User manual

1
VGA can be used in cases where cable length is required to be longer than HDMI allows.
2
Use either the HDMI1 or HDMI2 input.
3
When using the DepthQ
®
Modulator, ensure you are projecting on a polarization-preserving screen (aka a “silver” screen).
4
To use DLP Link
TM
select "DLP-Link" 3D mode in the HDs3D2 Menu section instead of "DepthQ®". DLP-Link
TM
glasses do not use an IR emitter or the 3-pin mini-DIN connector.
5
The NVIDIA Quadro won't actually make a sync signal until there is actual 3D content being displayed.
LIMITED WARRANTY
Subject to the Limitaons, Exclusions and Disclaimers hereof, Lightspeed Design, Inc ("Lightspeed") warrants that the Projector,
Lamps and Accessories (hereinaer collecvely or individually referred to as "Product" as appropriate) will conform to Lightspeed’s
specificaons and be free from defects in material or workmanship for the respecve Limited Warranty period provided below. If
the Product, while subject to this Limited Warranty, is defecve in material
or workmanship during the warranty period, then
Lightspeed, at its opon, will REPAIR or REPLACE the Product. Lightspeed’s sole obligaon is to supply (or pay for) all labor necessary
to repair the Product found to be defecve within the Limited Warranty period and to repair or replace defecve parts with new parts
or, at the opon of Lightspeed, serviceable used parts that are equivalent or superior to new parts performance, but shall not exceed
the re
turn of the amount of the purchase price paid by the purchaser.
Limited Warranty Periods are as follows:
• Projector Product Limited Warranty Period (Excluding Lamps): Two (2) years from date of proof of purchase.
• The warranty period for LCD engines is either 1 year from the date of purchase of the projector or 2500 hours of projector
usage, whichever comes first.
• Lamp Product Limited Warranty Periods: Unless the maximu
m lamp hours noted in the Product specificaon (see
www.depthq.com/support) have been exceeded thereby voiding the Lamp Product Limited Warranty, the original installed
lamp shall have a six (6) month Limited Warranty period from date of Projector proof of purchase. All replacement Lamps will
have a six (6) month Limited Warranty from date of Lamp proof of purchase, and replacement lamps purchased at the me of
Projector Product purchase will
have a six (6) month Limited Warranty from date of first use, unless the maximum lamp hours
noted in the Product specificaon have been exceeded thereby voiding the Lamp Product Limited Warranty.
• Accessory Product Limited Warranty Period: Ninety (90) days from date of purchase.
WARRANTY LIMITATION AND EXCLUSION
THIS WARRANTY SETS FORTH LIGHTSPEED’S MAXIMUM LIABILITY FOR ITS PRODUCT. THIS WARRANTY EXTENDS ONLY TO PRODUCTS
PURCHASED F
ROM LIGHTSPEED OR A LIGHTSPEED AUTHORIZED RESELLER.
Lightspeed shall have no further obligaon under the foregoing Limited Warranty if the Product has been damaged due to abuse,
misuse, exposure to smoke, accident, service other than by Lightspeed or its authorized agents, or failure caused other than from
ordinary use or failure to properly use the Product in the applicaon for which said Product was intended. In addion, failure of the
end-user to follow main
tenance procedures as outlined in the Product's user guide will not be covered under this Warranty. Finally,
Lightspeed shall have no further obligaon if Lightspeed Product was subjected to operang condions outside of the range specified
in the user's guide or in this warranty. This warranty does not cover maintenance/repair/replacement of parts due to normal wear and tear.
Use of a lamp that is not a genuine InFocus lamp manufactured accordin
g to InFocus specificaons may void the warranty of the
Lightspeed Product in which the non genuine lamp was installed. In such a case, Lightspeed will not have any further obligaon
for the Lightspeed Product. Remanufactured Products and Soware Products are exempt from the foregoing Limited Warranty.
