Original User Manual | Version 1 | 01.07.2014 Pedelec Groove 2.0 English Item no.
Inhalt Introduction 3 1 Safety 1.1 General 1.2 Statutory requirements 1.2.1 Requirements for the rider 1.3 Battery 1.4 Charger 1.5 Motor 1.6 Adjustments/maintenance/repair 1.7 Transportation of the Pedelec 1.7.1 The Pedelec and your car 1.7.2 The Pedelec on trains 1.7.3 The Pedelec on aeroplanes 1.8 Cleaning 1.8.1 Battery 1.8.2 Motor 1.8.3 Display 1.8.4 Control unit 1.8.5 Charger 1.9 Riding with luggage 1.9.1 Panniers 1.9.2 Trailers 4 4 4 4 5 6 7 7 7 7 7 8 8 8 8 8 8 9 9 9 9 2 Warranty regulations 2.
Introduction Thank you for choosing the Pedelec Groove 2.0. This Pedelec is equipped with an innovative electric drive that assists you when you are cycling. This will make your trip much more enjoyable if you are riding up hills, carrying loads or riding into the wind. The purpose of this User Manual is to help you get the most out of your Pedelec Groove 2.0 and use it correctly. Structure of the User Manual You will ind information on how to use your Pedelec in Chapter 1 „Safety“Safety”.
1 Safety breakage or failure of safety-relevant components Chapter 12 „Technical data“. Read all the safety information. Failure to observe the instructions can cause electric shock, ire and/or serious injury. The User Manual contains the following symbols that denote dangers or important information. If you wish to make any adjustments to the ride characteristics of your Pedelec, please consult your specialist cycle shop.
the EU in individual cases. Before using your Pedelec abroad, ind out about the applicable legislation in the relevant country. 1.3 Battery The battery contains chemical substances, which could cause dangerous reactions if the safety information given here is not adhered to. Avoid contact with liquid leaking rom a damaged battery. In case of contact, rinse of the liquid with water. In case of eye contact, consult a doctor ater rinsing. Never attempt to repair your battery.
1.4 Charger no longer be used, and you must have it inspected by the dealer. A battery that displays a fault must not be charged any more. Children must be supervised. This will ensure that children do not play with the charger. The battery must not be let unattended while charging.
1.6 Condensation may form on the charger if the temperature changes suddenly rom cold to hot. In case of condensation, wait approximately one hour before connecting the charger to the mains, until it has warmed up to the temperature of the room. Ideally, avoid such situations by storing the charger in the place where it is operated. Take the battery out before beginning work (e.g. assembly, servicing, etc.) on the Pedelec. There is a risk of injury through accidentally operating the battery switch.
for your bike in advance. As a rule, you may not take bikes with you on German Intercity Express (ICE) trains. 1.7.3 The Pedelec on aeroplanes Your Pedelec is generally subject to the policies of the respective airline concerning bikes. Batteries are subject to dangerous goods legislation. Therefore, they must not be carried on passenger planes – neither in the cargo hold, nor the cabin. Please contact the relevant airline for detailed information. 1.
1.8.5 Charger 1.9.2 Trailers You may use a trailer with your Pedelec Groove 2.0. Always unplug the charger rom the wall socket before cleaning to avoid a short-circuit and physical injury. Make sure that water does not enter the charger when cleaning. 1.9 Riding with luggage Only use trailers that meet the requirements of the road traic licensing regulations in your country (the Road Traic Licensing Regulations (StVZO) in Germany for example). Non-approved trailers can cause accidents.
2 Warranty regulations 2.1 Warranty periods The statutory warranty valid at the time of delivery applies to all models. 2.2 Warranty conditions 2.2.1 Conditions A defect is present under the following conditions: • Manufacturing, material or information error. • The cause of the change in the product is not wear or ageing arising naturally or as a result of its unctions. • The damage was not caused by use of the Pedelec for other than the intended purpose. 2.2.
4 First steps 4.1 Checking the tightening torques Check that all screws and important components are fastened securely and correctly. You will ind a table with important screw connections and the prescribed tightening torques in Chapter 12 „Technical data“ of the “Original User Manual | General” (CD). 4.2 Fitting the pedals It may be that the pedals for your Pedelec have yet to be itted on delivery: The right pedal (marked with an “R”) is screwed clockwise into the right crank arm.
