4 Drawer Base Cabinet Assembly Instructions 4039 / 4056 / 4094 Tools Needed: 01-19062 2/18
SAFETY PRECAUTIONS WARNING • This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or serious injury could occur. • Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur. • Do not overload unit.
HELPFUL HINTS We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc. finished edge unfinished edge Unfinished edges are shaded in gray. It is important to understand how finished edges go together. Take a moment to lay out all the wood pieces and note the finished and unfinished (raw wood) edges. Arrange pieces so all finished edges are facing the same way.
HARDWARE (H1) x 22 cam post (H7) x 4 nail-on foot (H2) x 14 15mm cam lock (H8) x 4 cover cap (H12) x 1 long screw #8 x 1-1/2 in. (H13) x 2 stacking bracket (H17) x 8 12mm cam lock (H18) x 8 dowel 6mm x 30mm (H3) x 16 funnel screw (H4) x 6 wide dowel 8mm x 30mm (H5) x 32 euro screw (H9) x 2 back anchor (H10) x 1 small screw #8 x 1/2 in. (H11) x 1 nylon zip tie (H14) x 8 medium screw #8 x 7/8 in. Just call 1-800-874-0008 for parts and service.
DESCRIPTION QUANTITY E A left side panel 1 B right side panel 1 C back cleat 1 D bottom shelf 1 E top shelf 1 F back panel 1 G trim 2 G C F H right drawer side 4 I drawer back 4 J left drawer side 4 K drawer bottom 4 L drawer front 4 A B I J K L H G D X4 5
STEP 1 (H2) B (H1) (H1) x 6 cam post 1. 2. 3. 6 (H2) x 4 15mm cam lock (H4) A (H4) x 4 wide dowel 8mm x 30mm Secure cam posts (H1) into holes as shown. PLEASE NOTE: Cam post is secure when threads on screw are not showing. Insert cam lock (H2) and press to bottom of hole. Ensure arrow on cam lock is pointing towards outer edge as shown. Insert dowels (H4) into holes as shown.
STEP 2 (H1) (H4) E D (H2) C (H1) x 4 cam post 1. 2. 3. (H2) x 10 15mm cam lock (H4) x 2 wide dowel 8mm x 30mm Secure cam posts (H1) into holes as shown. PLEASE NOTE: Cam post is secure when threads on screw are not showing. Insert cam lock (H2) and press to bottom of hole. Ensure arrow on cam lock is pointing towards outer edge as shown. Insert dowels (H4) into outer holes of top shelf (E) as shown.
STEP 3 C B D 1. 2. 8 Align side panel (B) with appropriate holes in bottom shelf (D) and back cleat (C) as shown and install. Tighten cam locks to secure side panel (B) to back cleat (C) and bottom shelf (D).
STEP 4 C A D 1. 2. Align side panel (A) with appropriate holes in bottom shelf (D) and back cleat (C) as shown and install. Tighten cam locks to secure side panel (A) to back cleat (C) and bottom shelf (D).
STEP 5 E B A 1. 2. 10 Align top shelf (E) with appropriate holes as shown and install. Tighten cam locks to secure side panels (A & B) to top shelf.
STEP 6 G (H6) x 20 small nail 1. 2. 3. (H7) x 4 nail-on foot Place back panel (G) onto unit (making sure the finished side of backer faces down) and center horizontally and vertically. Nail the back panel (G) into position using small nails (H6). Avoid angling nails. Gently tap the nail-on feet (H7) approximately 1 in. away from each corner.
STEP 7 G G G G NOTE: Thicker edges of trim should be positioned towards the top and bottom ends of the unit unless stacking, then choose either option 1 or 2 for the adjoining trim preference. option 1 option 2 (H1) x 4 cam post 1. 2. 3. 12 Secure cam posts (H1) into holes as shown. PLEASE NOTE: Cam post is secure when threads on screw are not showing. Flip the unit over so the open side is facing up. Align the cam posts in the trim with the appropriate holes as shown and install.
STEP 8 J (H17) (H17) H H K J (H3) I (H1) L (H18) L (H15) (H5) (H1) x 8 cam post 1. 2. 3. 4. 5. 6. 7. (H17) x 8 12mm cam lock (H18) x 8 dowel 6mm x 30mm (H15) x 4 inside drawer glide (H5) x 16 euro screw (H3) x 16 funnel screw Insert cam lock (H17) into drawer sides and press to bottom of hole. Ensure arrow on cam lock is pointing towards outer edge as shown. Secure drawer sides (H & J) to drawer back (I) using funnel screws (H3).
STEP 9 (H16) x 4 outside drawer glide 1. 2. 14 (H5) x 16 euro screw Secure the outside drawer glides (H16) to the assembled cabinet as shown using four euro screws (H5). Repeat for the remaining glides Insert the four assembled drawers into the cabinet as shown.
STEP 10 WALL (H11) (H9) (H8) x 4 cover cap 1. 2. 3. 4. (H12) (H9) (H10) (H9) x 2 back anchor (H10) x 1 small screw #8 x 1/2 in. (H11) x 1 nylon zip tie (H12) x 1 long screw #8 x 1-1/2 in. Install four cam cover caps (H8) by pressing them into the cam locks as shown Use 1/2 in. screw (H10) to secure back anchor (H9) to top shelf. Place back anchor (H9) against wall stud as shown. Use 1-1/2” screw (H12) to secure back anchor to wall. Secure plastic tie (H11) to prevent unit from tipping.
STEP 11 The 4 drawer cabinet is intended to be a base cabinet only. It should not be on top when stacked. (H13) x 2 stacking bracket 1. 2. 3. 4. 16 (H14) x 8 medium screw #8 x 7/8 in. NOTE: If stacking this unit, align the units on top of each other as shown. Install stacking brackets (H13) to the back side of the units using the stacking screws (H14). Be sure to center the bracket to the side panels before screwing them in.
