ProDoc Series DHRWM Digital Height Rod (Wall Mounted Digital Height Rod) Owner’s Manual 0044-M372-O1 Rev A 05/08 CARDINAL SCALE MFG. CO. PO Box 151 y Webb City, MO 64870 Ph: 417-673-4631 y Fax: 417-673-5001 www.detectoscale.com Technical Support: Ph: 866-254-8261 y techsupport@cardet.
0044-M372-O1 y DHRWM Page 2
INTRODUCTION Thank you for purchasing our Detecto ProDoc Series DHRWM Wall Mounted Digital Height Rod. Your digital height rod has been designed for simple and straightforward use and to assure accuracy and dependability for years to come. Please read this manual thoroughly before attempting to use your scale and keep it handy for future reference. It contains important instructions for installation and proper operation of your scale.
SPECIFICATIONS Height Units ......………………… Feet/Inches or Centimeters (selectable) Height Range…………………….. 3’ 7” to 6’ 7” (110 to 200 cm) Power Requirements …………… Four (4) “AA” size Alkaline batteries (not included) Display …………………………… Five digit, seven segment, 1.0 inch (25 mm) high LCD Cable Length ……………………. 69” (175 cm) Operation Temperature ………… 50 to 104 ºF (+10 to +40 ºC) Function Keys …………………… UNITS and ON/OFF Dimensions Display ..…………..…............. 5.25” H x 7.75” W x 2.125” D (13.4 cm x 19.
UNPACKING Remove the height rod, display, hardware pack and other components from the shipping carton. After removing from the carton, check for any damage that may have taken place during shipment. Keep and use the original carton and packing material for return shipment if it should become necessary. The purchaser is responsible for filing all claims for any damages or loss incurred during transit.
INSTALLATION Mounting the Height Rod 1. Choose the location to mount the height rod on the wall. The location should be free of temperature extremes and water. It should be where it is within easy reach of the operator. 2. Make certain the structure and mounting hardware are of sufficient strength to support the height rod. The mounting bracket should be securely fastened to the wall so that it cannot break loose from the mounting surface. 3. Referring to Figure No.
INSTALLATION Mounting the Display The DHRWM display has a 69” (175 cm) cable to allow it to be placed at a convenient position away from the height rod. A bracket is included to mount the display on a wall or the bracket (and included feet) can used to place it on a desk for easy viewing. Wall Mounting 1. Choose the location to mount the display on the wall. The location should be free of temperature extremes and water.
INSTALLATION Wall Mounting, Cont. 7. Referring to Figure No. 3, make sure the four (4) feet of Display Wall Bracket “A” are placed in the bracket. Display Feet (for Desk or Table Mounting) Display Wall Bracket “A” Figure No. 3 Figure No. 4 8. Next, locate the four (4) slots on the back of the display and align them with the four (4) tabs on the Display Wall Bracket “A”. Refer to Figure No. 4. 9. Insert the tabs into the slots and press together until the bracket locks to the back of the display. 10.
INSTALLATION Desk or Table Mounting 1. The location chosen should be a stable, level surface (either a desk or solid table), free of temperature extremes and water. The display should be where it can be easily viewed, not subject to direct sunlight and where the keypad is within easy reach of the operator. 2. Referring to Figure No. 6, remove the four (4) feet from inside Wall Bracket “A” and install them in each corner of the bracket as shown in Figure No. 7.
BATTERY OPERATION Battery operation is a standard feature of the ProDoc Series Wall Mounted Digital Height Rod, although the batteries are optional (not included). You must first obtain and install four (4) "AA" size alkaline batteries before operations can begin. Batteries are contained in a battery holder inside the display. Access is via a removable cover on the back of the display. Installation / Replacement To install or remove the batteries, the following steps should be followed: 1.
OPERATION Keypad Functions DO NOT operate the keypad with pointed objects (pencils, pens, etc). Damage to keypad resulting from this practice is NOT covered under warranty. The UNITS key is used to change the height units between feet/inches and centimeters. With the display off, pressing the ON/OFF key will apply power and turn on the display. If the display is on, pressing it will turn the display off. Annunciators Figure No.
0044-M372-O1 y DHRWM Page 10
