Instructions / Assembly

ManualsBrandsDESwan ManualsFire Pit Kits45,000 BTU 43.3 in. x 29.1 in. Rectangle Steel Base Gas Fire Pit Table in Wicker Finish

WARNING: If the information in this manual is not followed

exactly, a fire or explosion may result causing property damage,personal injury, or loss of life.

Failure to follow these instructions could result in fire or

explosion, which could cause property damage, personal

injury or death.

CARBON MONOXIDE HAZARD

This appliance can produce carbon

monoxide which has no odor .

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed

space such as a camper, tent, car or home

WARNING

Do not store or use gasoline, or other flammable vapors

and liquids, in the vicinity of this or any other appliance.

An LP-cylinder not connected for use shall not be stored

in the vicinity of this or any other appliance.

DANGER

FIRE OR EXPLOSION HAZARD

If you smell gas:

Shut off gas to the appliance .

Extinguish any open flame.

If odor continues, leave the area immediately.

After leaving the area, call your gas supplier or fire

department.

WARNING: For Outdoor Use Only

WARNING

: Failure to posi�on the parts in accordance with these diagrams or failure to use only

parts speciﬁcally approved with this appliance may result in property damage or personal injury.

Installation and service must be performed by a qualified

installer, service agency, or the gas supplier.

DANGER

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Save these instructions for future use. If

you are assembling this unit for someone

else, give this manual to him or her to read

and save for the future.

Item#

Model#

785.0310.000.001

Summary of content (15 pages)

PAGE 1
DANGER FIRE OR EXPLOSION HAZARD If you smell gas: Item# Model# 785.0310.000.001 Shut off gas to the appliance . Extinguish any open flame. If odor continues, leave the area immediately. After leaving the area, call your gas supplier or fire department. Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury or death.
PAGE 2
IMPORTANT SAFETY INFORMATION Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so may result in a fire, explosion, injury or death. WARNING  The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSIZ223.1/NEPA54, OR CAN/CGA-B149.1, National Gas and Propane Installation Code.
PAGE 3
 Combustible material should not be within 72 inches of the top of the unit, or within 48 inches around the entire unit.  Keep the appliance area clear and free from combustible material, gasoline and other flammable vapors and liquids.  If the flame goes out while burning, turn the gas valve off. Wait 5 minutes before repeating the initial lighting procedure. Once you have a flame started, hold down the control knob for 1 minute.  Do not add water into the unit.
PAGE 4
NOTE:You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned "OFF" before assembling.Do NOT attempt to assemble without proper tools. Min. Clearance 48 in.(121.9cm) Min. Clearance 48 in.(121.9cm) Combustible materials should not be within 72 inches of the top of the unit, or within 48 inches around the entire unit. Min. Clearance 48 in.(121.9cm) Min. Clearance 48 in.(121.9cm) Before beginning assembly of this product be sure all parts are present.
PAGE 5
PARTS IDENTIFICATION LIST A B I L K C J O M N F H E D G Ceramic Tile Item Description Qty Item Description Qty A Burner Lid 1 I Ceramic Tile 2 B Table Top 1 J Fire Pit 1 C Side Panel 1 K Guard 1 D Front Panel 1 L Burner 1 E Metal Stand 1 M Ignition 1 F Back Panel 1 N Control Knob 1 G Door 1 O Ceramic Tile 2 H Profile Tube 1 5
PAGE 6
FIRE PIT ASSEMBLY INSTRUCTIONS 1.Check that the control knob ( N ) for the gas supply system is turned to the “OFF” position before starting any assembly. OFF LOW HIGH N 2. Attach the side panel ( C ) and the door ( G ) to the table top ( B ) using four M6 x 15 screws ( BB ), four washers ( EE ) , four screw caps (AA).
PAGE 7
3. Attach the back panel ( F ) and front panel ( D ) to the door ( G ) and the side panel ( C ) using eight M6 x 30 screws ( DD ), eight washers ( EE ) , eight screw caps (AA). AA DD EE C F D G 4. Attach the metal stand ( E ) to the back panel ( F ) and front panel ( D ) using four M6 x 25 screws ( CC ), four washers ( EE ) , four screw caps (AA).
PAGE 8
5. Attach the profile tube ( H ) to the the back panel ( F ) and front panel ( D ) using two M6 x 15 screws ( BB ), two washers ( EE ) , two screw caps (AA). F AA BB EE H D 6. Place the ceramic tiles ( I ) and the ceramic tiles ( O ) inside the table top( B).
PAGE 9
7. Attach hose of regulator tightly to bracket. 8.Turn the cylinder valve on the tank clockwise to close the propane tank. Attach the pre-assembled regulator from the table top ( B ) to the cylinder valve by turning the regulator coupling nut clockwise. Make sure it is fastened securely and tighten connections by hand only.
PAGE 10
9. Place propane gas tank ( not included ) into the metal stand ( E ).Make sure the gas tank sits on the metal stand ( E ) completely. Turn the preassembled wing screw on the outer part of metal stand ( E ) clockwise to secure the propane gas tank tightly. 10. Remove the rubber cap on the electronic igniter ( M ) by unscrewing and slide battery into the battery slot. Make sure the positive side of the battery faces outwards. Screw the electronic igniter cap ( M ) over the battery tightly.
PAGE 11
.Pour the lava rocks ( not included ) into the fire pit ( J ). L CAUTION To ensure proper function, the guard ( K ) on this burner ( L ) should be free of lava rocks at all time . 12. Put burner lid ( A ) onto the fire bowl. A NOTE: When the ﬁre pit is NOT in use or a�er use, when the ﬁre pit has cooled COMPLETELY, cover it with the Burner Cover. DO NOT PUT THE BURNER COVER ON A HOT FIRE PIT.
PAGE 12
OPERATION Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the "off" position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles occur on any connection there may be a leak. If you smell gas or a leak is discovered turn the gas valve off, disconnect propane gas tank and do not use the appliance until the leak is repaired.
PAGE 13
TO TURN ON THE FIRE PIT 1.Push and slowly turn the control knob to the HIGH position 2. Hold ignitor to light the burner, release control knob after 45 seconds. 3. Observe the flame height when lit. Flame should be 3 to 13 inches high. 4. If the flame goes out, turn off the burner and wait approximately five minutes to clear out any gas, and repeat steps 1-3 above. 5. If your burner fails to light again, turn the control knob to the off position and contact your dealer or gas supplier. 6.
PAGE 14
TROUBLESHOOTING Problem Cause Igniter pin and burner are wet Igniter battery is incorrectly inserted Heating unit won't light Igniter pin is broken Electrode wire is loose or disconnected Electrode wire is shorting between valve and igniter pin Regulator isn't connected securely to the tank Heating unit emits a lot of black smoke Reconnect wire to the igniter box located inside the table behind the igniter box Manufacturing for a replacement part Tighten regulator connection to the gas tank Check all
PAGE 15
WARRANTY The manufacturer warranty will be voided by, and manufacturer disclaims any responsibility for, the following actions:  Modification of the unit and/or components including the gas valve assembly.  Use of any component part not manufactured or approved by LETRIGHT Manufacturing.  Use and installation other than what is listed in this manual. Please contact the manufacturer for replacement parts.