8-Cube Organizer Assembly Instructions 3628 / 3629 / 3631 Tools Needed: Optional Assembly 01- 3640 7/17
SAFETY PRECAUTIONS WARNING • This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or serious injury could occur. • Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur. • Do not overload unit.
HELPFUL HINTS We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc. finished edge unfinished edge Unfinished edges are shaded in gray. It is important to understand how finished edges go together. Take a moment to lay out all the wood pieces and note the finished and unfinished (raw wood) edges. Arrange pieces so all finished edges are facing the same way.
HARDWARE DESCRIPTION (H1) x 6 long dowel A side panel 2 B top/bottom panel 2 C horizontal divider 1 D vertical divider 6 E back panel 4 (H2) x 14 short dowel (H3) x 18 screw cover QUANTITY B (H4) x 18 assembly screw #5mm x 38mm (H5) x 48 nail (H6) x 1 L-bracket E D E D D A C E E (H7) x 1 L-bracket screw #10 x 1/2' flathead (H8) x 1 wall screw #10 x 1-1/2” (H9) x 2 hole plug Just call 1-800-874-0008 for parts and service.
STEP 1 B (H2) x 6 short dowel 1. Insert six dowels (H2) into one top/bottom panel (B). Nine hole side facing up.
STEP 2 A B (H4) x 2 assembly screw #5mm x 38mm 1. 6 Attach side panel (A) with two screws (H4) to top/bottom panel (B) with screwdriver. Finished edges of unit facing up.
STEP 3 D D B D (H4) x 3 assembly screw #5mm x 38mm 1. 2. Insert three vertical dividers (D) onto dowels in top/bottom shelf (B). From opposite side of fixed shelf, secure each vertical divider with a screw (H4). Make sure finished edges are facing up.
STEP 4 (H1) x 6 long dowel 1. 2. 3. 4. 8 (H4) x 2 assembly screw #5mm x 38mm Push six long dowels (H1) into vertical dividers. Push horizontal divider (C) down over dowels. (Holes in horizontal dividers go all the way through.) Secure horizontal divider with two screws (H4) through side panel. Ensure finished edge is facing to the front as illustrated.
STEP 5 D D D (H2) x 6 short dowel 1. 2. 3. Insert three vertical dividers (D) onto existing dowels in horizontal divider (C). Push six short dowels (H2) into vertical dividers as illustrated. Ensure the finished edges are facing to the front.
STEP 6 A (H4) x 11 assembly screw #5mm x 38mm B 1. 2. 3. 4. 10 Align dowels to holes in underside of top panel (B), and place into position. Secure with two screws (H4) through side panel. Secure top vertical dividers with 3 screws (H4) through top panel. Attach other side panel (A) with six screws (H4) as shown.
STEP 7 E E E E for stacking (H3) x 18 screw cover 1. 2. 3. 4. 5. (H5) x 48 nail (H2) x 2 short dowel (H9) x 2 hole plug or for single unit or Lay unit so finished (front) edges face down (unfinished edges will face up). Push screw covers (H3) onto all screw heads. Position the back panels (E) in a staggered patten as shown. Nail (H5) the back panels (E) into place, being careful to not angle the nails. For single unit: Insert hole plugs (H9) into top holes.
STEP 8 Optional vertical mounting: Single unit only; can not stack. wall stud B B top panel Top panel (H6) x 1 L-bracket (H7) x 1 L-bracket screw #10 x 1/2' flathead (H8) x 1 wall screw #10 x 1-1/2” Wall stud Stacking - horizontal mounting only! Mount L-bracket through an open cube which doesn’t have a back panel. 1. Align unit with wall stud. 2. Place short end of L-bracket (H6) against wall/wall stud. Uses 1-1/2” screw (H8) to secure L-bracket to wall stud. 3.
