Instruction Manual

ManualsBrandsDet-Tronics ManualsEquipmentEQ3750ASH EQP Addressable Smoke & Heat (ASH) Module

INSTRUCTIONS

Eagle Quantum Premier

(EQP)

Addressable Smoke & Heat (ASH) Module

EQ3750ASH

4.2 ©Detector Electronics Corporation 2012 Rev: 12/12 95-8654

Description

The Eagle Quantum Premier

(EQP) Addressable

Smoke and Heat (ASH) Module is designed to expand

the input and output capability of Detector Electronics

Corporation’s (Det-Tronics

) EQP system.

The ASH is an interface device designed to provide

continuous and automated ﬁre protection. It ensures

system operation through supervision of system inputs/

outputs and Local Operating Network/Signaling Line

Circuit (LON/SLC) monitoring in the Controller.

The ASH is located directly on the LON of the EQP system,

with a loop of up to 64 addressable devices tied into the

ASH. This allows the EQP Controller to annunciate a ﬁre

alarm from either its own LON based I/O or from the ASH

connected addressable detection loops.

System status can be determined using the Eagle

Quantum Safety System Software (S

), and the status

indicators on the module.

Features anD BeneFits

• Expands the capabilities of Det-Tronics’ Eagle

Quantum Premier system

• EQP Controller can support up to 10 ASH Modules

on a loop

NOTE

This support is dependant on system conguration

and logic within S

• Provides power and communications to 64

addressable devices

• Utilizes Apollo Discovery devices

• ASH Module alarm and fault conditions are logged in

the EQP Controller

• LEDs for easy annunciation of power, faults and

active devices on the loop

• Monitors single addressable devices

• Provides remote I/O capabilities via LON/SLC.

• DIN Rail or Panel mounting

• Plug-in wiring connectors

• RFI and EMI hardened

• Approved for use in Marine applications (Panel

mount only).

Summary of content (8 pages)

PAGE 1
INSTRUCTIONS Eagle Quantum Premier ® (EQP) Addressable Smoke & Heat (ASH) Module EQ3750ASH Description The Eagle Quantum Premier® (EQP) Addressable Smoke and Heat (ASH) Module is designed to expand the input and output capability of Detector Electronics Corporation’s (Det-Tronics®) EQP system. The ASH is an interface device designed to provide continuous and automated fire protection.
PAGE 2
Theory Of Operation ISOLATORS Isolators are used to disconnect a shorted section of the ASH Module Apollo loop so that the remaining sections can continue to operate. In accordance with the NFPA 72 standard for SLCs, the ASH Module supports Class A, Class B, and Class X SLC wiring styles. During normal operation, the ASH Module continuously checks the loop for alarm and fault conditions and executes user defined programmed logic that coordinates the control of the field devices.
PAGE 3
Class X is intended for use in a multi-zone system and requires that the first isolator on each leg be installed next to the ASH Module, within the same enclosure. In addition, an isolator is needed between each zone as illustrated in Figure 4. Alarm receipt capabilities in the other zones shall be maintained during a single open, single ground, wire-to-wire short, or open and ground. STATUS INDICATOR LEDs ZONE 2 NODE 2 NODE 3... ISOLATOR ..................... ISOLATOR ASH MODULE ................. .
PAGE 4
Table 3—List of Supported Devices APOLLO SPEC SHEET PP2052 PP2052 PP2052 PP2052 PP2052 PP2092 PP2094 PP2084 PP2052 PP2052 PP2267 PP2267 PP2156 PP2267 PP2390 PP2390 PP2390 PP2390 39117-468 PP2390 PP2390 PP2390 DET-TRONICS Part nUmber 000515-501 000515-502 000515-503 000515-504 000515-505 000515-509 000515-510 000515-511 000515-512 000515-513 000515-515 000515-516 000515-517 000515-518 000515-551 000515-552 000515-553 000515-554 000515-557 000515-559 000515-560 000515-561 Apollo Part nUmber 58000-500 58000-
PAGE 5
Specifications Passive and Active Integrity Checks During a passive integrity check no alerts will be sent to the ASH Module or EQP Controller. All indications will be handled by the local LEDs on the loop devices. INPUT VOLTAGE— 24 Vdc nominal, 18 to 30 Vdc. INPUT Current (Maximum)— 690 mA. An active integrity check will be indicated on the ASH Module, the controller, and the loop devices as an active alarm. A fault indication will be generated if the integrity check fails.
PAGE 6
Certification — FM / CSA: Class I, Div. 2, Groups A, B, C, D (T4). Class I, Zone 2, Group IIC (T4). FM EQ3750ASH APPROVED P1 ATEX: Compliance with: II 3 G Ex nA nC IIC T4 Gc DEMKO 10 ATEX 150744X Tamb = –40°C to +85°C. – 2 – + 3 + SHLD* SHLD 4 – 5 – + 6 + 24 VDC INPUT VOLTAGE 24 VDC INPUT VOLTAGE POWER SHLD COM 1 SHLD 7 EN 60079-0:2012 EN 60079-15:2010.
PAGE 7
Day mode Start / Stop time The day/night mode is enabled simply by setting the day response mode to a different value than the night response mode. The start and stop times are then set according to the desired switchover time. At the start time, the response mode is set to the “Day Mode Start Time” setting. At the stop time, the response mode is set to the “Day Mode Stop Time” setting.
PAGE 8
Maintenance ORDERING INFORMATION To ensure reliable protection, it is important to check the ASH Module on a regularly scheduled basis. The frequency of checks is determined by the requirements of the particular installation. When ordering, please specify: EQ3750ASH Addressable Smoke and Heat Module Refer to the ASH Module Model Matrix for details. REPLACEMENT PARTS MODEL DESCRIPTION The ASH Module is not designed to be repaired in the field.