Specifications

DS7400Xi Ver. 3+ Reference Guide Copyright © 1995-96 Detection Systems, Inc. Page 44
12.16 Open/Close Report Control Programming: Program Address (0187)
Example:
To program to send Open/Close Reports from Partition 1 and to send
Trouble Reports on Closings for all Bypassed Zones.
Data Digit 1 = [1], Data Digit 2 = [1].
Enter the Programmer’s Mode: [9] [8] [7] [6] [#] [0]
Enter the Program Address: [0] [1] [8] [7]
Enter Data Digit 1: [1]
Enter Data Digit 2: [1]
Enter the pound key: [#]
Program the next Address, Program a different Address, or Exit the
Programmer’s Mode.
4Select Options 0 1 2 3 5 6 7 8 9
Do not report opens or closes
Report opens and closes in Partition 1
Report opens and closes in Partition 2
Report opens and closes in Partition 3
Report first Partition to open and last
Partition to close**
Report opens and closes in Partition 4
Enter the Data Digit as a:
** = When using this option, all parti-
tions should have the same ac-
count code.
Send Trouble at Close
for Bypassed Zones
Data Digit
12
Do Not Send Trouble
at Close for Bypassed
Zones
1
0
Report opens and closes in Partition 5
Report opens and closes in Partition 6
Report opens and closes in Partition 7
Report opens and closes in Partition 8
See Glossary (section 7.12) for further details.
12.17 Open/Close & Zone Report Control Programming: Program Address (0189)
This section allows you to decide which phone number will send open and close reports, zone alarm, zone restoral, and zone trouble
reports.
Example:
To program to send Open and Close Reports
to Phone Number 1 and Zone Alarm, Zone
Restoral, and Zone Trouble Reports to Phone
Number 2.
Data Digit 1 = [1], Data Digit 2 = [2].
Enter the Programmer’s Mode:
[9] [8] [7] [6] [#] [0]
Enter the Program Address: [0] [1] [8] [9]
Enter Data Digit 1: [1]
Enter Data Digit 2: [2]
Enter the pound key: [#]
Program the next Address, Program a differ-
ent Address, or Exit the Programmer’s Mode.
Data Digit 2
is for Zone Alarm,
Zone Restoral,
and Zone Trouble
Reports.
DDSelect Option
DD
Alternate between both Phone Numbers
0
0
Alternate between both Phone Numbers
Report to Phone Number 1
Report to Phone Number 2
1
2
Report to Phone Number 1 and 2
3
Report to Phone Number 1
Report to Phone Number 2
1
2
Report to Phone Number 1 and 2
3
12
Data Digit 1 is
for Open and
Close Reports.
Select Option
Data Digit
12.18 Report Control Programming: Program Address (0190)
Example:
To program all other Reports to Phone Num-
ber 2.
Data Digit 1 = [2], Data Digit 2 = [0].
Enter the Programmer’s Mode:
[9] [8] [7] [6] [#] [0]
Enter the Program Address: [0] [1] [9] [0]
Enter Data Digit 1: [2]
Enter Data Digit 2: [0]
Enter the pound key: [#]
Program the next Address, Program a differ-
ent Address, or Exit the Programmer’s Mode.
Note: Data Digit
1 does not
include open and
close reports or
zone reports (see
sections 12.16
and 12.17).
DD
Alternate between both Phone Numbers
0
Report to Phone Number 1
Report to Phone Number 2
1
2
Report to Phone Number 1 and 2
3
12
Select Option
Data Digit
0
Data Digit 2
must be 0
This section allows you to decide which phone number will send reports other than open/close reports and zone reports.