OWNER'S OPERATION AND INSTALLATION MANUAL UNVENTED (VENT-FREE) Gas Compact Classic Hearth Dual Burner Fireplace VDCFTNA,VDCFTPA,VDCFRPA,VDCFRNA

www.desatech.com
113133-01C14
INSTALLATION
Continued
3
2
1
O
F
F
P
I
L
O
T
O
N
H
I
L
O
Figure 16 - Installing Blower Bracket
Assembly (Remote-Ready Unit Shown)
Wire
Harness
Blower
Bracket
Assembly
Screw
Wire
Harness
Switch
Wiring Routing
Hole in Bafe
Switch
Plate
Remote/
Blower
Bracket
Power
Cord
Lower Louver Door
Blower
Mounting
Holes
Figure 17 - Wiring Diagram For Blower
Accessory Standard Installation
Red
Red
Fan Switch
(Auto/Off/On)
Blue
Blue
Thermostat
Switch
(N.O.)
Green
White
Green
White
On
110/115
V.A.C.
Blower
Motor
Black
Off
1
2
3
Auto
2. Remove 4 screws from upper louver (see
Figure 15). Save these screws.
3. Pull upper louver straight out from the cabinet. Be
careful not to scratch the paint. Set louver aside.
4. Open lower louver door by swinging door
down (see Figure 15).
6. Route the wire harness through the hole in left
side of bafe and between rebox wrapper and
outer casing.
7. Insert the 4 wire harnesses from behind the
remote/blower bracket through hole in rear of
bracket with bushing and through the left rectan-
gular hole to front of replace (see Figure 16).
8. Reconnect red wire to switch position 3.
Reconnect blue wire to switch position 1.
Reconnect green and white wires.
9. Install the switch plate on the remote/blower
bracket with 2 #10 screws provided (see Fig-
ure 18, page 15). Route power cord out of the
cabinet by inserting it through the bushing on
the outer casing (see Figure 16). Plug fan kit
into 120-Volt grounded power supply and test
operation. Note: When switch is in the AUTO
position, the fan will start after the replace has
run for a few moments. The fan will continue
to run for several moments after the replace
has been turned off. When switch is in the ON
position, the fan will run until turned to OFF.
10. Reinstall upper louver beginning with bottom
screws (see Figure 15). Close lower louver door.
Figure 15 - Removing Top Louver and
Opening Bottom Louver
O
F
F
P
I
L
O
T
O
N
H
I
L
O
Top
Louver
Lower Louver

CAUTION: Label all wires
prior to disconnection when ser-



-

Note: If you are using a mantel with your replace,
use the following instructions. If your replace is
built-in, see For Built-In Installation, page 15.
1. Install snap bushings found in blower kit into
hole in left side of outer casing and into one of
the holes in rear of remote/blower bracket.
2. Make sure the wire harness is rmly connected to
the terminals on the blower bracket assembly.
3. Note the wire locations on back of AUTO/
OFF/ON switch. The terminals on back of
switch are numbered 1, 2 and 3. Carefully
remove red wire from terminal 3 and blue
wire from terminal 1. Black wire can remain
on middle terminal 2 (see Figure 16).
4. Carefully disconnect green and white wires at
their insulated connectors (see Figure 17).
5. In top of the replace cabinet, locate the four
mounting holes on the outer casing. Align
these four holes with those on the blower
bracket assembly. Attach blower bracket as-
sembly to the outer casing with 4 #10 screws
provided (see Figure 16).