Please refer to the appropriate Remanufactured Product Limited Warranty or Soware Product Limited Warranty for applicable
Warranty informaon.
DISCLAIMER OF UNSTAT
ED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR
PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND THE
FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED B
Y LIGHTSPEED.
SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY
NOT APPLY TO YOU.
LIMITED WARRANTY PERIOD
The Limited Warranty periods hereof commence on the date of proof of purchase by the end-user customer. SOME JURISDICTIONS
MAY GRANT YOU CONSUMER RIGHTS WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE DURATIONS PROVIDED
HEREIN, AND LIGHTSPEED WILL HONOR ALL SUCH CONSUMER RIGHTS U
PON PROOF OF PURCHASE IN THAT JURISDICTION. To Obtain
Warranty Service: During the Limited Warranty period, to exercise this Limited Warranty, the purchaser must first contact 1) Lightspeed
(Mailing address: Lightspeed Design, Inc., 1611 116 ave NE, Suite 112, Bellevue, WA 98004-3048 USA; or via the web at
th
www.depthq.com/support), 2) a service facility authorized by Lightspeed or 3) the place of original purchase. For Warranty service,
the purchaser will pay to return or deliver the defecve Product and will pay all f
reight, duty, taxes, VAT, fees, incidental clearance and
customs charges to ship the unit to a Lightspeed Service Center or to a service facility authorized by Lightspeed. When returning
Product to Lightspeed, a Return Material Authorizaon Number (RMA #) is required and must be clearly displayed on the outside of
the shipping carton or a similar package affording an equal degree of protecon. Lightspeed or the service facility authorized by
Lightspeed will return the repaired/
replaced Product freight prepaid to the purchaser.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT LIGHTSPEED’S LIABILITY SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE
PRICE PAID BY PURCHASER. Where applicable naonal or state law prohibits the exclusion or limitaon of liability, Lightspeed excludes
or limits its liability to the maximum extent permied by naonal law. Limitaon on Bringing Acon - No acon, regardless of form,
ar
ising out of the agreement to purchase the Product may be brought by purchaser more than one year aer the cause of acon has
accrued. Governing Law - Any acon, regardless of form, arising out of the agreement to purchase the Product is governed by the
laws of the state of Washington, USA. Mandatory Arbitraon - Any acon, regardless of form, arising out of the agreement to purchase
the Product is subject to mandatory arbitrao
n. THIS WARRANTY DOES NOT AFFECT YOUR LEGAL RIGHTS UNDER APPLICABLE
NATIONAL LAWS RELATING TO THE SALE OF CONSUMER PRODUCTS.
DECLARATION OF CONFORMITY
For Declaraon of Conformity informaon, see the cerficaon label on the product and the user documentaon available for download
at www.depthq.com/support
Adjust the zoom first, then focus the
center of the image.
Refer to the User Manual for more
detailed information regarding
Front/Rear projection, keystoning,
throw ratios, and much more.
Use the Image-Zoom Control (A) to
adjust the size of the projected
image.
Use the Image-Focus Control (B) to
sharpen the projected image.
Adjust Zoom and Focus
Identical to “PC GeForce or Quadro (3D Vision) + DepthQ
®
Modulator”, except
for Steps 3 & 4:
Steps 1-2: Refer to Steps 1-2 of “PC GeForce or Quadro (3D Vision) + DepthQ
®
Modulator”.
Step 3: Connect your Active Shutter Glasses system to the 3D Sync output 3-pin
mini-DIN on the back of the DepthQ
®
HDs3D2 Projector.
Step 4: Position your emitter per system instructions, connect power, activate
your 3D shutter glasses (if required) and don them.
Step 5: Run your 3D-enabled application.
5
Enjoy either ~120Hz or ~144Hz 3D.
