Open Cabinet Assembly Instructions SKU Reference # Finish 211-4572 211-4573 211-4574 211-4673 4040 4097 4057 14596 White Java Cottage Charcaol Tools Needed: hammer screwdriver 01-13966-00 11/20
SAFETY PRECAUTIONS WARNING • This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or serious injury could occur. • Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur. • Do not overload unit.
HARDWARE (H1) x 14 cam post (H2) x 14 cam lock (H3) x 8 shelf pin (H4) x 6 wide dowel 8 mm x 30 mm (H6) x 20 small nail (H7) x 4 nail-on foot (H8) x 4 cover cap (H9) x 2 back anchor (H10) x 1 small screw #8 x 1/2 in. (H11) x 1 nylon zip tie (H12) x 1 long screw #8 x 1-1/2 in. (H13) x 2 stacking bracket (H14) x 8 medium screw #8 x 7/8 in.
DESCRIPTION QUANTITY A B C D E F G H left side panel right side panel back cleat bottom shelf top shelf back panel trim adjustable shelf 1 1 1 1 1 1 2 2 E G C F H A B H finished edge unfinished edge Unfinished edges are shaded in gray in the illustrations throughout this document. It is important to understand how finished edges go together. Take a moment to lay out all the wood pieces and note the finished and unfinished (raw wood) edges.
STEP 1 (H2) B (H1) (H4) (H1) x 6 cam post (H2) x 4 cam lock A (H4) x 4 wide dowel 8 mm x 30 mm 1. Secure cam posts (H1) into holes as shown. PLEASE NOTE: Cam post is secure when threads on screw are not showing. 2. Insert cam lock (H2) and press to bottom of hole. Ensure arrow on cam lock is pointing towards outer edge as shown. 3. Insert dowels (H4) into holes as shown.
STEP 2 (H1) (H4) E D (H2) C (H1) x 4 cam post (H2) x 10 cam lock (H4) x 2 wide dowel 8 mm x 30 mm 1. Secure cam posts (H1) into holes as shown. PLEASE NOTE: Cam post is secure when threads on screw are not showing. 2. Insert cam lock (H2) and press to bottom of hole. Ensure arrow on cam lock is pointing towards outer edge as shown. 3. Insert dowels (H4) into outer holes of top shelf (E) as shown.
STEP 3 C B D 1. Align side panel (B) with appropriate holes in bottom shelf (D) and back cleat (C) as shown and install. 2. Tighten cam locks to secure side panel (B) to back cleat (C) and bottom shelf (D).
STEP 4 C A D 1. Align side panel (A) with appropriate holes in bottom shelf (D) and back cleat (C) as shown and install. 2. Tighten cam locks to secure side panel (A) to back cleat (C) and bottom shelf (D).
STEP 5 E B A 1. Align top shelf (E) with appropriate holes as shown and install. 2. Tighten cam locks to secure side panels (A & B) to top shelf.
STEP 6 G (H6) x 20 small nail (H7) x 4 nail-on foot 1. Place back panel (G) onto unit (making sure the finished side of backer faces down) and center horizontally and vertically. 2. Nail the back panel (G) into position using small nails (H6). Avoid angling nails. 3. Gently tap the nail-on feet (H7) approximately 1 in. away from each corner. (Note: If stacking this unit, skip this step.
STEP 7 G G G G NOTE: Thicker edges of trim should be positioned towards the top and bottom ends of the unit unless stacking, then choose either option 1 or 2 for the adjoining trim preference. option 1 option 2 (H1) x 4 cam post 1. Secure cam posts (H1) into holes as shown. PLEASE NOTE: Cam post is secure when threads on screw are not showing. 2. Flip the unit over so the open side is facing up. 3. Align the cam posts in the trim with the appropriate holes as shown and install.
STEP 8 H H (H3) x 8 shelf pin 1. Push shelf pins (H3) into holes at desired locations. 2. Slide adjustable shelves (H) into frame at a slight angle and position onto shelf pins (H3).
STEP 9 WALL (H11) (H12) (H10) (H9) (H9) (H8) x 4 cover cap 1. 2. 3. 4. (H9) x 2 back anchor (H10) x 1 small screw #8 x 1/2 in. (H11) x 1 nylon zip tie (H12) x 1 long screw #8 x 1-1/2 in. Install four cam cover caps (H8) by pressing them into the cam locks as shown. Use 1/2 in. screw (H10) to secure back anchor (H9) to top shelf. Place back anchor (H9) against wall stud as shown. Use 1-1/2 in. screw (H12) to secure back anchor to wall. Secure plastic tie (H11) to prevent unit from tipping.
STEP 10 (H13) x 2 stacking bracket 1. 2. 3. 4. 14 (H14) x 8 medium screw #8 x 7/8 in. NOTE: If stacking this unit, align the units on top of each other as shown. Install stacking brackets (H13) to the back side of the units using the stacking screws (H14). Be sure to center the bracket to the side panels before screwing them in. NOTE: Each unit should be individually secured to the wall using the provided hardware.
