Specifications

Code
Explanation
R—Repair parts and assemblies that are eco-
nomically repairable at DSU and GSU
activities and are normally furnished
by supply on an exchange basis.
T—High-dollar value recoverable repair parts
which are subject to special handling
and are issued on an exchange basis.
Such repair parts normally are repaired
or overhauled at depot maintenance ac-
tivities.
b. Federal Stock Number, Column
Z. This
column indicates the Federal stock number as-
signed to the item and will be used for requi-
sitioning purposes.
c. Description, Column 3. This column indi-
cates the Federal item name and any additional
description of the item required. A part number
or other reference number is followed by the
applicable five-digit Federal supply code for
manufacturers in parentheses.
d. Unit of Meaaure (U/M), Column 4. A two-
character alphabetic abbreviation indicating the
amount or quantity of the item upon which the
allowances are based, e.g., ft, ea, pr, etc.
e. Quantity Incorporated in Unit, Column 5.
This column indicates the quantity of the item
used in the AN/VRM-1 and AN/VRM-1A.
f. Allowances (30-Day DS/GS Maintenance,
1 Year Per Equipment (Contingency), and De-
pot Maintenance) Columns 6, 7, 8, and 9. Items
authorized for requisition as required are
identified with an asterisk in the allowance
column.
g. Illustrations, Column 10. This column is
divided as follows:
(1) Figure number, column 10a. Indicates
the figure number in which the item is shown.
(2) Item number or reference designation,
column 10b. Indicates the reference designation
used to identify the item in the illustration.
1-4. Special Information
Identification of the usable on codes included in
column 3 of section II are-
Code
Used on-
A
B
AN/VRM-1
------ ------ ------ ------ -
AN/VRM-1A
----- ----- ----- ----- ------
NOTE
Where no usable codes are indicated,
item is applicable to all models.
1-5. Location of Repair Parts
a. This manual contains two cross-reference
indexes (sees. III and IV) to be used to locate
a repair part when either the Federal stock
number, reference number (manufacturer’s
part number), or reference designation is
known. The first column in each index is pre-
pared in numerical or alphanumerical sequence
in ascending order. Where a federal stock num-
ber is not listed, refer to the reference number
(manufacturer’s part number) immediately
following the Federal stock number column.
b. When the Federal stock number or refer-
ence number is known, follow the procedures
given in (1) and (2) below.
(1) Refer to the index of Federal stock
numbers (sec. HI) and locate the Federal stock
number or reference number. The Federal stock
number or reference number is cross-referenced
to the applicable figure and reference designa-
tion.
(2) When the reference designation is de-
termined, refer to the reference designation
index (sec. IV). The reference designations are
listed in alphanumeric ascending order and are
cross-referenced to the page number on which
they appear in the repair parts list (see II).
Refer to the page number noted in the index
and locate the reference designation in the re-
pair parts list (col. 10b).
c. When the reference designation is known,
follow the procedures given in b(2) above.
d. When neither the Federal stock number,
reference number, nor reference designation is
known, identify the part in the illustration and
follow directions given in c above; or scrutinize
column 3 of the repair parts list (sec. H).
1-6. Federal Supply Code for Manufacturers
Coda
13467 ---- . . .
71468 ----
72619
74970 -
80063 --- .
80294 - ----
81349 .- --
88044
96906 .-
Manufacturer
Electrospace Corporation
ITT Cannon Electric, Inc.
Dialight Corporation
E. F. Johnson Co.
Army Electronics Command .
Procurement and Produc-
tion Directorate
Bourns, Inc.
Military Specifications
Aeronautical Standards
Military Standards
2