Manual

Section 1 - Safety
ALERT MESSAGES ..............................................................1-1
Section 2 - Introduction
SYSTEM DESCRIPTION ...................................................... 2-1
Communications Loop .................................................. 2-1
LON Communication Heartbeat .................................... 2-2
Theory of Operation ...................................................... 2-2
Controller Logs .............................................................. 2-4
Controller User Logic .................................................... 2-4
Communication Network Fault Operation ..................... 2-4
Multiple Wiring Faults .................................................... 2-5
MAJOR COMPONENT DESCRIPTIONS ............................. 2-5
System Controller .......................................................... 2-5
Local Operating Network (LON) .................................... 2-6
Network Extenders ................................................ 2-6
EQ21xxPS Series Power Supplies and
EQ2100PSM Power Supply Monitor ...................... 2-7
EQP21xxPS(–X) Power Supplies and
EQP2410PS(–P) Converter ...........................................2-7
EQ2220GFM Ground Fault Monitor ......................................2-7
Field Devices ................................................................. 2-7
Flame Detectors .................................................... 2-7
EQ3730EDIO Enhanced Discrete I/O Module ....... 2-8
EQ3700 8 Channel DCIO Module ......................... 2-8
EQ3720 8 Channel Relay Module ......................... 2-9
EQ3710AIM Analog Input Module ......................... 2-9
EQ3740IPM Intelligent Protection Module ........... 2-10
EQ3750ASH Addressable Smoke & Heat Module .. 2-10
EQ25xxARM Agent Release Module ....................2-11
EQ25xxSAM Signal Audible Module .................... 2-12
EQ22xxIDC Series Initiating Device Circuit ......... 2-12
EQ22xxDCU / EQ22xxDCUEX Digital
Communication Units ................................... 2-13
PIRECL PointWatch Eclipse ................................ 2-13
OPECL Open Path Eclipse .................................. 2-13
UD10 DCU Emulator ........................................... 2-13
Section 3 - Installation
SAFETY SYSTEM DESIGN REQUIREMENTS .................... 3-1
Identifying the Area of Protection .................................. 3-1
Identifying Wiring, Network (LON), and System Power
Requirements ........................................................ 3-1
General Wiring Requirements................................ 3-1
Power Wiring .......................................................... 3-1
System Wiring (ATEX and IECEx) ......................... 3-1
Determining Power Requirements ......................... 3-3
EQ211xPS, EQ213xPS and EQ217xPS Power
Supplies ......................................................... 3-5
Backup Battery ...................................................... 3-5
Battery Charger ..................................................... 3-5
EQP21x0PS(–X) Power Supplies .......................... 3-6
EQP2410PS(–P) Converter ................................... 3-6
Determining Power Requirements ......................... 3-7
Shield Grounding ................................................... 3-8
Junction Box Grounding ........................................ 3-8
Response Time vs. System Size ............................ 3-8
Moisture Damage Protection ................................. 3-8
Electrostatic Discharge .......................................... 3-8
GROUND FAULT MONITOR (GFM) INSTALLATION ........... 3-8
Mounting ................................................................ 3-8
Wiring .................................................................... 3-8
NETWORK AND NETWORK EXTENDER INSTALLATION ......3-9
Mounting ................................................................ 3-9
Wiring .................................................................... 3-9
INITIATING DEVICE CIRCUIT (IDC) INSTALLATION .........3-11
EQ22xxIDC Series Initiating Device Circuit ....................... 3-11
Mounting ............................................................... 3-11
Wiring ...................................................................3-11
EQ22xxIDCGF Series Initiating Device Circuit Ground
Fault ..................................................................... 3-12
Mounting .............................................................. 3-12
Wiring .................................................................. 3-12
EQ22xxIDCSC Series Initiating Device Circuit Short
Circuit .................................................................. 3-13
Mounting .............................................................. 3-13
Wiring .................................................................. 3-13
Table of Contents