Specifications

ManualsBrandsDetection Systems ManualsHome building and DecorDS7060

8.13.6 Error Displays

System fault 01

System fault 02

System fault 03

System fault 04

System fault 10

System fault 11

System fault 12

System fault 13

System fault 14

System fault 20

System fault 50

System fault 51

System fault 52

System fault 53

System fault 54

System fault 55

System fault 56

System fault 57

System fault 58

System fault 59

RAM Fault

ROM Fault

EEPROM Fault

Ground Fault

2Ph/Bell Fault = loss of communication to DS7420i

Line 1 Fault = DS7420i phone line 1 fault

Line 2 Fault = DS7420i phone line 2 fault

Bell Fault = DS7420i bell circuit fault

Aux. Relay Fault = DS7420i aux. relay fault

Oct. Relay Fault = loss of communication to DS7488

Reserved for older panels

AR IB Queue Full = modem buffer full

AR Host Down = network data switch down

AR Unreg. Modem = modem not registered

AR Power Fail = power source below defined threshold

AR Network Lost = loss of network

AR Modem HW Err = modem hardware error

AR Modem SW Err = modem software error

AR Opt. Bus Err = loss of communication to ARDIS module

AR Corrupt MSG = message error

Read Error display when

green Power light is flashing.

Clear Error Display*

Caution: Clear the error display only on the advice of your installing

company or if you are certain the problem has been remedied.

1. DS7447 - “AC Power Failure” / DS7445 - LED 1 turns

on steady: There is a power failure and the panel is

operating on backup battery.

2. DS7447 - “Battery Trouble” / DS7445 - LED 2 turns on

steady: If the system has just been through a power

failure, wait at least two hours for the battery to recharge,

then enter a PIN + [System Reset] to perform a battery test.

3. DS7447 - “Communicator Err” / DS7445 - LED 3 turns

on steady: The communicator failed to communicate

with the central station.

4. DS7447 - “System Fault” / DS7445 - LED 4 turns on

steady: Internal error in the control circuitry or

optional circuitry. These faults are designated as follows:

This chart explains the procedure for reading Error displays

when the green Power Light is flashing on the keypad.

Control panel problems are indicated by a flashing green Power Light. The DS7447 display

will also read “Control Trouble, Enter #87.” The DS7445 will only flash the green Power Light.

The Error displays may only be read when the control is disarmed.

Contact your installing company if the problems persist.

Action Desired Command Sequence

5. DS7447 - “Keypad Fault” / DS7445 - LED 5 turns on

steady: One of the keypads is not responding to the

control panel.

6. DS7447 - “Multiplex Bus” / DS7445 - LED 7 turns on

steady: The multiplex bus is defective or has been

shorted.

7. DS7447 - “Aux Power Fault” / DS7445 - LED 8 turns on

steady: The auxiliary power has been shorted.

8. DS7447 - “Zone Trouble”: One of the zones is not

responding to the control panel. This may also be

displayed during power-up (if so, ignore).

* = Battery Trouble display will only clear by the [System Reset] command or another automatic battery test even after the problem has been

remedied. Comm Error display willonly clear by the [System Reset] command or the next successful automatic system off normal report

even after the problem has been remedied. All the other error displays will self clear from the keypads once the problem has been remedied.

#87 will display #89 will display

Note: System Faults may be

read from any keypad because

they are system-wide.

All other Error Displays are limit-

ed to the partition the Standard

keypad is in. If you are on a Mas-

ter keypad, you may read Error

Displays one partition at a time.

PIN + [#] [8] [7]

PIN + [System Reset]