Specifications

DS7400Xi Ver. 3+ Reference Guide Copyright © 1995-96 Detection Systems, Inc. Page 51
12.28 Phone Number General Control Programming: Program Address (0528)
Example:
To program the parameters to enable the Remote Pro-
grammer Call-back feature, to dial Pulse on all Phone
Numbers, to send Alarm Reports via either ARDIS or Digi-
tal, and to use 110 Baud comm. for WDSRP.
Data Digit 1 = [1], Data Digit 2 = [0].
Enter the Programmer’s Mode: [9] [8] [7] [6] [#] [0]
Enter the Program Address: [0] [5] [2] [8]
Enter Data Digit 1: [1]
Enter Data Digit 2: [0]
Enter the pound key: [#]
Program the next Address, Program a different Address,
or Exit the Programmer’s Mode.
4
Dial tone on all phone numbers**
Enter the Data Digit as a:
Select Options 210 3 5 6 7 8
Enable remote programmer call-back
Dial pulse on all phone numbers
Dial tone, switch to pulse if required
∆ ∆ Try ARDIS network first
9 *0 *1
*0 - *1 are Hex values. They will display as A - B at the keypads.
∆∆ = If this option is selected, see address 0494-0495.
** = Required on PBX systems
Data Digit
12
Send alarms via either ARDIS or digital ∆
Enter the Data Digit as a:
Select Options 0 1 2 3 4 5 6 7 8
Dialer delay of 15 sec. on non-24H burglar alarms only**
Dialer delay of 15 sec. on 24H burglar & fire alarms only**
∆ ∆ Send alarms via both ARDIS and digital ∆***
Use 110 Baud comm. for WDSRP
9 *0 *1
*0 - *5 are Hex values. They will display as A - F at the keypads.
∆ = Only applicable when using the ARDIS option.
∆ ∆ = If this option is selected, see address 0494-0495.
** = These selections can only be used with systems that have only one partition.
*** = This selection must be chosen for U. L. Certificated installations when using the ARDIS module.
Use 300 Baud comm. for WDSRP
*2 *3 *4 *5
See Glossary (section 7.14) for further details.
12.29 Phone Number Format Programming: Program Addresses (0529-0530)
Note:
Phone Number 1 Format = Address 0529
Phone Number 2 Format = Address 0530
When using the ARDIS communications
module:
Program address 0529 as: data digit 1 =
9, data digit 2 = 1.
Program address 0530 as: data digit 1 =
9, data digit 2 = 1.
Enter the DD as a:
Select Options
DDSelect Option
Data Digit
12
012345
1900 Hz. Data/1400 Hz. Acknowledge
1800 Hz. Data/2300 Hz. Acknowledge
BFSK, SIA, Contact ID
10 Pulses per Second (PPS)
20 Pulses per Second (PPS)
40 Pulses per Second (PPS)
0
Phone Number Disabled
3/1 (no Extended Reporting)
3/1E (Extended Reporting)
1
2
3/1 with Parity
3
3/1E with Parity
4
4/1
5
4/2
6
BFSK
7
SIA 110 Baud
8
Contact ID
9
0
SIA 300 Baud
*0
*0 and *5 are Hex values. They will display as A and F at the keypads.
Pager
*5