32”LED TV Model NO.
Contents Contents Safety Information 1-3 Product Introduction 4 Connections 5 Remote Control 6-7 AUTO INSTALLATION 8-9 Basic Operation 10 OSD Menu 1. Picture menu 2. Sound menu 3. Channel menu 4. Feature menu 5.
Safty Information Safety Information 1
Safety Information Safety Information IMPORTANT SAFETY INFORMATION (Continued) This unit has been produced according to all current safety regulations. The following safety tips should safeguard users against careless use and the dangers connected with such use. Although this appliance has been carefully manufactured and rigorously checked prior leaving the factory, as with all electrical appliances it is possible for problems to develop.
Safety Information Safety Information IMPORTANT SAFETY INFORMATION (continued) Liquids spilt into the unit can cause serious damage. Switch the set OFF and disconnect the mains power supply, then consult a qualified service person before attempting to use the unit again. Do NOT remove the safety covers. There are no useable or serviceable parts inside. You may invalidate the warranty. Qualified personnel must only service this apperatus. Do NOT tap or shake the screen, you may damage the internal circuits.
Product Introduction Product Introduction Front View LED indicator Remote Control window(keep clear) INPUT MENU CH- CH+ VOL- VOL+ POWER The functions of the TV buttons are described below. INPUT: Press to select the source. MENU: Press to display the OSD menu, Press again to exit the menu. CH+/CH-: Press to scan through channels. They are also can be used to move down/up in the OSD menu screen. VOL+/VOL-: Press to adjust the volume.
Connections VGA Common Interface MINI YPbPr MINI AV DVB-S2 USB Connections Headphone HDMI1 HDMI2 HDMI3 SCART COAX RF PC - IN AC POWER IN AC POWER IN: Connect to power. Headphone: Connect it to your headphone or other audio equipment. HDMI1/2/3: Connect it to the HDMI of DVD or other equipment. SCART: Connect them to the SCART video output terminal of DVD. Coax: Digital output to AV receiver. RF: Connect antenna or cable 75 Ohm coaxial to receive TV signal.
Remote Control Remote Control The remote control is using Infra-Red(IR). Point it towards the front of the TV. The remote control may not work correctly if it is operated out of range or out of angle. POWER PICTURE MUTE SOUND ASPECT SLEEP EPG FAV SUBTITLE CH.LIST TV/RADIO INPUT POWER(red button): Turn the TV on/standby. MUTE: Press to mute the sound, press again or press VOL+ to unmute. PICTURE: Select the picture mode. SOUND: Select the sound mode.
Remote Control Remote Control POWER PICTURE MUTE SOUND ASPECT SLEEP EPG FAV SUBTITLE CH.LIST TV/RADIO INPUT OK MENU EXIT 1 2 3 4 5 6 7 8 DISPLAY 9 0 VOL TV/TXT INDEX CH CANCEL REVEAL HOLD SIZE NICAM/A2 SUBPAGE VOL +/- : Volume +/-. CH / : Channel/Program +/-. : Play/pause program. : Stop program. : Fast reverse. : Fast forward. : Previous chapter. : Next chapter. Colour buttons : Short cuts-follow the coloured links in the text.
AUTO INSTALLATION AUTO INSTALLATION Setup 1:Set up the Home Mode Setup 2:Set up the Country Setup 3:Set up the Language 8
AUTO INSTALLATION AUTO INSTALLATION Setup 4:Set up the Auto Power Off Setup 5:Set up the TV Connection If select “Air” or “Cable”, it will show “Auto Search” in Setup 6 If select “Satellite”, it will show “Satellite setup” in Setup 6 Setup 6: Set up the Auto Search Setup 6: Set up the Satellite setup 6 6 9
Basic Operation Basic Operation Power on/off 1. Connect to the power supply. 2. -To turn on the TV Press POWER button on the TV or remote control. -To turn off the TV Press POWER button on the TV or remote control. Input Source select Press INPUT button on the TV set or remote control to display the input source menu, and use CH+/- button on the TV set or Ĥ0ĥ!button on remote control to select the input source, press OK button on the remote control to enter.
OSD Menu OSD Menu 1. Picture menu Description Picture Mode: Select your desired picture mode from Dynamic, Standard, Mild and User. Brightness: Adjust image black level. Contrast: Adjust image contrast. Sharpness: Adjust the sharpness(Gray and invalid in VGA/PC mode). Colour: Adjust image colour from black and white. Tint: Control the tint ( NTSC mode only). Colour Temp.: Select an optimum color temperature mode to suit your eyes for viewing from Warm, Cool, Standard.
OSD Menu OSD Menu 2. Sound menu Description Sound Mode: Select your desired sound mode from Standard, Movie, Music, Speech and User. Bass: Adjust the level of the lower-pitched sounds. Treble: Adjust the level of the higherpitched sounds. Balance: Adjust the audio output between left and right speakers. Surround: Turn on/off the surround sound function. Auto Volume Level (AVL): The volumes of all sources will be maintained when the function’s on.
