N/O REMOTE
RESET/BYPASS
LED RED OUT
N/C DOOR
CONTACT
LED GREEN OUT
CONTACT
SHUNT
RELAY
TAMPE R
INTRUS ION &
ALARM
AUTO
RESET
SELECT
ALARM
DELAY
SELECT
SILENT
TIME
SELECT
1 23456789101112
13 1415 1617 18 1920 2122 23 24
4
POWER
• POWER - Connect 12-24 VAC/DC
to TS1 11&12. Not polarity sensitive.
5
SHUNT DEL AY TIME
SHUNT RECYCLE ENABLE SHUNT CONTACT MODE (ON=N/O)
COM
BYPASS/KEY
STATUS RELAY
COM
N/C
N/O
N/O
N/C
ES4200
SUPERVIS ION ENABLE
(ON= NO RMAL LY E NER GIZ ED )
VOLTAGE SE NSE MODE
DOOR
N/O S TATUS
INTRUSION DETECT ENABLE
RELAY
ALARM
RELAY
DOOR PROP
COM
N/O
COM
N/C
DOOR
N/C
EXTENDED TIME
HORN VO LUME
(ON = HIGH)
20 SEC
10 SEC
POWER SUPPLY
12 - 24 VAC/VDC
DRY
VOLTAGE SEN SE -
VOLTAGE SEN SE +
RESERVED
SHUNT DELAY 0 SHUNT DELAY 1
5 SEC
0 SEC
N/O REMOTE
RESET/BYPASS
LED RED OUT
N/C DOOR
CONTACT
LED GREEN OUT
CONTACT
SHUNT
RELAY
TAMPER
INTRUSION &
ALARM
AUTO
RESET
SELECT
ALARM
DELAY
SELECT
SILENT
TIME
SELECT
1 234567 89101112
13 1415 1617 18 1920 2122 23 24
ADDITIONAL FEATURES
• BYPASS TS1 (9&10) input, to N/O
contact to remotely Bypass or Reset the
unit.
• REMOTE LED to TS1 (5&6). (from
DSI ES450 with Bi-color LED)
• HORN VOLUME - Jumper 10 is
used to set the volume of the
sounder. ON = 103db
OFF = 96db
SHUNT DELAY TIME
SHUNT RECYCLE ENABLE SHUNT CONTACT MODE (ON=N/O)
COM
BYPASS/KEY
STATUS RELAY
COM
N/C
N/O
N/O
N/C
ES4200
SUPERV ISION EN ABLE
(ON=NORMALLY ENERGIZED)
VOLTAGE SENS E MODE
DOOR
N/O S TATU S
INTRUSION DETECT ENABLE
RELAY
ALARM
RELAY
DOOR PROP
COM
N/O
COM
N/C
DOOR
N/C
EXTENDED TIME HORN VOLUME
(ON = HIGH)
20 SEC
10 SEC
POWER SUPPLY
12 - 24 VAC/VDC
DRY
VOLTAGE SENSE -
VOLTAGE SENSE +
RESERVED SHUNT DELAY 0 SHUNT DELAY 1
5 SEC
0 SEC
N/O REMOTE
RESET/BYPASS
LED RED OUT
N/C DOOR
CONTACT
LED GREEN OUT
CONTACT
SHUNT
RELAY
TAMPE R
INTRUS ION &
ALARM
AUTO
RESET
SELECT
ALARM
DELAY
SELECT
SILENT
TIME
SELECT
1 23456789101112
1314 15 1617 1819 2021 22 2324
SHUNT DELAY TIME
SHUNT RECYCLE ENABLE SHUNT CONTACT MODE (ON=N/O)
COM
BYPASS/KEY
STATUS RELAY
COM
N/C
N/O
N/O
N/C
ES4200
SUPERV ISION EN ABLE
(ON=NORMALLY ENERGIZED)
VOLTAGE SENS E MODE
DOOR
N/O S TATU S
INTRUS ION D ETEC T EN ABLE
RELAY
ALARM
RELAY
DOOR PROP
COM
N/O
COM
N/C
DOOR
N/C
EXTENDED TIME HORN VOLUME
(ON = HIGH)
20 SEC
10 SEC
POWER SUPPLY
12 - 24 VAC/VDC
DRY
VOLTAGE SENSE -
VOLTAGE SENSE +
RESERVED SHUNT DELAY 0 SHUNT DELAY 1
5 SEC
0 SEC
N/O REMOTE
RESET/BYPASS
LED RED OUT
N/C DOOR
CONTACT
LED GREEN OUT
CONTACT
SHUNT
RELAY
TAMPE R
INTRUS ION &
ALARM
AUTO
RESET
SELECT
ALARM
DELAY
SELECT
SILENT
TIME
SELECT
1 23456789101112
1314 15 1617 1819 2021 2223 24
7
SHUNT DELAY TIME
SHUN T RECYCLE ENABLE SHUNT CONTACT MODE (ON=N/O)
COM
BYPASS/KEY
STA TUS RE LAY
COM
N/C
N/O
N/O
N/C
ES4200
SUPERVI SION ENABL E
(ON=NORMALLY ENERGIZED)
VOLTAGE S ENSE MODE
DOO R
N/O STATUS
INTRUSION DETECT ENABLE
RELAY
ALAR M
RELAY
DOOR PROP
COM
N/O
COM
N/C
DOOR
N/C
EXTENDED TIME
HORN VO LUME
(ON = HIGH)
20 SEC
10 SEC
POWER SUPPLY
12 - 24 VAC/VDC
DRY
VOLTAGE SEN SE -
VOLT AGE SENS E +
RESERVED
SHUNT DELAY 0 SHUNT DELAY 1
5 SEC
0 SEC
N/O R EMOTE
RESET/BYPASS
LED RED OUT
N/C DOOR
CONTACT
LED GREEN OUT
CONTACT
SHUNT
RELAY
TAMPER
INTRUS ION &
ALARM
AU TO
RESET
SELECT
ALAR M
DELAY
SELECT
SILENT
TIME
SELECT
1 2345678 9101112
13 1415 1617 18 1920 2122 23 24
*COMPONENT LOCATION INFO ON REVERSE*