Specifications

ManualsBrandsDetection Systems ManualsHome building and DecorDS7060

8.0 Operating Guide

8.1 Personal Identification Numbers

8.1.1 General Information

When programming Personal Identification Numbers, it is helpful to

know the following terms:

• PIN: Personal Identification Number. This is the 4 digit code us-

ers must enter at the keypad to gain access to the system. A PIN

may be assigned to each User Number 001 through 090.

• User Number: This is the number that identifies each person

using the system. There are 90 possible User Numbers available

for use (001 through 090)

• Authority Level: This number determines which functions each

user will be able to perform.

Your system has the capability to assign up to 90 PINs, each four

digits long. Each User Number can have only one PIN assigned to

it. Attempting to assign the same PIN to multiple User Numbers will

result in the three-beep error tone, and the entry will not be made.

User Number 001 is designated as a Master code. It can be used to

add, delete, or change other PINs. It will always have access to all

partitions regardless of how it is programmed.

User Number 001 is shipped from the factory with the PIN of 1 2 3

4. This PIN should be changed to one of your personal preference

and must be programmed as a Master code.

PINs should never be programmed with common sequences such

as 1 2 3 4, 1 1 1 1, or 2 4 6 8 because they are easily violated.

8.1.2 Removing a PIN

To disable (remove) a PIN, enter:

• A Master code, followed by [#] [0].

• [0]

• User number of the PIN to be cancelled, followed by [#]

User Number 001 can not be disabled in this manner.

8.1.3 Authority Levels

0 = Master: Can enter all commands, add or change PINs in all

partitions, change time and date, bypass, arm, disarm, perform

system tests, system reset, and view history. Any or all PINs

can behave as a Master code.

1 = Unlimited: Can enter all commands, bypass, arm, disarm, sys-

tem reset, and perform system tests. Can not change PINs.

2 = General: Can bypass, arm, and disarm. Can not change PINs,

system reset, or enter Command 7 or any of the Command 8

functions. Bypass and disarm are programmable by partition.

3 = Arm Only: Can arm the system with [On] arming only. Can not

perform any other functions including disarming.

4 = Temporary: Valid only for a specified time (PIN will disappear

upon expiration date). Can arm and disarm the system, but can

not perform any other functions. If this function is performed

from a Master Keypad, you must be in Single Partition Mode.

5 = Duress: When the system is disarmed using the duress PIN, a

silent report is sent to the central station. The Duress PIN is

intended to be used when the user is forced to disarm the sys-

tem.

6 = Access: When a PIN with an Access code is entered, any

output programmed for Access Output (e.g. door strikes) will

pulse on for 10 seconds (works when the system is armed or

disarmed).

This chart will guide you through the steps necessary to change a PIN.

# 1. Enter the Master Code Pro-

gramming Mode.

“0 User Change”

(display will scroll to this)

[Master Code] + [#] [0]

Steps to Change a

Command

Sequence

If Accepted, the Display Reads

# 2. Enter a 0.

[0]

“Enter User No.”

(001..0XX)

# 3. Enter the User Number.

[0] [0] [1]

through

[0] [9] [0]

“Enter Authority Level”

Level (0-6)

# 4. Enter the Authority Level.

[0]

through

[6]

“Enter Area(s) or # for all”

# 5. Enter the Area(s) (partition(s))

this user has access to.

[1], [2], [3], [4], [5], [6],

[7],

and/or

[8]

then

[#]

# 6. Enter the PIN.

Any

digits.

Do not press [#].

“Enter PIN Again. End with #”

A long beep will sound to signify

acceptance of the new PIN.

# 7. Enter the PIN again followed by

the [#] key.

PIN (same 4 digits as above),

then [#].

“Enter Next Area, End with #” or

“Enter PIN”

It is recommended that this procedure be performed at a DS7447 keypad. No visual cues will be given from a DS7445 keypad.