CHIPPER ASSEMBLY GUIDE MODEL: OPC503 3 INCH CHIPPER SHREDDER TOP LOAD DETAIL K2 INC. DK2 POWER USA 4301 S Valley View Blvd STE 10-11 Las Vegas, NV 89103 1-702-331-5353 DETAIL K2, INC. 1080 Clay Avenue Unit 2 Burlington, Ontario, Canada L7L0A1 DK2 USA EAST 6245 Industrial Parkway Whitehouse, OH 43571 PARTS AND SERVICE 702-331-5353 OR WWW.DK2POWER.
STEP 1: Open and unpack all items. Leave lots of working space. Inspect all parts. The Chipper is shipped in a crate. Leave the sides folded down and use as your work space. NOTE: UPON INSPECTION OF PARTS IF YOU FIND ANY DAMAGE OR MISSING PARTS PLEASE CALL DK2 POWER AT 702-331-5353 OR CONTACT US VIA OUR WEBSITE WWW.DK2POWER.
STEP 2: 1. Remove all hardware from chute mounting holes, take care to NOT drop hardware down into the chute opening. 2. Install the chute and the mounting hardware. INSTALL with hardware that is supplied with the chute.
STEP 3: 1. Mount the FEED CHUTE onto the Chipper using supplied bolts and hardware. INSTALL with the nuts and bolts mounted on the unit to assemble the chip chute.
STEP 4 1. INSTALL THE HANDLE USING 4 BOLTS PREINSTALLED ON THE CHUTE FOR THE HANDLE TO BE ASSEMBLED.
STEP 5: 1. INSTALL TOW BAR, SECURE HITCH PIN SPRING LATCH.
STEP 6: READ THE ENGINE MANUAL SUPPLIED WITH YOUR UNIT FOR FULL ENGINE OPERATION, SAFETY, AND MAINTENANCE. 2 1 3 7 4 6 5 1 ON/OFF KEY LOCK 2 GAS – USE MID GRADE OR HIGHER 3 CHOKE – LEFT IS ON / RIGHT IS OFF (RUN POSITION) 4 GAS ON/OFF SWITCH – LEFT IS OFF / RIGHT IS ON 5 THROTTLE – RABBIT FAST / TURTLE SLOW 6 PULL STARTER – PULL TIGHT- THEN PULL START 7 OIL – FILL TO MARK 10W30, WILL NOT START IF OIL IS LOW, HAS LOW OIL SHUTOFF PROTECTION. 2 YELLOW CAPS ARE OIL FILL CAPS.
Your Chipper is equipped with dual REVERSABLE cutting blades. 1. Turn engine key off, remove the key and unplug the spark plug on the engine. 2. Remove the rear cover on the chipper housing 3. Before removing the bolts that mount the blades, place paper towels in the area opening under the blade and the drum housing. This will help to catch bolts from dropping into the bottom of the drum housing. 4. Remove the first bolt. 5.
Part Number Description Part Number. Description. 1 M10*70 bolt 34 gland 2 hitch trailer 35 5/16-24UNF*135 bolt 3 washer⌀10.5*⌀22*2 36 main chipper room 4 spring washer⌀10 37 O-latch⌀8 5 M10locknut 38 tire 6 M8*45 bolt 39 axle 7 washer⌀8.4*⌀20*1.6 40 M8*16 bolt 8 Rubber pad 41 M6locknut 9 support feet 42 spring washer⌀6 10 M8locknut 43 washer⌀6.4*⌀12*1.
OPERATION – BEFORE TURNING KEY AND PULL STARTING ENGINE CLEAR AREA OF ALL PEOPLE AND PROPERTY THAT COULD BE DAMAGED. THINK SAFETY. CHIPS ARE FLYING PROJECTILES AND CAN CAUSE INJURY. WEAR SAFETY GLASSES, HEARING PROTECTION, AND GLOVES DO NOT WEAR LOOSE FITTING CLOTHES THAT COULD GET STUCK IN THE MACHINE MOVING PARTS, ONLY CHIP WOOD, CHILDREN SHOULD NOT RUN THIS EQUIPMENT, STAY ALERT OF YOUR SURROUNDING AND PERSONS THAT COULD APEAR IN THE CHIP PATH WHILE YOU ARE WORKING. UNIT IS DIRECT DRIVE.
QUICK START AND TROUBLE SHOOTING GUIDE QUICK START SETUP • • • • • • ADD 10W30 OIL TO ENGINE ADD GAS PIN BOTH WHEELS INTO PIVOT BRAKE HOLES. TURN KEY ON HALF THROTTLE (CHOKE OPTIONAL FOR COLD STARTS) PULL START THE ENGINE TREE CHIPPING • • • • ENGINE ON HIGHEST SPEED FEED SMALLER TREES INTO CHUTE AND LET GO, TREE WILL AUTO FEED. FEED LARGER TREES SLOWLY ALLOW CUTTER WHEEL TO REGAIN RPM SPEED BETWEEN CUTS. FEED LEAVES, TWIGS AND UPTO 1 INCH DIA TREES INTO TOP HOPPER.
PLEASE DO NOT RETURN TO THE STORE YOU HAVE A 1 YEAR WARRANTY AND DK2 WILL REPLACE A DEFECTIVE PART FOR FREE CALL US AT 702-331-5353 FOR FAST WARRANTY PARTS AND QUESTIONS WHAT IS COVERED DK2 Inc. warrants to the original purchaser of any DK2 product that it will be free and clear of manufacturing defects in workmanship and materials under normal use and service for a period of one (1) year from the date of the original purchase.
