Specifications

ManualsBrandsDetection Systems ManualsHome building and DecorDS7060

1.0 Specifications

1.1 Enclosure Housing

1. The standard enclosure is manufactured from 20 Ga., cold-rolled

steel, and measures 12.5" Wide, by 14.5" High, by 3" Deep (31.8

cm Wide, by 36.8 cm High, by 7.6 cm Deep). A keyed lock is includ-

ed, and this enclosure has provision for an optional tamper switch

(required for commercial burglary applications) for monitoring the

door.

1.2 Temperature

• Storage and Operating Temperature: +32° to +120°F

(0° to +49°C)

1.3 Power

NOTE: The total current output capacity for all auxiliary devices,

including keypads and smoke detectors = 1.5 A standby,

2.5 A alarm. The following ratings are maximum values.

The total combined output cannot exceed the max. load

current.

• Input power: 18 VAC, 50 VA, 50 Hz./60 Hz.

• Auxiliary regulated power: 12 VDC, 1.0 A max.

• U. L. Listed Auxiliary power: 12 VDC, 1.0 A max.

• U. L. Listed Alarm Power Output: 12 VDC, 1.75 A max.

• Auxiliary power voltage range: 12 V special application

• Optional Standby battery (P334): 12 V, 7.0 AH - 35 AH max.

• Control panel current draw: 175 mA, Standby

250 mA, Alarm

1.4 Outputs

• Alarm Output: 12 VDC, 1.75 A output. Can be pro

grammed for steady or pulsed out-

put.

• Programmable Output 1* Solid state current sink (1.0 A max.).

Shorts to ground when activated.

Connect device to Aux. power pos-

itive. Can be used for alarm, arm-

ing state, or access control.** This

output is generally programmable.

• Programmable Output 2* Solid state voltage source (500 mA

max.). Can be used for alarm, arm-

ing state, or access control.**

This output is generally programma-

ble. For use with such compatible

devices as the Listed DS250 with a

4-wire base.

* = Current draw should be subtracted from either maximum

auxiliary or maximum alarm current draw.

** = Not investigated to the requirements of UL294.

1.5 Zones

• 8 on-board zones. Up to 128 total zones with expansion modules.

• Zone Response Time: 300 ms.

1.6 Keypads

• Maximum # of keypads: 15 Keypads

• Maximum wire length each: 1000 feet (305 m)

• Maximum wire length total: 6000 feet (1830 m)

in system

• Wire type: 4 conductor, unshielded, #22

AWG (0.8 mm) “Telephone

quad” or #18 AWG (1.0 mm)

quad wiring can be home-run

or daisy- chained.

NOTE: No more than 2 keypads (#22 AWG) or 3 keypads (#18

AWG) are recommended on any 1000 foot (305 m) run.

NOTE: Shared cable is not recommended for keypad, multiplex,

options bus, telephone, or siren wiring.

1.7 Communicator

Will report to two phone numbers with full single, double and back-

up reporting. Communicates in SIA (110 or 300 baud), 3/1, 3/1 Ext.,

3/1 with Parity, 3/1 Ext. with Parity, 4/1, 4/2, BFSK, Contact ID, and

Pager formats.

FCC Registration Number is ESVUSA-75333-AL-E

The ringer equivalence is 0.1B

Commercial Fire CSFM Listing Number is 7165-1062:111

Residential Fire CSFM Listing Number is 7167-1062:111

1.8 Partitions

The system has the capacity for 8 independant partitions.

1.9 Users

The DS7400Xi system allows up to 90 individual users. Each user

will have his own PIN number (the 4 digit code entered at the key-

pads) and his own authority level (to determine which functions he

may perform).

1.10 Lightning Protection

MOVs and spark gaps provide protection from lightning surges and

static discharges.

1.11 Burglar/Fire Zone Inputs

• Number of circuits: 8 Circuits on-board

• End-of-line resistor: 2.2 K Ω (P/N 25944, provided)

• Loop resistance tolerance: 60 ohms

1.12 Fire Signal Initiating Circuit (2-wire mode)

Fire circuit will work with 2 or 4-wire detectors and has optional alarm

verification.

• Number of circuits: 8 Circuits on-board

• Type of circuit: Class B, latching

• End-of-line resistor: 2.2 K Ω (P/N 25944, provided)

• Supervisory current: 5.5 mA

• Maximum short circuit current: 22 mA

• Maximum line resistance: 60 ohms

• Circuit voltage range: 8.5 to 14.1 VDC

• Total detector standby current: 2.5 mA

1.13 Multiplex Bus Wiring Requirements

• #22 AWG (0.8 mm). Up to 2000 feet (610 m) per system.

• #18 AWG (1.0 mm). Up to 5000 feet (1525 m) per system.

1.14 Option Bus Wiring Requirements

• Maximum wire length 1000 feet (305 m) per home-run.

1.15 Max. Load Currents

Max. Current By Output:

Not to exceed the max. load

currents listed above per column.

Option Power

Standby Alarm

U. L. Installations

Non-U. L. Applications

Aux. Power & Keypad (Combined)

Bell Output

Programmable Output 2

Loop Power +

1.5 A

2.0 A

1.0 A

500 mA

2.5 A

1.0 A

1.75 A

500 mA

Max. Load Currents