PC GeForce or Quadro (3D Vision)
+ Generic Active or DLP Link
®4
3D Glasses
3D
Step 1: Connect the supplied DVI-to-HDMI cable between the Computer's NVIDIA
GeForce or Quadro card and the back of the DepthQ
®
HDs3D2 Projector.
2
Step 2: In the NVIDIA Control Panel, under Stereoscopic 3D, select Set up
stereoscopic 3D, check Enable stereoscopic 3D then click the Apply button.
Then set Stereoscopic 3D display type to 3D TV Play and click the Apply button.
Step 3: Connect your DepthQ
®
Polarization Modulator Control Unit to the 3D Sync
output 3-pin mini-DIN on the back of the DepthQ
®
HDs3D2 Projector.
Step 4: Position the DepthQ
®
Modulator in front of the lens, tilt it towards the
center of your silver screen
3
, connect power, and don your Passive 3D glasses.
Step 5: Run your 3D-enabled application.
5
The DepthQ
®
Polarization Modulator
Control Unit will report either ~120Hz or ~144Hz depending on your resolution.
PC GeForce or Quadro (3D Vision) + DepthQ
®
Modulator
1280x720 60P or 1920x1080 24P
3D
Step-by-Step Set-Up Guide, cont’d
c
Step 1: Plug in the NVIDIA 3D Vision emitter to an open USB port on your
computer.
Step 2: Connect the supplied DVI-to-HDMI cable between the Computer's NVIDIA
Quadro card and the back of the DepthQ
®
HDs3D2 Projector.
2
Step 3: Set the Windows Desktop resolution under "PC" to 1280x720 (or
1280x800) and 120Hz refresh rate.
Step 4: In the NVIDIA Control Panel, under Manage 3D Settings, set Stereo -
Enable to On, and set Stereo - Display Mode to Generic Active Stereo (with
NVIDIA 3D Vision).
Step 5: Position your emitter per system instructions, connect power, activate
your 3D shutter glasses (if required) and don them.
Step 6: Run your 3D-enabled application.
5
The DepthQ
®
Polarization Modulator
Control Unit will report ~120Hz. Enjoy single-flashed 120Hz 3D.
PC Quadro (3D Vision) + NVIDIA 3D Glasses
1280x720 & 1280x800 120Hz
3D
Identical to “PC Quadro 10 80P + DepthQ
®
Modulator”, except for Steps 4 & 6:
Steps 1-3: Refer to Steps 1-3 of “PC Quadro 1080P + DepthQ
®
Modulator”.
Step 4: Connect your Active Shutter Glass system to the 3D Sync output 3-pin
mini-DIN on the back of the DepthQ
®
HDs3D2 Projector.
Step 5: Refer to Step 5 of “PC Quadro 1080P + DepthQ
®
Modulator”.
Step 6: Position your emitter per system instructions, connect power, activate
your 3D shutter glasses (if required) and don them.
Step 7-8: Refer to Steps 7-8 of “PC Quadro 1080P + DepthQ
®
Modulator”.
PC Quadro 1080P + Generic Active or DLP Link
®4
3D
Identical to “PC Quadro 720P + DepthQ
®
Modulator”, except for Steps 4 & 5:
Steps 1-3: Refer to Steps 1-3 of “PC Quadro 720P + DepthQ
®
Modulator”.
Step 4: Connect your Active Shutter Glass system to the 3D Sync output 3-pin
mini-DIN on the back of the Computer's NVIDIA Quadro card.
Step 5: Position your emitter per system instructions, connect power, activate
your 3D shutter glasses (if required) and don them.
Step 6: Run your 3D-enabled application.
5
Enjoy single-flashed 120Hz 3D.
PC Quadro 720P + Generic Active or DLP Link
®4
3D
Step 6: Position the DepthQ
®
Modulator in front of the lens, tilt it towards the
center of your silver screen
3
, connect power, and don your Passive 3D glasses.
Step 7: Run your 3D-enabled application.
