CHIPPER ASSEMBLY GUIDE MODEL: OPC566E 6 INCH KINETIC DRUM CHIPPER DETAIL K2 INC. DK2 POWER USA 4301 S Valley View Blvd STE 10-11 Las Vegas, NV 89103 1-702-331-5353 DETAIL K2, INC. 1080 Clay Avenue Unit 2 Burlington, Ontario, Canada L7L0A1 DK2 USA EAST 6245 Industrial Parkway Whitehouse, OH 43571 PARTS AND SERVICE 702-331-5353 OR WWW.DK2POWER.
STEP 1: Open and unpack all items. Leave lots of working space. Inspect all parts. The CHIPPER is shipped in a crate. Remove all sides before you begin. NOTE: UPON INSPECTION OF PARTS IF YOU FIND ANY DAMAGE OR MISSING PARTS PLEASE CALL DK2 POWER AT 702-331-5353 OR CONTACT US VIA OUR WEBSITE WWW.DK2POWER.
STEP 2: 1. PREPARE TO INSTALL THE AXLE 2. Slide chipper body to hang off side of the crate as shown. 3. Have a helper tip the unit forward while you complete the next step.
STEP 3: 1. Tip the unit forward 2. Install the axle using the 2 bolts and hardware provided and tighten.
STEP 4: 1. 2. 3. 4. 5. 6. INSTALL THE WHEELS Place 1 black spacer on the axle first Install the wheel, washer, nut and pin. Wheels should spin free. Install end cap Repeat for other wheel.
STEP 5: 1. INSTALL FEED CHUTE 2. With a helper slide the feed chute hinge pins into place, close and latch.
STEP 6 1. Holding the feed chute, lay the unit down as shown 2. Prepare to install the front hitch assembly.
STEP 7 1. Install the front hitch assembly 2.
STEP 8 1. Install the articulated front wheel assembly 2. Use bolt and pin hardware provide and semi tight to allow assembly to raise and lower. 3.
STEP 9 1. Install the TOW BAR 2. Use 2 bolts and hardware provide and secure tightly 3.
STEP 10 1. Install the Lower Chip Chute 2. Carefully remove the mounting hardware from the frame so as to NOT drop into the cutting chamber. 3. You can OPEN the door while removing the hardware to be safe. Then reclose the door to mount the chute. 4. Mount with 4 bolts and hardware provided.
STEP 11 1. INSTALL THE TOP CHIP CHUTE. 2. Use 3 HAND BOLTS and hardware provide and secure tightly 3. PLACE THE NYLON WASHER BETWEEN THE METAL WASHER AND THE CHUTE AS SHOWN.
STEP 12 1. Install the Safety shut-off bar 2. REMOVE THE PACKING NUT FROM THE BOLT AND DISCARD. IT WILL NOT BE NEEDED AND ONLY IS USED TO RETAIN THE MAIN HARDWARE DURING SHIPPING. 3. Install the 2 bolts and bar as shown. 4. Remove nut from spring bolt, 5. Install bar and replace the nut.
STEP 13 1. 2. 3. 4. Install the Battery Use 2 bolts and hardware provide and secure tightly Connect the wiring as shown. Be carefull as to not touch your wrench to metal frame when installing the positive red wire.
REV 1 – 9-19-2019
Ref.No.
READ THE KOHLER ENGINE MANUAL SUPPLIED WITH YOUR UNIT FOR FULL ENGINE OPERATION, SAFETY, AND MAINTENANCE. YOUR UNIT HAS A COMMERCIAL KOHLER ENGINE WITH A 3YR PARTS AND SERVICE WARRANTY. FOR WARRANTY IN YOUR AREA CONTACT THE NEAREST KOHLER DEALER. VISIT WWW.KOHLERENGINES.COM FOR PARTS, SERVICE, MANUALS, AND DEALER LOCATIONS.
OPERATION – BEFORE STARTING ENGINE CLEAR AREA OF ALL PEOPLE AND PROPERTY THAT COULD BE DAMAGED. THINK SAFETY. THIS CHIPPER CAN CAUSE INJURY IF SAFETY IS NOT ENFORCED. ONLY ONE OPERATOR SHOULD WORK THIS UNIT. NEVER HAVE ANOTHER PERSON IN THE AREA OR IN FRONT OF THE CHIP EXIT CHUTE. IF YOUR UNIT WILL NOT START – 1. CHECK THE OIL LEVEL. YOUR ENGINE HAS A LOW OIL SHUTOFF PROTECTION AND WILL NOT START IF LOW ON OIL. 2. MAKE SURE SPARK PLUG WIRE IS SEATED. 3. MOVE THE GAS LEVER ON TO THE RIGHT.
PLEASE DO NOT RETURN TO THE STORE YOU HAVE A 1 YEAR WARRANTY AND DK2 WILL REPLACE A DEFECTIVE PART FOR FREE CALL US AT 702-331-5353 FOR FAST WARRANTY PARTS AND QUESTIONS WHAT IS COVERED DK2 Inc. warrants to the original purchaser of any DK2 product that it will be free and clear of manufacturing defects in workmanship and materials under normal use and service for a period of one (1) year from the date of the original purchase.
