User's Manual

12
Using the Settings menuDX-WBRDVD1
4 Press or to select Auto or Off. If Deep Color is set to Auto,
and the player is connected to TV via HDMI cable, the player first
tries to set the color depth to 36 bits, if the 36 bits is not
supported by the TV, it tries to set the color depth to 30 bits, if the
30 bits is not supported by the TV, the player sets the color depth
to 24 bits. If Deep Color is set to Off, the player sets the color
depth to 24 bits.
5 Press to go to the previous menu.
Changing the Audio settings
Selecting the PCM downsampling rate
If your player is connected to an audio receiver or TV with an optical or
coaxial cable, select the highest PCM sampling rate the amplifier
supports.
To select the PCM downsampling rate:
1 Press ENTER. The Settings menu opens.
2 Press or to select Audio, then press ENTER. The Audio menu
opens.
3 Press or to select PCM Downsampling, then press ENTER.
4 Press or one or more times to select the PCM downsampling
rate you want. You can select 48KHz, 96KHz, or Off.
If you do not have a surround sound receiver connected to your
player through one of the digital audio jacks (optical or coaxial),
select 48kHz. Otherwise, select the highest sampling rate the
receiver supports. See the documentation that came with the
receiver.
Note:
Setting the coaxial audio output’s PCM downsampling sampling
rate too high may result in unpredictable audio playback. If you are
not sure, set the rate to 48kHz.
5 Press to go to the previous menu.
Selecting the digital audio output mode
To select the digital audio output mode:
1 Press ENTER. The Settings menu opens.
2 Press or to select Audio, then press ENTER. The Audio menu
opens.
3 Press or to select Digital Output, then press ENTER.
4 Press or to select the digital output mode you want, then
press ENTER. You can select:
• PCM—Sends a PCM audio signal of up to 7.1 channels over
the HDMI connection and up to 5.1 channels over the coaxial
or optical connection.
• Bitstream HD—Lets your player send Dolby TrueHD or
DTS-MA bitstreams over HDMI (if your player is connected to
a compatible HDMI audio receiver). If your player is not
connected to a compatible HDMI receiver (for example, your
player is connected directly to the TV or your player is
connected to an audio receiver using an optical or coaxial
cable), a compatible audio signal is automatically sent over
the HDMI and optical or coaxial connections.
With this setting, Blu-ray audio is limited to the soundtrack
for the main movie (no PIP audio).
• Bitstream Legacy—Sends a DTS or Dolby Digital
bitstream from the disc over the HDMI and optical or coaxial
connections. Blu-ray audio is limited to the soundtrack for
the main movie (no PIP audio).
• Bitstream mixed—Sends a mixed (PIP audio and movie
audio) DTS audio stream over the HDMI and coaxial or optical
connections. This mode is primarily intended for use when
you want to hear both PIP audio and the movie audio.
5 Press to go to the previous menu.
Turning dynamic range control on or off
Dynamic range control is only active when a Dolby Digital signal is
detected.
When Dynamic Range Control is set to Off, movie soundtracks are
played with the standard dynamic range.
When movie soundtracks are played at low volume or from smaller
speakers, you can set Dynamic Range Control to On. Your player
applies appropriate compression to make low-level content more
intelligible and prevent dramatic passages from getting too loud.
When Dynamic Range Control is set to Auto, the system turns on the
Dynamic range control for all BD movie soundtracks except Dolby
TruHD. If you have selected a Dolby TruHD track on the BD disc, Auto tells
the BD player to only turn on dynamic range control if information
embedded in the Dolby TruHD sound track tells it to do so.
To turn dynamic range control on or off:
1 Press ENTER. The Settings menu opens.
2 Press or to select Audio, then press ENTER. The Audio menu
opens.
3 Press or to select Dynamic Range Control, then press
ENTER.
4 Press or to select Auto or Off.
5 Press to go to the previous menu.
Selecting the stereo downmix
To select the stereo downmix:
1 Press ENTER. The Settings menu opens.
Settings
Parental
Display
Audio
Network
Audio
Language
PCM Downsampling
Digital Output
Dynamic Range Control
Stereo Downmix
48 Khz
PCM
Off
Auto
BD-Live
System
Settings
Audio
Network
Display
Display
HDMI Status
HDMI preferred Format
Resolution
TV Aspect
Film Mode(1080p24)
Deep Color
Connected
1080P
HDMI Auto
16:9 Wide
Off
Off
System
Language
BD-Live
Parental
Settings
Audio
Network
Display
Display
HDMI Status
HDMI preferred Format
Resolution
TV Aspect
Film Mode(1080p24)
Deep Color
Connected
1080P
HDMI Auto
16:9 Wide
Off
Off
System
Language
BD-Live
Parental
Settings
Audio
Network
Display
Display
HDMI Status
HDMI preferred Format
Resolution
TV Aspect
Film Mode(1080p24)
Deep Color
Connected
1080P
HDMI Auto
16:9 Wide
Off
Off
System
Language
BD-Live
Parental