5 Quick start 4. Press the battery button. The battery is ully charged when all the green LEDs on the battery are lit. Pull the plug of the charger out of the charging socket, close the cover and unplug the charger at the wall socket. Charge the battery completely before riding for the irst time. As required by transport law, the battery leaves the factory with an approximately 30% charge. Charge temperature: 0°C to 45°C.
8. Press the battery switch. The red LED inside it lights up. The carrier is only approved for a maximum of 15 kg! 6 Battery Your battery is a lithium-ion battery, the ideal type for this application. One of the main beneits is its low weight combined with a high capacity. Battery switch 9. Press the button to switch the system on. 10. The most recently selected power-assist mode will be button to select the level of indicated. Press the assistance: (slight), (medium) or (strong).
1. Take the charger provided out of its packaging and plug it in at the wall socket (230–240 V). The LED in the charger now lights up green continuously. Unlocking the battery Your Pedelec is supplied with two battery keys. Keep one key in a safe place, and get a copy made of the key if necessary. 2. Grip the battery with one hand and pull it backwards out of the Pedelec. Hold the battery tight to avoid dropping it. Place the battery down on a suitable surface, which should be dry, lat and non-lammable.
6.1.3 Installing the battery 1. Put the battery back in the battery holder. The battery must be switched off before it is pushed into the battery housing. Installing the battery BATTERY CHARGE STATE DISPLAY •••• 4 LEDs light up 100 – 75% ••• 3 LEDs light up 75 – 50% •• 2 LEDs light up 50 – 25% • 1 LED lights up 25 – 0%* * If the battery is empty, it will work again briely following a short period of rejuvenation and will then switch back of. It must now be charged. 2.
• The number of charges Ater 1,100 charging cycles, your battery will still have 60% of its initial capacity, providing it has been well looked ater. This means 6.6 Ah in an 11 Ah battery and 7.2 Ah in a 15.5 Ah battery. A charging cycle is deined as the sum of the individual charges until the battery has been charged to ull capacity once. Make sure that the battery is ully charged before you ride your bike for the irst time or if you have not used it for a while.
NO 11 12 SYMBOL SET MODE 13 FUNCTION BUTTON PUSH a) Switch the ront and rear light on/of b) Change the indication (VEL, ODO, or DST) c) (in the Settings menu) a) 2 seconds b) 1 second c) 1 second a) Change mode b) (in the Settings menu) a) 1 second b) 1 second Switch the system on/of 2 seconds Assist mode MODE ASSISTANCE RECOMMENDATION Assistance up to at most 25 km/h Use for small climbs (bridges etc.).
8.4 VEL (speed), ODO (total kilometres) and DST (trip distance) 8.6 When you switch the Groove 2.0 on, the display automatically shows VEL (the current speed). Hold SET down for a second to change the display over to ODO (total kilometres). Hold SET down again for 1 second, in order to change over to DST (trip distance). When you press SET briely again, you return once more to VEL (the current speed).
9.2 Range The distance you can travel using the power assist with the battery ully charged depends on several factors: • • • Selected assist level If you want to cover a large distance with power assist, select the smaller gears, i.e. the ones that are easier to pedal. Also select a low assist level (Economic). How you ride If you are riding in gears that are harder to pedal and select a high assist level, the motor will produce plenty of power to help you along.
10 Troubleshooting 10.1 Code indication on the display If a code appears on your display, irst switch the Groove 2.0 system of at the battery. Wait for a moment, then switch it back on. If the error is still there, take the following table as a guide. The error code is displayed until the error is corrected. CODE CAUSE ERROR RECTIFICATION PO You are in a part of the menu that is only relevant to the bike manufacturer. Hold the 06 The low-voltage protection has triggered. Recharge the battery.
11 Removing and itting the ront wheel Fitting: Removal: 2. Fit the ront wheel. Chapter 18.2.1 "Original User Manual | General" (CD). 1. Pull apart the upper and lower halves of the electrical connector that is located at the rear of the fork. 1. Slide the cable ties with the cable on to the fork leg. 2. Slide the cable tie downwards rom the fork, or cut it. 3. Plug the two halves of the connector together. Take notice of the arrows on the connectors – they must be facing one another! 3.
We hope you thoroughly enjoy using your new Pedelec with Groove 2.0 drive. Reproduction, in whole or in part, is not permitted without the consent of Derby Cycle Werke GmbH / Raleigh Univega GmbH. Subject to misprints, errors and technical modiications.