5
The DepthQ
®
Polarization Modulator
Control Unit will report ~120Hz. Enjoy double-flashed 120Hz 3D.
Step 8: The L>R R>L Eye-Coding will be selected randomly upon projector sync.
You may have to use your 3D app to change the stereo polarity (swap eyes) to
correct for pseudo-stereo. Exiting the app or otherwise causing the projector to
re-sync will again choose a random eye-coding. This is normal.
(Cont’d)
Step-by-Step Set-Up Guide, cont’d
b
Step 1: Connect the supplied DVI-to-HDMI cable between the Computer's NVIDIA
Quadro card and the back of the DepthQ
®
HDs3D2 Projector.
2
Step 2: Set the Windows Desktop resolution under "PC" to 1920x1080 and 60Hz
refresh rate.
Step 3: In the NVIDIA Control Panel, under Manage 3D Settings, set Stereo -
Enable to On, and set Stereo - Display Mode to Generic Active Stereo.
Step 4: Connect your DepthQ
®
Polarization Modulator Control Unit to the 3D Sync
output on the back of the DepthQ
®
HDs3D2 Projector.
Step 5: Turn on 3D in the DepthQ
®
HDs3D2 Projector: Using the DepthQ
®
HDs3D2 remote, press Menu; then use the left or right arrows to highlight
Settings 1 and press “Enter” , then arrow down to Advanced 1 and press ;
then arrow up to highlite 3D Setting and ; then arrow up to select 3D and ;
finally arrow right to select DepthQ® and . Let the menu time out and it will
disappear.
(Continue to Steps 6-8 on next page)
PC Quadro 1080P + DepthQ
®
Modulator3D
Step 1: Connect the supplied DVI-to-HDMI cable between the Computer's NVIDIA
Quadro card and the back of the DepthQ
®
HDs3D2 Projector.
2
Step 2: Set the Windows Desktop resolution under "PC" to 1280x720 (or
1280x800) and 120Hz refresh rate.
Step 3: In the NVIDIA Control Panel, under Manage 3D Settings, set Stereo -
Enable to On, and set Stereo - Display Mode to On-board mini-DIN Connector.
Step 4: Connect your DepthQ
®
Polarization Modulator Control Unit to the 3D Sync
output 3-pin mini-DIN on the back of the Computer's NVIDIA Quadro card.
Step 5: Position the DepthQ
®
Modulator in front of the lens, tilt it towards the
center of your silver screen
3
, connect power, and don your Passive 3D glasses.
Step 6: Run your 3D-enabled application.
5
The DepthQ
®
Polarization Modulator
Control Unit will report ~120Hz. Enjoy single-flashed 120Hz 3D.
PC Quadro 720P + DepthQ
®
Modulator3D
Sat/Cable + Generic Active or DLP Link
®4
3D Glasses
Step 1: Connect the HDMI cable between the Sat/Cable Box and the back of the
DepthQ
®
HDs3D2 Projector.
2
Step 2: Play some 3D content to determine whether it is in a Side-by-Side or
Top/Bottom format.
Step 3: Turn on 3D in the DepthQ
®
HDs3D2 Projector: Using the DepthQ
®
HDs3D2 remote, press Menu; then use the left or right arrows to highlight
Settings 1 and press “Enter” , then arrow down to Advanced 1 and press ;
then arrow up to highlite 3D Setting and ; then arrow up to select 3D Format
and ; finally arrow up or down to select either Top/Bottom or Side by Side and
. Let the menu time out and it will disappear.
Step 4: Connect your Active Shutter Glasses system to the 3D Sync output 3-pin
mini-DIN on the back of the DepthQ
®
HDs3D2 Projector.
Step 3: Position your emitter per system instructions, connect power, activate
your 3D shutter glasses (if required) and don them.
Step 4: Play your 3D content. Enjoy double-flashed 120Hz Stereo 3D.
3D
Step-by-Step Set-Up Guide, cont’d
a