OSD Menu OSD Menu 3. Channel menu(In ATV/DTV mode) OK Channel Management: Enter the Channel management menu to edit the channels. Move Delete: Press RED button to sign the channels you want to delete, it will hint you when you exit. Lock: User must set the “Lock enable”(Feature-Lock- Lock enable) at ON to active this function. Press GREEN button to sign(lock) or cancel(unlock) the channel. And you have to enter the password to view the program.
OSD Menu OSD Menu Country: Select the country. TV Connection: Select DTV type, you can choose Air(DVB-T), Cable(DVB-C), Satellite(DVB-S2), as you like. Auto Search: Press OK button to enter the Auto Search menu, select search mode, and press OK button to start auto search. Note: 1. ALL: Auto search channels for DTV, ATV and Radio. DTV: Auto search channels for DTV and radio. ATV: Auto search channels for ATV. 2.
OSD Menu OSD Menu Satellite System Press button to select the “TV Conection” , and set it on “Satellite”.
OSD Menu OSD Menu Satellite System Press button to select the “TV Conection” , and set it on “Satellite”. OK Press button to select the “Satellite System” , show as follow: Operations in Satellite List Menu are shown in the following table: Key Stroke KEY_UP KEY_DOWN KEY_LEFT Action use cursor to up use cursor to down KEY_RIGHT switch operation to satellite system parameters setting list switch operation to Transponder list KEY_MENU KEY_EXIT Exit Main Menu.
OSD Menu OSD Menu 4. Feature menu Lock: This menu allows you to lock certain features of the television so that they can not be used or viewed. For example if you don’t want certain channels viewed by children or if the television is to be used in a hotel and you want certain channels be locked. When you enter the system lock menu you will be asked for a password. As default it is 0000. Lock Enable - Turn on/off the Lock functions.
OSD Menu OSD Menu Hotel Mode - Enter the Hotel Setting menu. Hotel Lock: Turn on/off the Hotel Lock function. Channel Lock: Disable the Channel menu in OSD. Picture Lock: Disable the Picture menu in OSD. Sound Lock: Disable the Sound menu in OSD. Feature Lock: Disable the Feature menu in OSD. Setup Lock: Disable the Setup menu in OSD. Key Lock: Disable the buttons on the TV set. Source Lock: Disable the input source you desired. Set Source: Select the default source when you turn on the TV.
OSD Menu OSD Menu 5. SETUP menu OK OSD Timer: Lets you adjust the amount of time the On Screen Menu stays on the screen before disappearing. Auto SCART: The TV will be changed to SCART source automatically when you connect the TV to the SCART device. PC Setup: Change the PC Settings in PC mode. Auto Adjust: Setup the parameter of the screen automatically. H/V-Position: Adjust the transverse/vertical position of the screen.
Multimedia Operation Multimedia Operation Basic Operation 1). Press the INPUT button on the remote control to display the input source menu, select Media source by the / buttons, and press OK button to enter the Multimedia menu as shown below. 2). Insert USB device, and select the Media mode form Photo, Music, Movie and eBook, then you will find the name of the device display on the screen as shown below. 3).
Multimedia Operation Multimedia Operation 1. Photo Play the photo Press / button to select the option on the table, and press OK button to change. Note: You could press OK button to display the option table when it disappears. Play/Pause the photo playing. Stop and exit the full screen program. Play the previous or next file directly. Ratate the picture(0, 90, 180, 270). Zoom in/out the picture, you could move the picture by Cursor left/right/up/down button in Zoom mode.
Multimedia Operation Multimedia Operation 3. Movie Play the movie Press / button to select the option on the table, and press OK button to change. Note: You could press OK button to display the option table when it disappears. AB Play/Pause the movie playing. Stop and exit the full screen program. Play fast backword or forword. Play the movie in slow mode. Play the movie in step mode. Set the A-B repeat playing mode. Play the previous or next file directly. Display the playing list.
EPG menu EPG menu Press EPG button on the remote control to display the EPG menu. EPG mode: Press RED button to change the EPG display mode. Daily mode: shows the information of the programs to be broadcasted in daily mode. Weekly mode: shows the information of the programs to be broadcasted in weekly mode. Reminder: Press GREEN button once to remind the program for watching, and press GREEN button again to cancel. For detail reminder settings, please take following for reference.
Technical Specifications Display technology Screen size, visible Screen format Resolution Minimum contrast ratio Minimum brightness Display colors Minimum viewing angle Maximum response time Picture repetition rate Video color systems TV Standard CATV (optional) Chanels (ATV / DVB-T / -C / -S2) Videotext (ATV / DTV) AC 100-240 Volt INPUT USB HDMI SCART PC AUDIO IN VGA AV (viar adapter cable) YPBPR (via adapter cable) COAXIAL OUTPUT DVB-T/-C / TVRF ANT.
Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment and batteries) is not handled correctly. Electric and electronic equipment and batteries is marked with the crossed out trash can symbol, seen below.
